32 research outputs found
Synchronization for Impulse-Radio UWB With Energy-Detection and Multi-User Interference: Algorithms and Application to IEEE 802.15.4a
Energy-detection (ED) receivers can take advantage of the ranging and multipath resistance capabilities of impulse-radio ultra-wideband (IR-UWB) physical layers at a much lower complexity than coherent receivers. However, ED receivers are extremely vulnerable to multi-user interference (MUI). Therefore, the design of IR-UWB ED architectures must take MUI into account. In this paper, we present the design and evaluation of two complementary algorithms for reliable and robust synchronization of IR-UWB ED receivers in the presence of MUI: 1) power-independent detection and preamble code interference cancellation (PICNIC) and 2) detection of start-frame-delimiter through sequential ratio tests (DESSERT). PICNIC addresses packet detection and timing acquisition while DESSERT focuses on start-frame-delimiter (SFD) detection. Both algorithms are evaluated with the IEEE 802.15.4a IR-UWB physical layer, standardized for low data-rate networks. The performance evaluation with extensive simulations show that our algorithms outperform nonrobust synchronization algorithms by up to two orders of magnitude in the presence of MUI
Chaos-based TOA estimator for DS-UWB ranging systems in multiuser environment
International audienceIn this paper, we present a chaos-based decoupled multiuser ranging (DEMR) estimator for multiuser DS-UWB ranging system. In the DEMR estimator, users are decoupled by the knowledge of all the users' limited number of data bits. Then, the ranging performance of each user mainly depends on the non-cyclic autocorrelation property of the spreading code. Based on this property, we improve DEMR estimator by using the selected binary chaotic sequences instead of the Gold sequences in order to increase the system capacity and to improve the ranging accuracy. Simulations in CM1 channel show that the chaos-based DEMR estimator is quite near-far resistant and achieves a noticeable ranging accuracy even in a heavily loaded system. Compared with using Gold sequences, chaos-based DEMR not only works with more users than full load of Gold sequences but also improves the ranging accuracy especially under low SNR condition
Clock-Offset Tracking Software Algorithms For IR-UWB Energy-Detection Receivers
We present a clock-offset tracking algorithm for impulse-radio ultra-wide band (IR-UWB) energy-detection receivers. There is a complexity versus performance trade-off for the design of IR-UWB energy-detection receivers: Extremely low-complexity energy-detection receivers are built with a large, constant integration duration; they are robust to clock drifts but are sensitive to noise enhancement effects and cannot adapt to channel variations. More sophisticated energy-detection receivers use a shorter integration duration and combine several weighted outputs of the energy collector; they are robust to noise enhancement effects, can adapt to channel variations and offer a much better performance than non-adaptive receivers. However, they become sensitive to clock offsets. Hence, there is a need for low-complexity clock-offset tracking solutions to support adaptive energy-detection receivers. Our solution is constructed around the Radon transform, an image processing tool traditionally used to detect line features in images. Our solution is fully compatible with the IEEE 802.15.4a standard, does not increase the hardware complexity of the receiver and reduces the performance loss due to clock offset to less than 0.5 dB
Ultra Wideband Communications: from Analog to Digital
ï»żUltrabreitband-Signale (Ultra Wideband [UWB]) können einen
signifikanten Nutzen im Bereich drahtloser Kommunikationssysteme haben. Es
sind jedoch noch einige Probleme offen, die durch Systemdesigner und
Wissenschaftler gelöst werden mĂŒssen. Ein Funknetzsystem mit einer derart
groĂen Bandbreite ist normalerweise auch durch eine groĂe Anzahl an
Mehrwegekomponenten mit jeweils verschiedenen Pfadamplituden
gekennzeichnet. Daher ist es schwierig, die zeitlich verteilte Energie
effektiv zu erfassen. AuĂerdem ist in vielen FĂ€llen der naheliegende
Ansatz, ein kohÀrenter EmpfÀnger im Sinne eines signalangepassten Filters
oder eines Korrelators, nicht unbedingt die beste Wahl. In der vorliegenden
Arbeit wird dabei auf die bestehende Problematik und weitere
Lösungsmöglichkeiten eingegangen.
Im ersten Abschnitt geht es um âImpulse Radio UWBâ-Systeme mit
niedriger Datenrate. Bei diesen Systemen kommt ein inkohÀrenter EmpfÀnger
zum Einsatz. InkohÀrente Signaldetektion stellt insofern einen
vielversprechenden Ansatz dar, als das damit aufwandsgĂŒnstige und robuste
Implementierungen möglich sind. Dies trifft vor allem in AnwendungsfÀllen
wie den von drahtlosen Sensornetzen zu, wo preiswerte GerÀte mit langer
Batterielaufzeit nötigsind. Dies verringert den fĂŒr die KanalschĂ€tzung
und die Synchronisation nötigen Aufwand, was jedoch auf Kosten der
Leistungseffizienz geht und eine erhöhte Störempfindlichkeit gegenĂŒber
Interferenz (z.B. Interferenz durch mehrere Nutzer oder schmalbandige
Interferenz) zur Folge hat.
Um die Bitfehlerrate der oben genannten Verfahren zu bestimmen, wurde
zunÀchst ein inkohÀrenter Combining-Verlust spezifiziert, welcher
auftritt im Gegensatz zu kohÀrenter Detektion mit Maximum Ratio Multipath
Combining. Dieser Verlust hÀngt von dem Produkt aus der LÀnge des
Integrationsfensters und der Signalbandbreite ab.
Um den Verlust durch inkohÀrentes Combining zu reduzieren und somit die
Leistungseffizienz des EmpfÀngers zu steigern, werden verbesserte
Combining-Methoden fĂŒr Mehrwegeempfang vorgeschlagen. Ein analoger
EmpfÀnger, bei dem der Hauptteil des Mehrwege-Combinings durch einen
âIntegrate and Dumpâ-Filter implementiert ist, wird fĂŒr UWB-Systeme
mit Zeit-Hopping gezeigt. Dabei wurde die Einsatzmöglichkeit von dĂŒnn
besetzten Codes in solchen System diskutiert und bewertet. Des Weiteren
wird eine Regel fĂŒr die Code-Auswahl vorgestellt, welche die StabilitĂ€t
des Systems gegen Mehrnutzer-Störungen sicherstellt und gleichzeitig den
Verlust durch inkohÀrentes Combining verringert.
Danach liegt der Fokus auf digitalen Lösungen bei inkohÀrenter
Demodulation. Im Vergleich zum AnalogempfÀnger besitzt ein
DigitalempfÀnger einen Analog-Digital-Wandler im Zeitbereich gefolgt von
einem digitalen Optimalfilter. Der digitale Optimalfilter dekodiert den
Mehrfachzugriffscode kohÀrent und beschrÀnkt das inkohÀrente Combining
auf die empfangenen Mehrwegekomponenten im Digitalbereich. Es kommt ein
schneller Analog-Digital-Wandler mit geringer Auflösung zum Einsatz, um
einen vertretbaren Energieverbrauch zu gewÀhrleisten. Diese Digitaltechnik
macht den Einsatz langer Analogverzögerungen bei differentieller
Demodulation unnötig und ermöglicht viele Arten der digitalen
Signalverarbeitung. Im Vergleich zur Analogtechnik reduziert sie nicht nur
den inkohÀrenten Combining-Verlust, sonder zeigt auch eine stÀrkere
Resistenz gegenĂŒber Störungen. Dabei werden die Auswirkungen der
Auflösung und der Abtastrate der Analog-Digital-Umsetzung analysiert. Die
Resultate zeigen, dass die verminderte Effizienz solcher
Analog-Digital-Wandler gering ausfÀllt. Weiterhin zeigt sich, dass im
Falle starker Mehrnutzerinterferenz sogar eine Verbesserung der Ergebnisse
zu beobachten ist. Die vorgeschlagenen Design-Regeln spezifizieren die
Anwendung der Analog-Digital-Wandler und die Auswahl der Systemparameter in
AbhÀngigkeit der verwendeten Mehrfachzugriffscodes und der Modulationsart.
Wir zeigen, wie unter Anwendung erweiterter Modulationsverfahren die
Leistungseffizienz verbessert werden kann und schlagen ein Verfahren zur
UnterdrĂŒckung schmalbandiger Störer vor, welches auf Soft Limiting
aufbaut. Durch die Untersuchungen und Ergebnissen zeigt sich, dass
inkohÀrente EmpfÀnger in UWB-Kommunikationssystemen mit niedriger
Datenrate ein groĂes Potential aufweisen.
AuĂerdem wird die Auswahl der benutzbaren Bandbreite untersucht, um einen
Kompromiss zwischen inkohÀrentem Combining-Verlust und StabilitÀt
gegenĂŒber langsamen Schwund zu erreichen. Dadurch wurde ein neues Konzept
fĂŒr UWB-Systeme erarbeitet: wahlweise kohĂ€rente oder inkohĂ€rente
EmpfÀnger, welche als UWB-Systeme Frequenz-Hopping nutzen. Der wesentliche
Vorteil hiervon liegt darin, dass die Bandbreite im Basisband sich deutlich
verringert. Mithin ermöglicht dies einfach zu realisierende digitale
Signalverarbeitungstechnik mit kostengĂŒnstigen Analog-Digital-Wandlern.
Dies stellt eine neue Epoche in der Forschung im Bereich drahtloser
Sensorfunknetze dar.
Der Schwerpunkt des zweiten Abschnitts stellt adaptiven Signalverarbeitung
fĂŒr hohe Datenraten mit âDirect Sequenceâ-UWB-Systemen in den
Vordergrund. In solchen Systemen entstehen, wegen der groĂen Anzahl der
empfangenen Mehrwegekomponenten, starke Inter- bzw.
Intrasymbolinterferenzen. AuĂerdem kann die FunktionalitĂ€t des Systems
durch Mehrnutzerinterferenz und Schmalbandstörungen deutlich beeinflusst
werden. Um sie zu eliminieren, wird die âWidely Linearâ-Rangreduzierung
benutzt. Dabei verbessert die Rangreduzierungsmethode das
Konvergenzverhalten, besonders wenn der gegebene Vektor eine sehr groĂe
Anzahl an Abtastwerten beinhaltet (in Folge hoher einer Abtastrate).
ZusÀtzlich kann das System durch die Anwendung der R-linearen Verarbeitung
die Statistik zweiter Ordnung des nicht-zirkularen Signals vollstÀndig
ausnutzen, was sich in verbesserten SchÀtzergebnissen widerspiegelt.
Allgemeine kann die Methode der âWidely Linearâ-Rangreduzierung auch in
andern Bereichen angewendet werden, z.B. in âDirect
Sequenceâ-Codemultiplexverfahren (DS-CDMA), im MIMO-Bereich, im Global
System for Mobile Communications (GSM) und beim Beamforming.The aim of this thesis is to investigate key issues encountered in the
design of transmission schemes and receiving techniques for Ultra Wideband
(UWB) communication systems. Based on different data rate applications,
this work is divided into two parts, where energy efficient and robust
physical layer solutions are proposed, respectively.
Due to a huge bandwidth of UWB signals, a considerable amount of multipath
arrivals with various path gains is resolvable at the receiver. For low
data rate impulse radio UWB systems, suboptimal non-coherent detection is a
simple way to effectively capture the multipath energy. Feasible techniques
that increase the power efficiency and the interference robustness of
non-coherent detection need to be investigated. For high data rate direct
sequence UWB systems, a large number of multipath arrivals results in
severe inter-/intra-symbol interference. Additionally, the system
performance may also be deteriorated by multi-user interference and
narrowband interference. It is necessary to develop advanced signal
processing techniques at the receiver to suppress these interferences.
Part I of this thesis deals with the co-design of signaling schemes and
receiver architectures in low data rate impulse radio UWB systems based on
non-coherent detection.â We analyze the bit error rate performance of
non-coherent detection and characterize a non-coherent combining loss,
i.e., a performance penalty with respect to coherent detection with maximum
ratio multipath combining. The thorough analysis of this loss is very
helpful for the design of transmission schemes and receive techniques
innon-coherent UWB communication systems.â We propose to use optical
orthogonal codes in a time hopping impulse radio UWB system based on an
analog non-coherent receiver. The âanalogâ means that the major part of
the multipath combining is implemented by an integrate and dump filter. The
introduced semi-analytical method can help us to easily select the time
hopping codes to ensure the robustness against the multi-user interference
and meanwhile to alleviate the non-coherent combining loss.â The main
contribution of Part I is the proposal of applying fully digital solutions
in non-coherent detection. The proposed digital non-coherent receiver is
based on a time domain analog-to-digital converter, which has a high speed
but a very low resolution to maintain a reasonable power consumption.
Compared to its analog counterpart, itnot only significantly reduces the
non-coherent combining loss but also offers a higher interference
robustness. In particular, the one-bit receiver can effectively suppress
strong multi-user interference and is thus advantageous in separating
simultaneously operating piconets.The fully digital solutions overcome the
difficulty of implementing long analog delay lines and make differential
UWB detection possible. They also facilitate the development of various
digital signal processing techniques such as multi-user detection and
non-coherent multipath combining methods as well as the use of advanced
modulationschemes (e.g., M-ary Walsh modulation).â Furthermore, we
present a novel impulse radio UWB system based on frequency hopping, where
both coherent and non-coherent receivers can be adopted. The key advantage
is that the baseband bandwidth can be considerably reduced (e.g., lower
than 500 MHz), which enables low-complexity implementation of the fully
digital solutions. It opens up various research activities in the
application field of wireless sensor networks.
Part II of this thesis proposes adaptive widely linear reduced-rank
techniques to suppress interferences for high data rate direct sequence UWB
systems, where second-order non-circular signals are used. The reduced-rank
techniques are designed to improve the convergence performance and the
interference robustness especially when the received vector contains a
large number of samples (due to a high sampling rate in UWB systems). The
widely linear processing takes full advantage of the second-order
statistics of the non-circular signals and enhances the estimation
performance. The generic widely linear reduced-rank concept also has a
great potential in the applications of other systems such as Direct
Sequence Code Division Multiple Access (DS-CDMA), Multiple Input Multiple
Output (MIMO) system, and Global System for Mobile Communications (GSM), or
in other areas such as beamforming
Cognitive-radio systems for spectrum, location, and environmental awareness
In order to perform reliable communications, a system needs to have sufficient information about its operational environment, such as spectral resources and propagation characteristics. Cognitive-radio technology has capabilities for acquiring accurate spectrum, location, and environmental information, due to its unique features such as spectrum, location, and environmental awareness. The goal of this paper is to give a comprehensive review of the implementation of these concepts. In addition, the dynamic nature of cognitive-radio systems - including dynamic spectrum utilization, transmission, the propagation channel, and reception - is discussed, along with performance limits, challenges, mitigation techniques, and open issues. The capabilities of cognitive-radio systems for accurate characterization of operational environments are emphasized. These are crucial for efficient communications, localization, and radar systems. © 2010 IEEE