Massive MIMO transmission techniques

Next generation of mobile communication systems must support astounding data traffic increases, higher data rates and lower latency, among other requirements. These requirements should be met while assuring energy efficiency for mobile devices and base stations. Several technologies are being proposed for 5G, but a consensus begins to emerge. Most likely, the future core 5G technologies will include massive MIMO (Multiple Input Multiple Output) and beamforming schemes operating in the millimeter wave spectrum. As soon as the millimeter wave propagation difficulties are overcome, the full potential of massive MIMO structures can be tapped. The present work proposes a new transmission system with bi-dimensional antenna arrays working at millimeter wave frequencies, where the multiple antenna configurations can be used to obtain very high gain and directive transmission in point to point communications. A combination of beamforming with a constellation shaping scheme is proposed, that enables good user isolation and protection against eavesdropping, while simultaneously assuring power efficient amplification of multi-level constellations

Towards low-cost gigabit wireless systems at 60 GHz

The world-wide availability of the huge amount of license-free spectral space in the 60 GHz band provides wide room for gigabit-per-second (Gb/s) wireless applications. A commercial (read: low-cost) 60-GHz transceiver will, however, provide limited system performance due to the stringent link budget and the substantial RF imperfections. The work presented in this thesis is intended to support the design of low-cost 60-GHz transceivers for Gb/s transmission over short distances (a few meters). Typical applications are the transfer of high-definition streaming video and high-speed download. The presented work comprises research into the characteristics of typical 60-GHz channels, the evaluation of the transmission quality as well as the development of suitable baseband algorithms. This can be summarized as follows. In the first part, the characteristics of the wave propagation at 60 GHz are charted out by means of channel measurements and ray-tracing simulations for both narrow-beam and omni-directional configurations. Both line-of-sight (LOS) and non-line-of-sight (NLOS) are considered. This study reveals that antennas that produce a narrow beam can be used to boost the received power by tens of dBs when compared with omnidirectional configurations. Meanwhile, the time-domain dispersion of the channel is reduced to the order of nanoseconds, which facilitates Gb/s data transmission over 60-GHz channels considerably. Besides the execution of measurements and simulations, the influence of antenna radiation patterns is analyzed theoretically. It is indicated to what extent the signal-to-noise ratio, Rician-K factor and channel dispersion are improved by application of narrow-beam antennas and to what extent these parameters will be influenced by beam pointing errors. From both experimental and analytical work it can be concluded that the problem of the stringent link-budget can be solved effectively by application of beam-steering techniques. The second part treats wideband transmission methods and relevant baseband algorithms. The considered schemes include orthogonal frequency division multiplexing (OFDM), multi-carrier code division multiple access (MC-CDMA) and single carrier with frequency-domain equalization (SC-FDE), which are promising candidates for Gb/s wireless transmission. In particular, the optimal linear equalization in the frei quency domain and associated implementation issues such as synchronization and channel estimation are examined. Bit error rate (BER) expressions are derived to evaluate the transmission performance. Besides the linear equalization techniques, a low-complexity inter-symbol interference cancellation technique is proposed to achieve much better performance of code-spreading systems such as MC-CDMA and SC-FDE. Both theoretical analysis and simulations demonstrate that the proposed scheme offers great advantages as regards both complexity and performance. This makes it particularly suitable for 60-GHz applications in multipath environments. The third part treats the influence of quantization and RF imperfections on the considered transmission methods in the context of 60-GHz radios. First, expressions for the BER are derived and the influence of nonlinear distortions caused by the digital-to-analog converters, analog-to-digital converters and power amplifiers on the BER performance is examined. Next, the BER performance under the influence of phase noise and IQ imbalance is evaluated for the case that digital compensation techniques are applied in the receiver as well as for the case that such techniques are not applied. Finally, a baseline design of a low-cost Gb/s 60-GHz transceiver is presented. It is shown that, by application of beam-steering in combination with SC-FDE without advanced channel coding, a data rate in the order of 2 Gb/s can be achieved over a distance of 10 meters in a typical NLOS indoor scenario

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

Beam scanning by liquid-crystal biasing in a modified SIW structure

A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium

Array communications in wireless sensor networks

Imperial Users onl

Beam Tracking Strategies for 5G New Radio Networks Operating in the Millimetre Wave Bands

[ES] La llegada de la próxima generación del estándar de comunicaciones móviles, la llamada quinta generación (5G), es prácticamente una realidad. Las primeras redes comerciales han comenzado a ser desplegadas, centrándose en ofrecer altas velocidades de transferencia de datos. Sin embargo, el estándar 5G va mucho más allá y prevé dar soporte a nuevos servicios que pretenden revolucionar la sociedad. Estos nuevos servicios imponen un nivel alto de requisitos en no solo en cuanto a velocidad del tráfico de datos, sino en cuanto a latencia o número de dispositivos conectados simultáneamente. La amplia variedad de requisitos no puede ser soportada por las redes de cuarta generación (4G), por lo que se hizo necesario plantear un nuevo paradigma para las redes inalámbricas. Con la promesa de grandes cantidades de ancho de banda sin utilizar, el estándar 5G contempla utilizar frecuencias en la comúnmente conocida como banda de milimétricas (mmWave). Esta banda presenta grandes pérdidas de propagación, que se acentúan si existen bloqueos de señal. Actividades regulatorias del uso de las bandas de milimétricas atrajo el interés tanto de la industria como de la academia en plantear soluciones para dar servicio en estas bandas. En los últimos años se han presentado infinidad de trabajos basados en sistemas con múltiples antenas o MIMO, para conformar las señales transmitidas o recibidas en haces apuntando en determinadas direcciones. La ganancia que aportan los sistemas MIMO pueden compensar las altas pérdidas de propagación, asegurando la viabilidad de las comunicaciones mmWave. Se ha detectado una evidente falta de estudios sobre la viabilidad de sistemas MIMO en entornos móviles y dinámicos con bloqueos que hagan necesario que el sistema se reconfigure. Esta Tesis pretende cubrir este espacio desde un enfoque práctico y propone mecanismos de gestión de los haces para hacerles un seguimiento utilizando los recursos y mecanismos del nuevo estándar 5G. Las soluciones aportadas se basan en el uso eficiente de los reportes de medidas de las señales de referencia estandarizadas en enlace descendente. En primer lugar, esta Tesis recoge un análisis minucioso del estado del arte, donde se corrobora la necesidad de aportar soluciones de seguimiento de haces en sistemas de comunicaciones en la banda de milimétricas. Además, se estudian los diferentes mecanismos definidos en el estándar 5G y que posibilitan el seguimiento. Cabe destacar que el estándar no define un mecanismo único a seguir, permitiendo presentar propuestas. Una vez conocidas las tecnologías, se centra el estudio en el impacto del seguimiento sobre las prestaciones a nivel de red y de enlace. Dicho estudio se realiza sobre un sistema punto a punto, donde el terminal móvil se desplaza por un entorno urbano. En base a simulaciones de red, se cuantifica el índice de seguimiento de haz y de cómo dicho seguimiento afecta a la relación señal a ruido más interferencia (SINR) y la tasa de transmisión del usuario. Las soluciones de seguimiento propuestas en esta Tesis se pueden clasificar en dos categorías. En una primera categoría, se realiza el seguimiento en base a reportes de medidas de las señales de referencia. Independientemente de la velocidad, se alcanza un seguimiento del 91% con poca penalización en la tasa de transmisión si se monitorizan los haces de interés con una periodicidad menor de 20 ms. En la segunda categoría caben mecanismos de seguimiento que hacen uso de fuentes externas de información. Dentro de esta categoría, se propone un fingerprinting que relacione haces con la localización reportada y un modelo de machine learning (ML) que prediga los haces a utilizar. El fingerprinting proporciona los mismos niveles de rendimiento. Sin embargo, esta solución es muy sensible a errores y requiere considerar todos los casos posibles, lo que la hace tecnológicamente inviable. En cambio, el modelo de ML, que hace p[CA] L'arribada de la següent generació de l'estàndard de comunicacions mòbils, l'anomenada cinquena generació (5G), es pràcticament una realitat. Les primeres xarxes comercials han començat a desplegar-se i s'han centrat en oferir altes velocitats de transferència de dades. No obstant, l'estàndard 5G va molt mes allà y preveu donar suport a nous serveis que pretenen revolucionar la societat. Estos nous serveis imposen un alt nivell de requisits no sols en quant a velocitat de tràfic de dades, si no també en quant a latència o número de connexions simultànies. L'ampla varietat de requisits no es suportada per les xarxes de quarta generació (4G) actuals, per el qual es va fer necessari un nou paradigma de xarxes sense fil. Amb la promesa de amplies quantitats d'ample de banda, l'estàndard 5G contempla utilitzar freqüències a la banda de mil·limètriques. Esta banda presenta l'inconvenient d'experimentar grans pèrdues de propagació, que s'accentuen en cas de bloqueigs. L'apertura de les bandes de mil·limètriques va atraure l'interès tant de l'industria com de l'acadèmia en plantejar solucions per a donar servei en estes bandes. En els últims anys s'han presentat infinitat de treballs basats en sistemes amb múltiples antenes o MIMO, per a conformar els senyals transmesos o rebuts en feixos apuntant en determinades direccions d'interès. El guany de feix es pot utilitzar per a compensar les pèrdues de propagació, assegurant la viabilitat de les comunicacions en la banda de mil·limètriques. No obstant això, s'ha detectat una preocupant manca d'estudis sobre la viabilitat d'estos sistemes en entorns mòbils i dinàmics, amb obstacles que bloquejen els feixos i facen necessari que el sistema es reconfigure. El present treball de Tesi pretén cobrir este espai buit i des d'un punt de vista pràctic, es proposen mecanismes de gestió dels feixos per a ser el seguiment utilitzant els recursos i mecanismes dels que disposa l'estàndard 5G. D'esta manera, les solucions aportades es basen en la utilització eficient dels reports de mesures dels senyals de referència del enllaç descendent. En primer lloc, esta Tesi recull una anàlisi minuciosa de l'estat de l'art on es corrobora la necessitat de aportar solucions de seguiment de feixos per a comunicacions en la banda de freqüències mil·limètriques. A més a més, s'estudien els diferents mecanismes definits a l'estàndard 5G i que possibiliten el seguiment. Cap destacar que l'estàndard no defineix un mecanisme únic, si no que deixa la porta oberta a presentar propostes. Una vegada conegudes les tecnologies, l'estudi es centra en l'impacte del seguiment sobre les prestacions a nivell de xarxa i d'enllaç. Este estudi es realitza sobre un sistema MIMO punt a punt, en una única estació base i un terminal mòbil desplaçant-se en un entorn urbà. En base a simulacions d'extrem a extrem, es quantifica l'índex de seguiment de feix i com l'anomenat seguiment afecta a la relació senyal a soroll més interferència (SINR) i a la taxa instantània de transmissió de l'usuari. Les solucions de seguiment de feixos propostes a la Tesi es poden classificar en dos categories. A la primera categoria, el seguiment de feixos es realitza en base als reports de mesures dels senyals de referència. Independentment de la velocitat, s'arriba a una taxa de seguiment del 91% amb poca penalització de taxa de transmissió si els feixos d'interès es mesuren amb una periodicitat menor a 20 ms. A la segona categoria pertanyen els algoritmes que utilitzen fonts d'informació externes. Dins d'aquesta categoria es proposa un fingerprinting que relaciona un parell de feixos amb la ubicació de l'usuari, i a banda un model d'intel·ligència artificial (IA) que preveu el feix a utilitzar. El fingerprinting ofereix el mateix rendiment. Però, esta solució es molt sensible a errors i requereix considerar tots els casos possibles, fent-la tecnològicament inviable. En canvi, el[EN] The arrival of the next generation of mobile communication standards, the so-called Fifth Generation (5G), is already a reality. The first commercial networks have begun to be deployed, and they focus on providing higher data rates. However, the 5G standard goes much further from that and aims at providing support to new services which will revolutionise the society. These new services impose a high level of requirements not only in terms of the data traffic speed, but also in terms of very low latency or incredibly large number of simultaneous connections. This wide variety of requirements cannot be technologically supported by the current Fourth Generation (4G) networks, so it became necessary to move forward with a new paradigm for wireless networks. With the promise of large amounts of bandwidth, in the order of GHz, the 5G standard contemplates the use of frequencies in the commonly known Millimetre Wave (mmWave) band. The mmWave band experiences large propagation losses, which are accentuated in blockage events. Regulatory activities worldwide in the mmWave bands attracted the interest of both the industry and the academia. In the last few years, a tremendous number of contributions on mmWave propagation studies and networks have appeared, most of them based on Multiple-Input Multiple-Output (MIMO) solutions. MIMO architectures allow to beamform, which focuses the radiated energy on certain directions of interest called beams. The additional beam gain compensates the high propagation losses, ensuring the viability of the communications in the mmWave band. There is an evident lack of viability studies of mmWave MIMO systems in mobile and highly-dynamic environments, where obstacles may block beams and forcing frequent re-configurations. This Thesis work aims to fill this gap from a practical approach. This Thesis proposes beam management mechanisms utilising the mechanisms and resources offered by the Third Generation Partnership Project (3GPP) 5G radio access standard: 5G New Radio (NR). The practical solutions are based on the efficient use of measurement reports of standardised downlink Reference Signals (RS). In first place, this Thesis provides a thorough state-of-the-art analysis and corroborates the need of adopting beam tracking solutions for mmWave networks. Then, a complete overview of the 5G standard mechanisms that enable beam tracking is given. The NR standard does not define a standardised mechanism for beam tracking, leaving the door open to proposals to carry out such monitoring. Once the technologies have been identified, the Thesis continues with assessing the impact of the beam tracking strategies on the network and link-level performance. The study is focused on individual point-to-point mmWave links in a realistic urban environment. Based on end-to-end network simulations, the Thesis is interested in assessing the beam tracking success ratio and how beam misalignment affects the perceived Signal to Noise plus Interference Ratio (SINR) and user throughput at pedestrian and vehicular speeds. The beam tracking solutions proposed in this Thesis fall into two categories. The first category monitors beams based on measuring and reporting beamformed RS. Regardless of the speed, this beam tracking category provides up to 91 % tracking performance, with little throughput reduction if the beams of interest are measured with a periodicity below 20 ms. Beam tracking in the second category relies on external information sources. Within this category, this Thesis proposes a fingerprinting database relating beams to the user position and a machine learning (ML) model. Fingerprinting beam tracking is technologically viable and provides similar performance levels. However, this solution is very sensitive to errors and requires considering all possible situations. The ML beam tracking, which makes predictions with a 16 % of estimation error for the reference data set.I want to thank the Spanish Ministry of Education and Professional Formation for funding this Thesis work with an official pre-doctoral contract grant.Herranz Claveras, C. (2019). Beam Tracking Strategies for 5G New Radio Networks Operating in the Millimetre Wave Bands [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/130845TESI

Moniantennijärjestelmät autoympäristössä

MIMO systems have emerged in the last few years as a means to improve the quality of service and spectral efficiency of wireless communication systems. This thesis examines the use of multi-antenna systems on vehicles. The main objectives of this thesis are to develop a procedure for the design of multi-antenna systems, compare the benefits of different multi-antenna systems in automotive environment, study the suitability of the chosen electromagnetic simulation method to modelling and simulation of automotive antennas, and also to give ample references for the reader, in case a more in-depth understanding in the areas of multi-antenna techniques and automotive antennas is needed. The electromagnetic simulation of the antenna systems are based on the finite integration technique with commercial software, while link level performance simulation is performed on a MATLAB implementation of the SCME radio channel model. The finite integration technique is found to provide accurate radiation pattern results, and it can be recommended for the purpose of simulation of automotive antenna systems at the 700 MHz carrier frequency. On link level simulations the focus is on simulating 2×2 multiantenna systems. These simulations imply a noticeably improved BER when a BF MIMO system is employed, compared to the traditional MIMO system. The BF MIMO is a new concept that combines the best sides of beamforming and MIMO. This is the first study where the BF MIMO concept is applied to antennas in automotive environment. The results for the different antenna array configurations were indeterminate. In general, it can be said that the radio channel (or channel model) is one of the most significant factors in determining the performance of a multi-antenna systems, and it is highly unlikely that any single array configuration can provide optimal performance in every channel conditions. The first part of this thesis, Chapters 2 and 3, provides background of multi-antenna systems. Theoretical concepts of multi-antenna systems are introduced in Chapter 2 to enable the analysis of such systems. In the third chapter, a literature survey is presented as a summary of related studies on the areas of automotive antennas, multi-antenna systems, related information theory and electromagnetic simulation methods of antennas. In the latter part of this thesis, Chapter 4 describes the electromagnetic and link level simulation software packages and the simulation of the antennas. The results are presented in Chapter 5, and conclusions are drawn in Chapter 6. /Kir1

System capacity enhancement for 5G network and beyond

A thesis submitted to the University of Bedfordshire, in fulfilment of the requirements for the degree of Doctor of PhilosophyThe demand for wireless digital data is dramatically increasing year over year. Wireless communication systems like Laptops, Smart phones, Tablets, Smart watch, Virtual Reality devices and so on are becoming an important part of people’s daily life. The number of mobile devices is increasing at a very fast speed as well as the requirements for mobile devices such as super high-resolution image/video, fast download speed, very short latency and high reliability, which raise challenges to the existing wireless communication networks. Unlike the previous four generation communication networks, the fifth-generation (5G) wireless communication network includes many technologies such as millimetre-wave communication, massive multiple-input multiple-output (MIMO), visual light communication (VLC), heterogeneous network (HetNet) and so forth. Although 5G has not been standardised yet, these above technologies have been studied in both academia and industry and the goal of the research is to enhance and improve the system capacity for 5G networks and beyond by studying some key problems and providing some effective solutions existing in the above technologies from system implementation and hardware impairments’ perspective. The key problems studied in this thesis include interference cancellation in HetNet, impairments calibration for massive MIMO, channel state estimation for VLC, and low latency parallel Turbo decoding technique. Firstly, inter-cell interference in HetNet is studied and a cell specific reference signal (CRS) interference cancellation method is proposed to mitigate the performance degrade in enhanced inter-cell interference coordination (eICIC). This method takes carrier frequency offset (CFO) and timing offset (TO) of the user’s received signal into account. By reconstructing the interfering signal and cancelling it afterwards, the capacity of HetNet is enhanced. Secondly, for massive MIMO systems, the radio frequency (RF) impairments of the hardware will degrade the beamforming performance. When operated in time duplex division (TDD) mode, a massive MIMO system relies on the reciprocity of the channel which can be broken by the transmitter and receiver RF impairments. Impairments calibration has been studied and a closed-loop reciprocity calibration method is proposed in this thesis. A test device (TD) is introduced in this calibration method that can estimate the transmitters’ impairments over-the-air and feed the results back to the base station via the Internet. The uplink pilots sent by the TD can assist the BS receivers’ impairment estimation. With both the uplink and downlink impairments estimates, the reciprocity calibration coefficients can be obtained. By computer simulation and lab experiment, the performance of the proposed method is evaluated. Channel coding is an essential part of a wireless communication system which helps fight with noise and get correct information delivery. Turbo codes is one of the most reliable codes that has been used in many standards such as WiMAX and LTE. However, the decoding process of turbo codes is time-consuming and the decoding latency should be improved to meet the requirement of the future network. A reverse interleave address generator is proposed that can reduce the decoding time and a low latency parallel turbo decoder has been implemented on a FPGA platform. The simulation and experiment results prove the effectiveness of the address generator and show that there is a trade-off between latency and throughput with a limited hardware resource. Apart from the above contributions, this thesis also investigated multi-user precoding for MIMO VLC systems. As a green and secure technology, VLC is achieving more and more attention and could become a part of 5G network especially for indoor communication. For indoor scenario, the MIMO VLC channel could be easily ill-conditioned. Hence, it is important to study the impact of the channel state to the precoding performance. A channel state estimation method is proposed based on the signal to interference noise ratio (SINR) of the users’ received signal. Simulation results show that it can enhance the capacity of the indoor MIMO VLC system