Carbon Nanotubes

Since their discovery in 1991, carbon nanotubes have been considered as one of the most promising materials for a wide range of applications, in virtue of their outstanding properties. During the last two decades, both single-walled and multi-walled CNTs probably represented the hottest research topic concerning materials science, equally from a fundamental and from an applicative point of view. There is a prevailing opinion among the research community that CNTs are now ready for application in everyday world. This book provides an (obviously not exhaustive) overview on some of the amazing possible applications of CNT-based materials in the near future

A Vertical C60 Transistor with a Permeable Base Electrode

A high performance vertical organic transistor based on the organic semiconductor C60 is developed in this work. The sandwich geometry of this transistor, well known from organic light-emitting diodes or organic solar cells, allows for a short transfer length of charge carriers in vertical direction. In comparison to conventional organic field-effect transistors with lateral current flow, much smaller channel lengths are reached, even if low resolution and low-cost shadow masks are used. As a result, the transistor operates at low voltages (1 V), drives current densities in the range of 10 A/cm², and enables a switching speed in the MHz range. The operation mechanism is studied in detail. It is demonstrated that the transistor can be described by a nano-porous permeable base electrode insulated by a thin native aluminum oxide film on its surface. Thus, the transistor has to be understood as two metal-oxide-semiconductor diodes, sharing a common electrode, the base. Upon applying a bias to the base, charges accumulate in front of the oxide, similar to the channel formation in a field-effect transistor. Due to the increased conductivity in this region, charges are efficiently transported toward and through the pinholes of the base electrode, realizing a high charge carrier transmission. Thus, even a low concentration of openings in the base electrode is sufficient to ensure large transmission currents. The device concept turns out to be ideal for applications where high transconductance and high operation frequency are needed, e.g. in analog amplifier circuits. The full potential of the transistor is obtained if the active area is structured by an insulating layer in order to perfectly align the three electrodes. Besides that, molecular doping near the charge injecting contact is essential to minimize the contact resistance. Due to the high power density in the vertical C60 transistor, Joule self-heating occurs, which is discussed in this work in the context of organic semiconductors. The large activation energies of the electrical conductivity observed cause the presence of S-shaped current-voltage characteristics and result in thermal switching as well as negative differential resistances, as demonstrated for several two-terminal devices. A detailed understanding of these processes is important to determine restrictions and proceed with further optimizations.:CONTENTS Publications, patents and conference contributions 9 1 Introduction 13 2 Theory 19 2.1 From small molecules to conducting thin films . . . . . . . . . . . . . . . . . . . . 19 2.1.1 Aromatic hydrocarbons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.1.2 Solid state physics of molecular materials . . . . . . . . . . . . . . . . . . . 24 2.1.3 Energetic landscape of an organic semiconductor . . . . . . . . . . . . . . 26 2.1.4 Charge transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2.2 Semiconductor structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 2.2.1 Semiconductor statistics and transport . . . . . . . . . . . . . . . . . . . . 42 2.2.2 Charge injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 2.2.3 Limitations of the current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2.2.4 Metal-oxide-semiconductor structures . . . . . . . . . . . . . . . . . . . . . 57 2.3 Self-heating theory of thermistor device . . . . . . . . . . . . . . . . . . . . . . . . 61 3 Organic transistors 65 3.1 The organic field-effect transistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 3.1.1 Basic principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 3.1.2 Device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 3.1.3 Device geometries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 3.1.4 Device parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 3.1.5 Issues of OFETs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 3.1.6 Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 3.2 Overview over vertical organic transistors . . . . . . . . . . . . . . . . . . . . . . . 76 3.2.1 VOTs with an unstructured base electrode . . . . . . . . . . . . . . . . . . . 76 3.2.2 VOTs with structured base electrode . . . . . . . . . . . . . . . . . . . . . . 79 3.2.3 Charge injection modulating transistors . . . . . . . . . . . . . . . . . . . . 82 3.2.4 Vertical organic field-effect transistor . . . . . . . . . . . . . . . . . . . . . . 85 3.2.5 Development of the scientific output . . . . . . . . . . . . . . . . . . . . . . 87 3.2.6 Competing technologies and approaches . . . . . . . . . . . . . . . . . . . 88 3.3 Vertical Organic Triodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.3.1 Stucture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.3.2 Electronic configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.3.3 Energetic alignment of the diodes . . . . . . . . . . . . . . . . . . . . . . . 92 3.3.4 Current flow in the on and the off-state . . . . . . . . . . . . . . . . . . . . 94 3.3.5 Definition and extraction of parameters . . . . . . . . . . . . . . . . . . . . 95 4 Experimental 101 4.1 General processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 4.1.1 Thermal vapor deposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 4.1.2 Processing tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 4.1.3 Processing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2 Mask setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 4.3 Measurement setups and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 4.3.1 Current-voltage measurements . . . . . . . . . . . . . . . . . . . . . . . . . 108 4.3.2 Frequency-dependent measurements . . . . . . . . . . . . . . . . . . . . . 108 4.3.3 Impedance Spectroscopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3.4 Ultraviolet and X-ray Photoelectron Spectroscopy . . . . . . . . . . . . . . . 110 4.3.5 Thermal imaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 4.4 Materials used in C60 triodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 4.4.1 Buckminsterfullerene C60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 4.4.2 Tungsten paddlewheel W2(hpp)4 . . . . . . . . . . . . . . . . . . . . . . . . 116 4.4.3 Aluminum and its oxides . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 4.4.4 Spiro-TTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 4.5 Materials used in Organic Light-emitting Diodes . . . . . . . . . . . . . . . . . . . 121 5 Introduction of C60 VOTs 123 5.1 Sample preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 5.2 Diode characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 5.3 Base sweep measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 5.4 Determination of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 5.5 Common-base connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.6 Output characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 5.7 Frequency-dependent measurement . . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.8 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 6 Effect of annealing 141 6.1 Charge carrier transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 6.2 Sheet resistance and transmittance of the base electrode . . . . . . . . . . . . . . 142 6.3 Investigation of morphological changes . . . . . . . . . . . . . . . . . . . . . . . . 144 6.4 Photoelectron spectroscopy of the base electrode . . . . . . . . . . . . . . . . . . 153 6.5 Influence of air exposure and annealing onto the dopants . . . . . . . . . . . . . . 159 6.6 Electrical characteristics of the diodes . . . . . . . . . . . . . . . . . . . . . . . . . 162 6.7 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 7 Working Mechanism 167 7.1 Experimental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 7.2 Diode characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 7.3 Simulation and modeling of the diode characteristics . . . . . . . . . . . . . . . . . 173 7.4 Interpretation of the operation mechanism . . . . . . . . . . . . . . . . . . . . . . . 181 7.5 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 8 Optimization of VOTs 183 8.1 Misalignment of the electrodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 8.2 Use of doping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 8.3 Variation of the intrinsic layer thickness . . . . . . . . . . . . . . . . . . . . . . . . . 190 8.4 Structuring the active area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 8.5 High-frequency operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 8.6 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 9 Self-heating in organic semiconductors 209 9.1 Temperature activation in C60 triodes . . . . . . . . . . . . . . . . . . . . . . . . . . 210 9.2 nin-C60 crossbar structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 9.3 Thermal switching in organic semiconductors . . . . . . . . . . . . . . . . . . . . . 216 9.4 Self-heating in large area devices: Organic LEDs . . . . . . . . . . . . . . . . . . . 218 9.5 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10 Conclusion and Outlook 227 10.1 Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 10.2 Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 A Appendix 233 A.1 Appendix 1: Accuracy of the current gain . . . . . . . . . . . . . . . . . . . . . . . 233 A.2 Appendix 2: Fit of XRR measurements . . . . . . . . . . . . . . . . . . . . . . . . . 234 A.3 Appendix 3: Atomic force microscopy . . . . . . . . . . . . . . . . . . . . . . . . . 236 A.4 Appendix 4: Transmission electron microscopy . . . . . . . . . . . . . . . . . . . . 236 A.5 Appendix 5: Drift-diffusion simulation of nin devices . . . . . . . . . . . . . . . . . 239 A.6 Appendix 6: A simple parallel thermistor circuit . . . . . . . . . . . . . . . . . . . . 241 List of Figures 245 References 290In dieser Arbeit wird ein vertikaler organischer Transistor mit hoher Leistungsfähigkeit vorgestellt, der auf dem organischen Halbleiter C60 basiert. Die von organischen Leuchtdioden und organischen Solarzellen bekannte \'Sandwich’-Geometrie wird verwendet, so dass es möglich ist, für die vertikale Stromrichtung kurze Transferlängen der Ladungsträger zu erreichen. Im Vergleich zum konventionellen organischen Feldeffekttransistor mit lateralem Stromfluss werden dadurch viel kleinere Kanallängen erreicht, selbst wenn preisgünstige Schattenmasken mit geringer Auflösung für die thermische Verdampfung im Vakuum genutzt werden. Daher kann der Transistor bei einer Betriebsspannung von 1 V Stromdichten im Bereich von 10 A/cm² und Schaltgeschwindigkeiten im MHz-Bereich erreichen. Obwohl diese Technologie vielversprechend ist, fehlt bislang ein umfassendes Verständnis des Funktionsmechanismus. Hier wird gezeigt, dass der Transistor eine nanoporöse Basiselektrode hat, die durch ein natives Oxid auf ihrer Oberfläche elektrisch isoliert ist. Daher kann das Bauelement als zwei Metall-Oxid-Halbleiter-Dioden verstanden werden, die sich eine gemeinsame Elektrode, die Basis, teilen. Unter Spannung akkumulieren Ladungsträger vor dem Oxid, ähnlich zur Ausbildung eines Ladungsträgerkanals im Feldeffekttransistor. Aufgrund der erhöhten Leitfähigkeit in dieser Region werden Ladungsträger effizient zu und durch die Öffnungen der Basis transportiert, was zu hohen Ladungsträgertransmissionen führt. Selbst bei einer geringen Konzentration von Löchern in der Basiselektrode werden so hohe Transmissionsströme erzielt. Das Bauelementkonzept ist ideal für Anwendungen, in denen eine hohe Transkonduktanz und eine hohe Schaltgeschwindigkeit erreicht werden soll, z.B. in analogen Schaltkreisen, die kleine Signale verarbeiten. Das volle Potential des Transistors offenbart sich jedoch, wenn die aktive Fläche durch eine Isolatorschicht strukturiert wird, um den Überlapp der drei Elektroden zu optimieren, so dass Leckströme minimiert werden. Daneben ist die Dotierung der Molekülschichten am Emitter essentiell, um Kontaktwiderstände zu vermeiden. Aufgrund der hohen Leistungsdichten in den vertikalen C60-Transistoren kommt es zur Selbsterwärmung, die in dieser Arbeit im Kontext organischen Halbleiter diskutiert wird. Die große Aktivierungsenergie der Leitfähigkeit führt zu S-förmigen Strom-Spannungs-Kennlinien und hat thermisches Umschalten sowie negative differentielle Widerstände zur Folge, was für verschiedene Bauelemente demonstriert wird. Ein detailliertes Verständnis dieser Prozesse ist wichtig, um Beschränkungen für Anwendungen zu erkennen und um entsprechende Verbesserungen einzuführen.:CONTENTS Publications, patents and conference contributions 9 1 Introduction 13 2 Theory 19 2.1 From small molecules to conducting thin films . . . . . . . . . . . . . . . . . . . . 19 2.1.1 Aromatic hydrocarbons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.1.2 Solid state physics of molecular materials . . . . . . . . . . . . . . . . . . . 24 2.1.3 Energetic landscape of an organic semiconductor . . . . . . . . . . . . . . 26 2.1.4 Charge transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 2.2 Semiconductor structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 2.2.1 Semiconductor statistics and transport . . . . . . . . . . . . . . . . . . . . 42 2.2.2 Charge injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 2.2.3 Limitations of the current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2.2.4 Metal-oxide-semiconductor structures . . . . . . . . . . . . . . . . . . . . . 57 2.3 Self-heating theory of thermistor device . . . . . . . . . . . . . . . . . . . . . . . . 61 3 Organic transistors 65 3.1 The organic field-effect transistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 3.1.1 Basic principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 3.1.2 Device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 3.1.3 Device geometries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 3.1.4 Device parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 3.1.5 Issues of OFETs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 3.1.6 Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 3.2 Overview over vertical organic transistors . . . . . . . . . . . . . . . . . . . . . . . 76 3.2.1 VOTs with an unstructured base electrode . . . . . . . . . . . . . . . . . . . 76 3.2.2 VOTs with structured base electrode . . . . . . . . . . . . . . . . . . . . . . 79 3.2.3 Charge injection modulating transistors . . . . . . . . . . . . . . . . . . . . 82 3.2.4 Vertical organic field-effect transistor . . . . . . . . . . . . . . . . . . . . . . 85 3.2.5 Development of the scientific output . . . . . . . . . . . . . . . . . . . . . . 87 3.2.6 Competing technologies and approaches . . . . . . . . . . . . . . . . . . . 88 3.3 Vertical Organic Triodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.3.1 Stucture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.3.2 Electronic configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 3.3.3 Energetic alignment of the diodes . . . . . . . . . . . . . . . . . . . . . . . 92 3.3.4 Current flow in the on and the off-state . . . . . . . . . . . . . . . . . . . . 94 3.3.5 Definition and extraction of parameters . . . . . . . . . . . . . . . . . . . . 95 4 Experimental 101 4.1 General processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 4.1.1 Thermal vapor deposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 4.1.2 Processing tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 4.1.3 Processing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2 Mask setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 4.3 Measurement setups and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 4.3.1 Current-voltage measurements . . . . . . . . . . . . . . . . . . . . . . . . . 108 4.3.2 Frequency-dependent measurements . . . . . . . . . . . . . . . . . . . . . 108 4.3.3 Impedance Spectroscopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3.4 Ultraviolet and X-ray Photoelectron Spectroscopy . . . . . . . . . . . . . . . 110 4.3.5 Thermal imaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 4.4 Materials used in C60 triodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 4.4.1 Buckminsterfullerene C60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 4.4.2 Tungsten paddlewheel W2(hpp)4 . . . . . . . . . . . . . . . . . . . . . . . . 116 4.4.3 Aluminum and its oxides . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 4.4.4 Spiro-TTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 4.5 Materials used in Organic Light-emitting Diodes . . . . . . . . . . . . . . . . . . . 121 5 Introduction of C60 VOTs 123 5.1 Sample preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 5.2 Diode characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 5.3 Base sweep measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 5.4 Determination of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 5.5 Common-base connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.6 Output characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 5.7 Frequency-dependent measurement . . . . . . . . . . . . . . . . . . . . . . . . . . 137 5.8 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 6 Effect of annealing 141 6.1 Charge carrier transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 6.2 Sheet resistance and transmittance of the base electrode . . . . . . . . . . . . . . 142 6.3 Investigation of morphological changes . . . . . . . . . . . . . . . . . . . . . . . . 144 6.4 Photoelectron spectroscopy of the base electrode . . . . . . . . . . . . . . . . . . 153 6.5 Influence of air exposure and annealing onto the dopants . . . . . . . . . . . . . . 159 6.6 Electrical characteristics of the diodes . . . . . . . . . . . . . . . . . . . . . . . . . 162 6.7 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 7 Working Mechanism 167 7.1 Experimental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 7.2 Diode characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 7.3 Simulation and modeling of the diode characteristics . . . . . . . . . . . . . . . . . 173 7.4 Interpretation of the operation mechanism . . . . . . . . . . . . . . . . . . . . . . . 181 7.5 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 8 Optimization of VOTs 183 8.1 Misalignment of the electrodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 8.2 Use of doping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 8.3 Variation of the intrinsic layer thickness . . . . . . . . . . . . . . . . . . . . . . . . . 190 8.4 Structuring the active area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 8.5 High-frequency operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 8.6 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 9 Self-heating in organic semiconductors 209 9.1 Temperature activation in C60 triodes . . . . . . . . . . . . . . . . . . . . . . . . . . 210 9.2 nin-C60 crossbar structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 9.3 Thermal switching in organic semiconductors . . . . . . . . . . . . . . . . . . . . . 216 9.4 Self-heating in large area devices: Organic LEDs . . . . . . . . . . . . . . . . . . . 218 9.5 Intermediate summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 10 Conclusion and Outlook 227 10.1 Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 10.2 Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 A Appendix 233 A.1 Appendix 1: Accuracy of the current gain . . . . . . . . . . . . . . . . . . . . . . . 233 A.2 Appendix 2: Fit of XRR measurements . . . . . . . . . . . . . . . . . . . . . . . . . 234 A.3 Appendix 3: Atomic force microscopy . . . . . . . . . . . . .

Xray Generation by Field Emission

Since the discovery of X-rays over a century ago the techniques applied to the engineering of X-ray sources have remained relatively unchanged. From the inception of thermionic electron sources, which, due to simplicity of fabrication, remain central to almost all X-ray applications at this time, there have been few fundamental technological advances. The emergence of new materials and manufacturing techniques has created an opportunity to replace the traditional thermionic devices with those that incorporate Field Emission electron sources. One of the most important attributes of Field Emission X-ray sources is their controllability, and in particular the fast response time, which opens the door to applying techniques which have formerly been the preserve of optical systems. The work in this thesis attempts to bridge the gap between the fabrication and optimisation of the vacuum electronic devices and image processing aspects of a new approach to high speed radiographic imaging, particularly with a view to addressing practical real-world problems. Off the back of a specific targeted application, the project has involved the design of a viable field emission X-ray source, together with the development of an understanding of the failure modes in such devices, both by analysis and by simulation. This thesis reviews the capabilities and the requirements of X-ray sources, the methods by which nano-materials may be applied to the design of those devices and the improvements and attributes that can be foreseen. I study the image processing methods that can exploit these attributes, and investigate the performance of X-ray sources based upon electron emitters using carbon nanotubes. Modelling of the field emission and electron trajectories of the cathode assemblies has led me to the design of equipment to evaluate and optimise the parameters of an X-ray tube, which I have used to understand the performance that is achievable. Finally, I draw conclusions from this work and outline the next steps to provide the basis for a commercial solution

USE OF HIGH SURFACE NANOFIBROUS MATERIALS IN MEDICINE

n/

Integrated Circuits/Microchips

With the world marching inexorably towards the fourth industrial revolution (IR 4.0), one is now embracing lives with artificial intelligence (AI), the Internet of Things (IoTs), virtual reality (VR) and 5G technology. Wherever we are, whatever we are doing, there are electronic devices that we rely indispensably on. While some of these technologies, such as those fueled with smart, autonomous systems, are seemingly precocious; others have existed for quite a while. These devices range from simple home appliances, entertainment media to complex aeronautical instruments. Clearly, the daily lives of mankind today are interwoven seamlessly with electronics. Surprising as it may seem, the cornerstone that empowers these electronic devices is nothing more than a mere diminutive semiconductor cube block. More colloquially referred to as the Very-Large-Scale-Integration (VLSI) chip or an integrated circuit (IC) chip or simply a microchip, this semiconductor cube block, approximately the size of a grain of rice, is composed of millions to billions of transistors. The transistors are interconnected in such a way that allows electrical circuitries for certain applications to be realized. Some of these chips serve specific permanent applications and are known as Application Specific Integrated Circuits (ASICS); while, others are computing processors which could be programmed for diverse applications. The computer processor, together with its supporting hardware and user interfaces, is known as an embedded system.In this book, a variety of topics related to microchips are extensively illustrated. The topics encompass the physics of the microchip device, as well as its design methods and applications

Ordered Nanomaterials for Electron Field Emission

In the quest for reliable, repeatable and stable field electron emission that has commercial potential, whilst many attempts have been made, none yet has been truly distinguishable as being successful. Whilst I do not claim within this thesis to have uncovered the secret to success, fundamental issues have been addressed that concern the future directions towards achieving its full potential. An exhaustive comparison is made across the diverse range of materials that have, over the past 40-50 years, been postulated and indeed tested as field emitters. This has not previously been attempted. The materials are assessed according to the important metrics of turn on voltage, Eon, and maximum current density, Jmax, where low Eon and high Jmax are seen as desirable. The nano-carbons, carbon nanotubes (CNTs), in particular, perform well in both these metrics. No dependency was seen between the material work function and its performance as an emitter, which might have been suggested by the Fowler Nordheim equations. To address the issues underlying the definition of the local enhancement factor, β, a number of variations of surface geometry using CNTs were fabricated. The field emission of these emitters was measured using two different approaches. The first is a Scanning Electrode Field Emission Microscope, SAFEM, which maps the emission at individual locations across the surface of the emitter, and the parallel plate that is more commonly encountered in field emission measurements. Finally, an observed hysteretic behaviour in CNT field emission was explored. The field emitters were subjected to a number of tests. These included; in-situ residual gas analysis of the gas species in the emitter environment, a stability study in which the emitters were exposed to a continuing voltage loop for 50 cycles, differing applied voltage times to analyse the effects on the emitted current, and varying maximums of applied field in a search for hysteresis onset information. These studies revealed the candidate in causing the hysteresis is likely to be water vapour that adsorbs on the CNT surface. A six step model if the emission process was made that details how and when the hysteresis is caused

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Development of a Low-Current Plasma-Based Cathode using the Emitter Material C12A7 Electride for Space Applications

Efficient electron sources are crucial for any space-based mission, especially when using electric thrusters. In many respects, hollow cathodes are a baseline technology due to their power-efficient electron emission in the desired current range and the potentially long lifetime of these emitters. However, the delicate design of the heater, with the associated constraints on its operation, and the high degradation of state-of-the-art materials to new propellant options under evaluation for electric space propulsion systems, are severe limitations of current systems. To address some of the most pressing challenges with cathodes, a heaterless plasma-based cathode using the emitter material C12A7 electride has been developed and is described in this thesis. The cathode has been developed with the requirements of an electrodynamic tether demonstration mission in mind. C12A7 electride is an electrically conductive ceramic that has recently attracted much attention as a potential electron emitter in hollow cathodes. However, there appear to be significant challenges with the material itself, requiring careful design evaluation and thorough testing to gain a sufficient understanding of the material's behavior. Most importantly, material degradation in the harsh environment of a plasma. Throughout the thesis, an optimized electride material was developed and tested, yielding a ceramic-metal composite with greatly improved plasma performance compared to pure C12A7 electride material. In addition, a special design of a plasma-based cathode was developed and described, which respects the unique properties of the material and allows convenient operation, and thus characterization and optimization of the cathode. Several milestones have been achieved, including endurance operation for nearly \num{1000} hours, successful operation with a Hall-effect thruster, characterization of the cathode in the discharge current range of \qtyrange{0.2}{2}{\A}, reduction of the flow rate required for ignition and operation down to \qty{2}{\sccm}, and heaterless ignition cycling for up to \num{3300} cycles with a single insert. The observed performance of the cathode was eventually compared with performance data reported in the literature using state-of-the-art materials and showed reasonable comparability. In particular, advantages over state-of-the-art cathodes were identified in terms of ignition behavior: Requiring only \qty{2}{\sccm} of krypton and a potential of less than \qty{400}{\V}, and reaching steady-state operation in less than a few tens of milliseconds, the performance was better than reported in the literature. Combined with the acceptable discharge performance, these results motivate the further development of such an electride cathode for space applications. Due to the simplicity of such a cathode, applications for a wide range of industrial processes may also be considered.:1 - Introduction 2 - Cathode Theory 3 - C12A7 Electride 4 - Scope of Development 5 - Design Development 6 - Thruster Operation 7 - Endurance Operation 8 - Electride Cathode for Low Current EDT Operation 9 - Additional Tests with the Electride Cathode 10 - Discussion of Results and Further Steps 11 - Conclusion Bibliography Appendi

???????????? ?????? ?????? ????????? ?????? : ?????? ??? ?????? ??????

Department of PhysicsThe outstanding properties of graphene have enabled to reveal the exotic carrier transport behavior approaching to the relativistic quantum mechanics, act as the excellent diffusion barrier protecting the junction interface from the material intermixing by atomic diffusion, serve as the effective interlayer modulating the electronic states, and offer the promising solid-state platform allowing the quantum optics of the Dirac Fermion. In this dissertaion, the ballistic carrier transport through graphene in two different aspects will be covered. Understanding of vertical transport across graphene-combined hetero-junction and lateral transport in the graphene channel is the main agenda. The sensitive manipulation of electronic states at/across the interface and the controllable distribution of electric potential on the surface can lead to an extraordinary physical phenomenon and conductance switching. Based on that, it is eventually proposed that how the brand-new type graphene-based device can be evolved or what kind of method can be adapted to improve the actual performance of the graphene-based devices significantly regardless of property or quality of graphene.clos