UWB system based on gain-switched laser

Simulation results based on an UltraWideBand (UWB) system employing a gain-switched laser are presented. 156 Mb/s data stream modulates the position of short electrical pulses, which are then used to gain-switch the laser. The output optical pulses are then transmitted over fiber to a Remote Antenna Unit (RAU), where the signal is detected and undergoes spectral shaping (according to UWB requirements). The resulting Pulse Position Modulated (PPM) electrical impulses are then converted to an amplitude-modulated signal and down-converted. Bit Error Rate measurements are carried out on a back-to-back system and a transmission link (over different lengths of fiber

Experimental Investigation Of Ultrawideband Wireless Systems: Waveform Generation, Propagation Estimation, And Dispersion Compensation

Ultrawideband (UWB) is an emerging technology for the future high-speed wireless communication systems. Although this technology offers several unique advantages like robustness to fading, large channel capacity and strong anti-jamming ability, there are a number of practical challenges which are topics of current research. One key challenge is the increased multipath dispersion which results because of the fine temporal resolution. The received response consists of different components, which have certain delays and attenuations due to the paths they took in their propagation from the transmitter to the receiver. Although such challenges have been investigated to some extent, they have not been fully explored in connection with sophisticated transmit beamforming techniques in realistic multipath environments. The work presented here spans three main aspects of UWB systems including waveform generation, propagation estimation, and dispersion compensation. We assess the accuracy of the measured impulse responses extracted from the spread spectrum channel sounding over a frequency band spanning 2-12 GHz. Based on the measured responses, different transmit beamforming techniques are investigated to achieve high-speed data transmission in rich multipath channels. We extend our work to multiple antenna systems and implement the first experimental test-bed to investigate practical challenges such as imperfect channel estimation or coherency between the multiple transmitters over the full UWB band. Finally, we introduce a new microwave photonic arbitrary waveform generation technique to demonstrate the first optical-wireless transmitter system for both characterizing channel dispersion and generating predistorted waveforms to achieve spatio-temporal focusing through the multipath channels

2009 Index IEEE Antennas and Wireless Propagation Letters Vol. 8

This index covers all technical items - papers, correspondence, reviews, etc. - that appeared in this periodical during the year, and items from previous years that were commented upon or corrected in this year. Departments and other items may also be covered if they have been judged to have archival value. The Author Index contains the primary entry for each item, listed under the first author\u27s name. The primary entry includes the coauthors\u27 names, the title of the paper or other item, and its location, specified by the publication abbreviation, year, month, and inclusive pagination. The Subject Index contains entries describing the item under all appropriate subject headings, plus the first author\u27s name, the publication abbreviation, month, and year, and inclusive pages. Note that the item title is found only under the primary entry in the Author Index

2008 Index IEEE Transactions on Control Systems Technology Vol. 16

This index covers all technical items - papers, correspondence, reviews, etc. - that appeared in this periodical during the year, and items from previous years that were commented upon or corrected in this year. Departments and other items may also be covered if they have been judged to have archival value. The Author Index contains the primary entry for each item, listed under the first author\u27s name. The primary entry includes the coauthors\u27 names, the title of the paper or other item, and its location, specified by the publication abbreviation, year, month, and inclusive pagination. The Subject Index contains entries describing the item under all appropriate subject headings, plus the first author\u27s name, the publication abbreviation, month, and year, and inclusive pages. Note that the item title is found only under the primary entry in the Author Index

Interference mitigation and awareness for improved reliability

Wireless systems are commonly affected by interference from various sources. For example, a number of users that operate in the same wireless network can result in multiple-access interference (MAI). In addition, for ultrawideband (UWB) systems, which operate at very low power spectral densities, strong narrowband interference (NBI) can have significant effects on the communications reliability. Therefore, interference mitigation and awareness are crucial in order to realize reliable communications systems. In this chapter, pulse-based UWB systems are considered, and the mitigation of MAI is investigated first. Then, NBI avoidance and cancelation are studied for UWB systems. Finally, interference awareness is discussed for short-rate communications, next-generation wireless networks, and cognitive radios.Mitigation of multiple-access interference (MAI)In an impulse radio ultrawideband (IR-UWB) communications system, pulses with very short durations, commonly less than one nanosecond, are transmitted with a low-duty cycle, and information is carried by the positions or the polarities of pulses [1-5]. Each pulse resides in an interval called frame, and the positions of pulses within frames are determined according to time-hopping (TH) sequences specific to each user. The low-duty cycle structure together with TH sequences provide a multiple-access capability for IR-UWB systems [6].Although IR-UWB systems can theoretically accommodate a large number of users in a multiple-access environment [2, 4], advanced signal processing techniques are necessary in practice in order to mitigate the effects of interfering users on the detection of information symbols efficiently [6]. © Cambridge University Press 2011

Optical frequency up-conversion of UWB monocycle pulse based on pulsed-pump fiber optical parametric amplifier

Optical Transmission Systems, Switching, and Subsystems VII, 2009; Asia Communications and Photonics Conference and Exhibition, ACP, 2009We propose a method to realize frequency up-conversion of UWB monocycle pulse using pulsed-pump fiber optical parametric amplifier (OPA). The spectrum of the amplified signal contains many discrete frequency components which are separated by the modulation frequency of the pump. Each frequency components contain the same spectral information as that of the original signal. By selecting the first-order or higher-order frequency components of the amplified signal and beating in the photodetector, up-converted signal at different frequencies are obtained. We demonstrate frequency up-conversion of baseband UWB monocycle pulse from 3-GHz to 19-GHz in the experiment and frequency up-conversion of pseudo-random binary sequence (PRBS) signal from 3-GHz to 60-GHz in the simulation. © 2009 SPIE-OSA-IEEE.published_or_final_versio

Radio over fibre distribution systems for ultra-wide band and millimetre wave applications

Short range wireless technology such as ultra-wideband (UWB) and 60 GHz millimetre wave (mm-wave) play a key role for wireless connectivity in indoor home, office environment or large enclosed public areas. UWB has been allocated at the frequency band 3.1-10.6 GHz with an emission power below -41.3 dBm. Mm-wave signals around 60 GHz have also attracted much attention to support high-speed data for short range wireless applications. The wide bandwidth and high allowable transmit power at 60 GHz enable multi-Gbps wireless transmission over typical indoor distances. Radio-over-fibre (RoF) systems are used to extend the propagation distance of both UWB and mm-wave signals over hundred of meters inside a building. UWB or mm-wave signals over fibre can be generated first at the central office before being distributed to the remote access points through optical fibre. In this work, we investigate two new techniques to generate and distribute UWB signals. These techniques are based on generating Gaussian pulse position modulation (PPM) using a gain switched laser (GSL). The simulation and experimental results have been carried out to show the suitability of employing gain switching in UWB over fibre systems (UWBoF) to develop a reliable, simple, and low cost technique for distributing UWB pulses. The second part of this work proposes two configurations for optical mm-wave generation and transmission of 3 Gbps downstream data based on GSL. We investigate the distribution of these two methods over fibre with wireless link, and demonstrate the system simplicity and cost efficiency for mm-wave over fibre systems. Both configurations are simulated to verify our obtained results and show system performance at higher bit rates. In the third part, we generate phase modulated mm-waves by using an external injection of a modulated light source into GSL. The performance of this system is experimentally investigated and simulated for different fiber links

Detection of PPM-UWB random signals

This paper focuses on the symbol detection problem of random pulse-position modulation (PPM) ultrawideband (UWB) signals in the absence of interframe interference. Particular attention is devoted to severely time-varying channels where optimal detectors are proposed for both uncorrelated and correlated scattering scenarios. This is done by assuming the received waveforms to be unknown parameters. In UWB communication systems, the assumption of unknown random waveforms is consistent with the fact that the received waveform has very little resemblance with the original transmitted pulse. In order to circumvent this limitation, a conditional approach is presented herein by compressing the likelihood ratio test with the information regarding the second-order moments of the end-to-end channel response. Both full-rank and rank-one detectors are derived. For the reduced complexity rank-one detector, an iterative procedure is presented that maximizes the J-divergence between the hypotheses to be tested. Finally, simulation results are provided to compare the performance of the proposed detectors in different propagation environments.Peer Reviewe

Effect and Compensation of Timing Jitter in Through-Wall Human Indication via Impulse Through-Wall Radar

Impulse through-wall radar (TWR) is considered as one of preferred choices for through-wall human indication due to its good penetration and high range resolution. Large bandwidth available for impulse TWR results in high range resolution, but also brings an atypical adversity issue not substantial in narrowband radars — high timing jitter effect, caused by the non-ideal sampling clock at the receiver. The fact that impulse TWR employs very narrow pulses makes little jitter inaccuracy large enough to destroy the signal correlation property and then degrade clutter suppression performance. In this paper, we focus on the timing jitter impact on clutter suppression in through-wall human indication via impulse TWR. We setup a simple timing jitter model and propose a criterion namely average range profile (ARP) contrast is to evaluate the jitter level. To combat timing jitter, we also develop an effective compensation method based on local ARP contrast maximization. The proposed method can be implemented pulse by pulse followed by exponential average background subtraction algorithm to mitigate clutters. Through-wall experiments demonstrate that the proposed method can dramatically improve through-wall human indication performance