Precision at Scale: System Design from Tiny Biosensors to Giant Arrays

In order to change the world, technological advancements must be made affordable and available for the general public to use. In other words, we must be able to scale our inventions effectively. Silicon integrated circuits are crucial components in scaling electronic systems because they are mass producible and offer a phenomenal cost-to-complexity ratio. This thesis summarizes the author’s work on highly scalable sensor and array systems. It presents three high precision systems, that demonstrate how the use of highly functional radio-frequency integrated circuits enables the realization of previously unfeasible architectures

Design and investigation of nanometric integrated circuits for all-digital frequency synthesisers

Disertacijoje nagrinėjami daugiajuosčių dažnio sintezatorių blokai, modeliai bei jų kūrimas taikant nanometrines integrinių grandynų technologijas. Iškeliama ir įrodoma hipotezė, kad taikant nanometrines technologijas visiškai skaitmeniniai dažnio sintezatoriai įgalina gauti parametrus, reikiamus daugiajuosčiams belai- džio ryšio siųstuvams-imtuvams. Darbo tikslas – sukurti visiškai skaitmeninio dažnio sintezatoriaus blokus, kuriuos naudojant galima pasiekti reikiamus sinte- zatoriaus, skirto daugiajuosčiams belaidžio ryšio siųstuvams-imtuvams, paramet- rus taikant nanometrines integrinių grandynų gamybos technologijas. Darbe išsp- ręsti tokie uždaviniai: ištirtos dažnio sintezatorių struktūros ir sukurta struktūra, tinkama įgyvendinti taikant nanometrines technologijas, sukurti ir ištirti siūlomos struktūros sintezatorių sudarančių blokų modeliai ir integriniai grandynai. Disertaciją sudaro įvadas, trys skyriai, bendrosios išvados, naudotos literatū- ros ir autoriaus publikacijų disertacijos tema sąrašai ir keturi priedai. Įvadiniame skyriuje aptariama tiriamoji problema, darbo aktualumas, aprašo- mas tyrimų objektas, formuluojamas darbo tikslas bei uždaviniai, aprašoma ty- rimų metodika, darbo mokslinis naujumas, darbo rezultatų praktinė reikšmė, gi- namieji teiginiai bei disertacijos struktūra. Pirmajame skyriuje apžvelgiamos dažnio sintezatorių rūšys, aprašomi pag- rindiniai dažnio sintezatorių parametrai ir dažniausiai naudojamos kokybės funk- cijos. Apžvelgiami dažnio sintezatorių modeliai ir jų veikimas fazės ir dažnio sri- tyse. Aprašomi visiškai skaitmeninio dažnio sintezatoriaus triukšmų šaltiniai. Skyriaus pabaigoje suformuluojami disertacijos uždaviniai. Antrajame skyriuje pasiūlyta ir taikoma nauja kokybės funkcija, leidžianti at- likti daugiajuosčių dažnio sintezatorių palyginamąją analizę. Iškeliami reikalavi- mai pagrindiniams sintezatoriaus blokams, nagrinėjami laikinio skaitmeninio kei- tiklio skiriamosios gebos didinimo būdai, sukurtas naujas laikinio skaitmeninio keitiklio modelis. Siūloma dažnio sintezatoriaus struktūra daugiajuosčiams siųs- tuvams-imtuvams. Trečiajame skyriuje pagal iškeltus reikalavimus daugiajuosčio dažnio sinte- zatoriaus blokams, taikant kompiuterinių skaičiavimų ir eksperimentinius meto- dus yra kuriami ir tiriami laikinio skaitmeninio keitiklio, skaitmeniniu būdu val- domo generatoriaus bei skaitmeninio filtro integriniai grandynai. Disertacijos tema yra atspausdinti 7 moksliniai straipsniai: 4 – mokslo žurna- luose, įtrauktuose į Clarivate Analytics Web of Science duomenų bazę, 1 – tarp- tautinių konferencijų medžiagoje, įtrauktoje į Clarivate Analytics Proceedings duomenų bazę, 2 – mokslo žurnaluose, referuojamuose kitose tarptautinėse duo- menų bazėse. Disertacijoje atliktų tyrimų rezultatai buvo paskelbti devyniose mokslinėse konferencijose Lietuvoje ir užsienyje

CMOS Integrated Power Amplifiers for RF Reconfigurable and Digital Transmitters

abstract: This dissertation focuses on three different efficiency enhancement methods that are applicable to handset applications. These proposed designs are based on three critical requirements for handset application: 1) Small form factor, 2) CMOS compatibility and 3) high power handling. The three presented methodologies are listed below: 1) A transformer-based power combiner architecture for out-phasing transmitters 2) A current steering DAC-based average power tracking circuit for on-chip power amplifiers (PA) 3) A CMOS-based driver stage for GaN-based switched-mode power amplifiers applicable to fully digital transmitters This thesis highlights the trends in wireless handsets, the motivates the need for fully-integrated CMOS power amplifier solutions and presents the three novel techniques for reconfigurable and digital CMOS-based PAs. Chapter 3, presents the transformer-based power combiner for out-phasing transmitters. The simulation results reveal that this technique is able to shrink the power combiner area, which is one of the largest parts of the transmitter, by about 50% and as a result, enhances the output power density by 3dB. The average power tracking technique (APT) integrated with an on-chip CMOS-based power amplifier is explained in Chapter 4. This system is able to achieve up to 32dBm saturated output power with a linear power gain of 20dB in a 45nm CMOS SOI process. The maximum efficiency improvement is about ∆η=15% compared to the same PA without APT. Measurement results show that the proposed method is able to amplify an enhanced-EDGE modulated input signal with a data rate of 70.83kb/sec and generate more than 27dBm of average output power with EVM<5%. Although small form factor, high battery lifetime, and high volume integration motivate the need for fully digital CMOS transmitters, the output power generated by this type of transmitter is not high enough to satisfy the communication standards. As a result, compound materials such as GaN or GaAs are usually being used in handset applications to increase the output power. Chapter 5 focuses on the analysis and design of two CMOS based driver architectures (cascode and house of cards) for driving a GaN power amplifier. The presented results show that the drivers are able to generate ∆Vout=5V, which is required by the compound transistor, and operate up to 2GHz. Since the CMOS driver is expected to drive an off-chip capacitive load, the interface components, such as bond wires, and decoupling and pad capacitors, play a critical role in the output transient response. Therefore, extensive analysis and simulation results have been done on the interface circuits to investigate their effects on RF transmitter performance. The presented results show that the maximum operating frequency when the driver is connected to a 4pF capacitive load is about 2GHz, which is perfectly matched with the reported values in prior literature.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

CMOS Data Converters for Closed-Loop mmWave Transmitters

With the increased amount of data consumed in mobile communication systems, new solutions for the infrastructure are needed. Massive multiple input multiple output (MIMO) is seen as a key enabler for providing this increased capacity. With the use of a large number of transmitters, the cost of each transmitter must be low. Closed-loop transmitters, featuring high-speed data converters is a promising option for achieving this reduced unit cost.In this thesis, both digital-to-analog (D/A) and analog-to-digital (A/D) converters suitable for wideband operation in millimeter wave (mmWave) massive MIMO transmitters are demonstrated. A 2 76 bit radio frequency digital-to-analog converter (RF-DAC)-based in-phase quadrature (IQ) modulator is demonstrated as a compact building block, that to a large extent realizes the transmit path in a closed-loop mmWave transmitter. The evaluation of an successive-approximation register (SAR) analog-to-digital converter (ADC) is also presented in this thesis. Methods for connecting simulated and measured performance has been studied in order to achieve a better understanding about the alternating comparator topology.These contributions show great potential for enabling closed-loop mmWave transmitters for massive MIMO transmitter realizations

Multiphase Digitally Controlled Oscillator for Future 5G Phased Arrays in 90 nm CMOS

This paper reports a low noise Digitally Controlled Oscillator (DCO) with multiphase outputs, suitable for next generation phased arrays. The DCO core is implemented using an 8 stage Rotary Traveling Wave Oscillator (RTWO) topology. Simple design equations are presented and insight is given in the layout implementation. Designed in a 90 nm CMOS process, the prototype is tunable from 31.4 to 37 GHz (i.e. 16% tuning range). Drawing 45 mW from a 1.2V supply, the simulated phase noise is -127.3 dBc/Hz at 10 MHz offset from a 34 GHz carrier, resulting in a phase-noise FoM of -181.4 dBc/Hz. Digitally tuned slow wave transmission lines are used to achieve a fine tuning resolution of 1.8 MHz, resulting in a state-of-the-art tuning FoMDT of -187 dBc/Hz.status: publishe

Bibliography of Lewis Research Center technical publications announced in 1993

This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1993. All the publications were announced in the 1993 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses

Technology 2000, volume 1

The purpose of the conference was to increase awareness of existing NASA developed technologies that are available for immediate use in the development of new products and processes, and to lay the groundwork for the effective utilization of emerging technologies. There were sessions on the following: Computer technology and software engineering; Human factors engineering and life sciences; Information and data management; Material sciences; Manufacturing and fabrication technology; Power, energy, and control systems; Robotics; Sensors and measurement technology; Artificial intelligence; Environmental technology; Optics and communications; and Superconductivity