Satellite-matrix-switched, time-division-multiple-access network simulator

A versatile experimental Ka-band network simulator has been implemented at the NASA Lewis Research Center to demonstrate and evaluate a satellite-matrix-switched, time-division-multiple-access (SMS-TDMA) network and to evaluate future digital ground terminals and radiofrequency (RF) components. The simulator was implemented by using proof-of-concept RF components developed under NASA contracts and digital ground terminal and link simulation hardware developed at Lewis. This simulator provides many unique capabilities such as satellite range delay and variation simulation and rain fade simulation. All network parameters (e.g., signal-to-noise ratio, satellite range variation rate, burst density, and rain fade) are controlled and monitored by a central computer. The simulator is presently configured as a three-ground-terminal SMS-TDMA network

Time division radio relay synchronizing system using different sync code words for in sync and out of sync conditions Patent

Time division relay synchronizer with master sync pulse for activating binary counter to produce signal identifying time slot for statio

Experiments applications guide: Advanced Communications Technology Satellite (ACTS)

This applications guide first surveys the capabilities of the Advanced Communication Technology Satellite (ACTS) system (both the flight and ground segments). This overview is followed by a description of the baseband processor (BBP) and microwave switch matrix (MSM) operating modes. Terminals operating with the baseband processor are referred to as low burst rate (LBR); and those operating with the microwave switch matrix, as high burst rate (HBR). Three very small-aperture terminals (VSATs), LBR-1, LBR-2, and HBR, are described for various ACTS operating modes. Also described is the NASA Lewis link evaluation terminal. A section on ACTS experiment opportunities introduces a wide spectrum of network control, telecommunications, system, and scientific experiments. The performance of the VSATs is discussed in detail. This guide is intended as a catalyst to encourage participation by the telecommunications, business, and science communities in a broad spectrum of experiments

Development and evaluation of a fault-tolerant multiprocessor (FTMP) computer. Volume 4: FTMP executive summary

The FTMP architecture is a high reliability computer concept modeled after a homogeneous multiprocessor architecture. Elements of the FTMP are operated in tight synchronism with one another and hardware fault-detection and fault-masking is provided which is transparent to the software. Operating system design and user software design is thus greatly simplified. Performance of the FTMP is also comparable to that of a simplex equivalent due to the efficiency of fault handling hardware. The FTMP project constructed an engineering module of the FTMP, programmed the machine and extensively tested the architecture through fault injection and other stress testing. This testing confirmed the soundness of the FTMP concepts

Distributed multi-user MIMO transmission using real-time sigma-delta-over-fiber for next generation fronthaul interface

To achieve the massive device connectivity and high data rate demanded by 5G, wireless transmission with wider signal bandwidths and higher-order multiple-input multiple-output (MIMO) is inevitable. This work demonstrates a possible function split option for the next generation fronthaul interface (NGFI). The proof-of-concept downlink architecture consists of real-time sigma-delta modulated signal over fiber (SDoF) links in combination with distributed multi-user (MU) MIMO transmission. The setup is fully implemented using off-the-shelf and in-house developed components. A single SDoF link achieves an error vector magnitude (EVM) of 3.14% for a 163.84 MHz-bandwidth 256-QAM OFDM signal (958.64 Mbps) with a carrier frequency around 3.5 GHz transmitted over 100 m OM4 multi-mode fiber at 850 nm using a commercial QSFP module. The centralized architecture of the proposed setup introduces no frequency asynchronism among remote radio units. For most cases, the 2 x 2 MU-MIMO transmission has little performance degradation compared to SISO, 0.8 dB EVM degradation for 40.96 MHz-bandwidth signals and 1.4 dB for 163.84 MHz-bandwidth on average, implying that the wireless spectral efficiency almost doubles by exploiting spatial multiplexing. A 1.4 Gbps data rate (720 Mbps per user, 163.84 MHz-bandwidth, 64-QAM) is reached with an average EVM of 6.66%. The performance shows that this approach is feasible for the high-capacity hot-spot scenario

Modular Home Automation Systems for Senior Citizens

The aging of the population is one of the biggest challenges in our society. Citizens life expectancy is growing and the birth rate is decreasing. In long-term this is untenable. Thanks to the advance of technology we can try to help to reduce the impact of this problem. I introduce a brief work on Modular Home Automation Systems with energy efficiency adapted to nowadays lifestyle and technology. These systems make use of wireless communications instead of wired ones to minimize the invasion of new devices. Because of the characteristics of these systems, ZigBee suits perfectly. ZigBee is a specification made to provide low rate wireless communications. ZigBee networks make the communication more efficient and adaptive. To achieve a modular environment, we use some design patterns from Software Engineering ,which also improve the security and maintainability of the system. The system is also expandable and reliable among other capabilities

Design of a simulation platform to test next generation of terrestrial DVB

Digital Terrestrial Television Broadcasting (DTTB) is a member of our daily life routine, and nonetheless, according to new users’ necessities in the fields of communications and leisure, new challenges are coming up. Moreover, the current Standard is not able to satisfy all the potential requirements. For that reason, first of all, a review of the current Standard has been performed within this work. Then, it has been identified the needing of developing a new version of the standard, ready to support enhanced services, as for example broadcasting transmissions to moving terminals or High Definition Television (HDTV) transmissions, among others. The main objective of this project is the design and development of a physical layer simulator of the whole DVB-T standard, including both the complete transmission and reception procedures. The simulator has been developed in Matlab. A detailed description of the simulator both from a functional and an architectural point of view is included. The simulator is the base for testing any possible modifications that may be included into the DVB-T2 future standard. In fact, several proposed enhancements have already been carried out and their performance has been evaluated. Specifically, the use of higher order modulation schemes, and the corresponding modifications in all the system blocks, have been included and evaluated. Furthermore, the simulator will allow testing other enhancements as the use of more efficient encoders and interleavers, MIMO technologies, and so on. A complete set of numerical results showing the performance of the different parts of the system, are presented in order to validate the correctness of the implementation and to evaluate both the current standard performance and the proposed enhancements. This work has been performed within the context of a project called FURIA, which is a strategic research project funded by the Spanish Ministry of Industry, Tourism and Commerce. A brief description of this project and its consortium has been also included herein, together with an introduction to the current situation of the DTTB in Spain (called TDT in Spanish)

Design of a simulation platform to test next generation of terrestrial DVB

Digital Terrestrial Television Broadcasting (DTTB) is a member of our daily life routine, and nonetheless, according to new users’ necessities in the fields of communications and leisure, new challenges are coming up. Moreover, the current Standard is not able to satisfy all the potential requirements. For that reason, first of all, a review of the current Standard has been performed within this work. Then, it has been identified the needing of developing a new version of the standard, ready to support enhanced services, as for example broadcasting transmissions to moving terminals or High Definition Television (HDTV) transmissions, among others. The main objective of this project is the design and development of a physical layer simulator of the whole DVB-T standard, including both the complete transmission and reception procedures. The simulator has been developed in Matlab. A detailed description of the simulator both from a functional and an architectural point of view is included. The simulator is the base for testing any possible modifications that may be included into the DVB-T2 future standard. In fact, several proposed enhancements have already been carried out and their performance has been evaluated. Specifically, the use of higher order modulation schemes, and the corresponding modifications in all the system blocks, have been included and evaluated. Furthermore, the simulator will allow testing other enhancements as the use of more efficient encoders and interleavers, MIMO technologies, and so on. A complete set of numerical results showing the performance of the different parts of the system, are presented in order to validate the correctness of the implementation and to evaluate both the current standard performance and the proposed enhancements. This work has been performed within the context of a project called FURIA, which is a strategic research project funded by the Spanish Ministry of Industry, Tourism and Commerce. A brief description of this project and its consortium has been also included herein, together with an introduction to the current situation of the DTTB in Spain (called TDT in Spanish)

Embedding and decoding hidden data channels on computer displays

In a given setup, a LCD screen is mounted horizontally so that objects, e.g. game tokens, can be placed on the surface of the display. A PC displays information on the screen, e.g. a floor plan of a board game. The object placed on the screen is equipped with one or more optical sensors that ¿look¿ at the display area under the object. The information captured by the sensor is transmitted back to the PC that displays the information (after optional pre-processing the object). In order to determine de position of the objects in the screen, the screen is partitioned into a large number of separate areas. A separate hidden data channel has to be implemented in each of these areas. The data transmitted through these data channels can be used to transmit position identifying the given area. The task of this work is to research and design a system for implementing such a multitude of hidden data channels on a video display with the following constraints: - The displayed hidden data channel shall be invisible or at least unobtrusive to the human eye in the chosen setup. - The capacity of the channel should be as large as possible. - The system should be able to function if the sensor is placed between two, or three of the hidden data channel areas. - The system needs to be robust against typical error signals like ¿strobing back light of the display¿. - The system should be able to adapt to special conditions found on different types of display families.Querol Giner, AJ. (2009). Embedding and decoding hidden data channels on computer displays. http://hdl.handle.net/10251/21015.Archivo delegad