Design of a tunable multi-band differential LC VCO using 0.35 mu m SiGe BiCMOS technology for multi-standard wireless communication systems

In this paper, an integrated 2.2-5.7GHz multi-band differential LC VCO for multi-standard wireless communication systems was designed utilizing 0.35 mu m SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post-layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3 V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78 GHz, 3.22-3.53 GHz, 3.48-3.91 GHz and 4.528-5.7 GHz) with a maximum bandwidth of 1.36 GHz and a minimum bandwidth of 300 MHz. The designed and simulated VCO can generate a differential output power between 0.992 and -6.087 dBm with an average power consumption of 44.21 mW including the buffers. The average second and third harmonics level were obtained as -37.21 and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment. Output power of the fundamental frequency changes between -6.087 and 0.992 dBm, depending on the bias conditions (operating bands). Based on the post-layout simulation results, the core VCO circuit draws a current between 2.4-6.3 mA and between 11.4 and 15.3 mA with the buffer circuit from 3.3 V supply. The circuit occupies an area of 1.477 mm(2) on Si substrate, including DC, digital and RF pads

A wideband linear tunable CDTA and its application in field programmable analogue array

This document is the Accepted Manuscript version of the following article: Hu, Z., Wang, C., Sun, J. et al. ‘A wideband linear tunable CDTA and its application in field programmable analogue array’, Analog Integrated Circuits and Signal Processing, Vol. 88 (3): 465-483, September 2016. Under embargo. Embargo end date: 6 June 2017. The final publication is available at Springer via https://link.springer.com/article/10.1007%2Fs10470-016-0772-7 © Springer Science+Business Media New York 2016In this paper, a NMOS-based wideband low power and linear tunable transconductance current differencing transconductance amplifier (CDTA) is presented. Based on the NMOS CDTA, a novel simple and easily reconfigurable configurable analogue block (CAB) is designed. Moreover, using the novel CAB, a simple and versatile butterfly-shaped FPAA structure is introduced. The FPAA consists of six identical CABs, and it could realize six order current-mode low pass filter, second order current-mode universal filter, current-mode quadrature oscillator, current-mode multi-phase oscillator and current-mode multiplier for analog signal processing. The Cadence IC Design Tools 5.1.41 post-layout simulation and measurement results are included to confirm the theory.Peer reviewedFinal Accepted Versio

Millimeter wave experiment for ATS-F

A detailed description of spaceborne equipment is provided. The equipment consists of two transmitters radiating signals at 20 and 30 GHz from either U.S. coverage horn antennas or a narrow beam parabolic antenna. Three modes of operation are provided: a continuous wave mode, a multitone mode in which nine spectral lines having 180 MHz separation and spaced symmetrically about each carrier, and a communications mode in which communications signals from the main spacecraft transponder are modulated on the two carriers. Detailed performance attained in the flight/prototype model of the equipment is presented both under laboratory conditions and under environmental extremes. Provisions made for ensuring reliability in space operation are described. Also described the bench test equipment developed for use with the experiment, and a summary of the new technology is included

Communication Subsystems for Emerging Wireless Technologies

The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels

Design of reconfigurable multi-mode RF circuits

Wireless communication systems and devices have been developing at a much faster pace in the past few years. With the introduction of new applications and services and the increasing demand for higher data rate comes the need for new frequency bands and new standards. One critical issue for next generation wireless devices is how to support all of the existing and emerging bands while not increasing the cost and power consumption. A feasible solution is the concept of the software-defined radio where a single receiver can be reconfigured to operate in different modes, each of which supports one or several bands and/or standards. To implement such a reconfigurable receiver, reconfigurable RF building blocks, such as the LNA, mixer, VCO, etc., are required. This dissertation focuses on two key blocks: the low noise amplifier (LNA) and the voltage controlled oscillator (VCO). First the design, modeling and characterization of a multi-tap transformer are discussed. Simple mathematical calculations are utilized to estimate the inductances and coupling coefficients from the physical parameters of a multi-tap transformer. The design method is verified with several designed multi-tap transformers that are characterized up to 10 GHz using Momentum simulation results. The effect of switch loss on a switched multi-tap transformer is explored and a broadband lumped-element model of the multi-tap transformer is also proposed. Next a reconfigurable multimode LNA capable of single-band, concurrent dual-band, and ultra-wideband operation is presented. The multimode operation is realized by incorporating a switched multi-tap transformer into the input matching network of an inductively degenerated common source amplifier. The proposed LNA achieves single band matching at 2.8, 3.3, and 4.6 GHz; concurrent dual-band matching at 2.05 and 5.65 GHz; and ultra-wideband matching from 4.3 to 10.8 GHz. The chip was fabricated in a 0.13 m CMOS process, and occupies an area of 0.72 mm2, and has a power dissipation of 6.4 mW from a 1.2-V supply. Finally, a triple-mode VCO using a transformer-based 4th order tank with tunable transconductance cells coupling the primary and secondary inductor is introduced. The tank impedance can be re-shaped by the transconductance cells through the tuning of their biasing currents. With the control of biasing current, VCO is configured in three modes, capable of generating a single frequency in 3- and 5- GHz bands, respectively, and two frequencies in both 3- and 5- GHz bands simultaneously. The triple-mode VCO was fabricated in a 0.13 μm CMOS process, occupies an area of 0.16 mm2, and dissipates 5.6 mW from a 1.2-V supply

Integrated Transversal Equalizers in High-Speed Fiber-Optic Systems

Intersymbol interference (ISI) caused by intermodal dispersion in multimode fibers is the major limiting factor in the achievable data rate or transmission distance in high-speed multimode fiber-optic links for local area networks applications. Compared with optical-domain and other electrical-domain dispersion compensation methods, equalization with transversal filters based on distributed circuit techniques presents a cost-effective and low-power solution. The design of integrated distributed transversal equalizers is described in detail with focus on delay lines and gain stages. This seven-tap distributed transversal equalizer prototype has been implemented in a commercial 0.18-µm SiGe BiCMOS process for 10-Gb/s multimode fiber-optic links. A seven-tap distributed transversal equalizer reduces the ISI of a 10-Gb/s signal after 800 m of 50-µm multimode fiber from 5 to 1.38 dB, and improves the bit-error rate from about 10^-5 to less than 10^-12

A Wideband 77-GHz, 17.5-dBm Fully Integrated Power Amplifier in Silicon

A 77-GHz, +17.5 dBm power amplifier (PA) with fully integrated 50-Ω input and output matching and fabricated in a 0.12-µm SiGe BiCMOS process is presented. The PA achieves a peak power gain of 17 dB and a maximum single-ended output power of 17.5 dBm with 12.8% of power-added efficiency (PAE). It has a 3-dB bandwidth of 15 GHz and draws 165 mA from a 1.8-V supply. Conductor-backed coplanar waveguide (CBCPW) is used as the transmission line structure resulting in large isolation between adjacent lines, enabling integration of the PA in an area of 0.6 mm^2. By using a separate image-rejection filter incorporated before the PA, the rejection at IF frequency of 25 GHz is improved by 35 dB, helping to keep the PA design wideband