First experiments on MagPieR: a planar wireless magnetic and piezoelectric microrobot.

International audienceThe paper documents the principle and experiments of the "2mm dash" winner at NIST IEEE Mobile Microrobotics Challenge held at ICRA2010 in Alaska [1]. Submission is made for the special session "ICRA Robot Challenge: Advancing Research Through Competitions". The new MagPieR microrobot was specially designed for breaking the speed record, providing a planar magnetic actuation with an optimised coils setup and a subsequent piezoelectric actuation for improved sliding condition. The paper describes the principle of actuation, the microrobot manufacturing flowchart and the assembly setup. Some simulations are provided with a first series of experimental data and conclusions

Pjezorobotų trajektorijų valdymas nanopalydovų stabilizavimui

Rapid industrial advancement requires novel ideas, new scientific approaches and effective technologies that would ensure quality and precision. Application of piezoelectric actuators in robotics opens many possibilities to create systems with extreme precision and control. A very important step in the development of autonomous robots is the formation of motion trajectories. Classical interpolation methods used for formation of the trajectories are suitable only when robots have wheels, legs or other parts for motion transmission. Piezorobots that are analyzed in this dissertation have no additional components that create motion, only contact points with the static plane. Therefore, traditional motion formation methods are not suitable and a problem arises how to define motion trajectory of such device. The aim of this work is to create a trajectory control algorithm of multi-degrees-of-freedom piezorobot used for nanosatellite stabilization. In order to achieve the objective, the following tasks had to be solved: to analyze constructions of precise piezorobots, their operating principles and motion formation methods; to analyze stabilization problems of satellites and application of multi-degrees-of-freedom piezorobots for nanosatellite stabilization; to create piezorobots’ motion formation algorithms according to electrode excitation schemes, to perform an experimental research; to determine quantitative characteristics of the constructed piezorobots and their motion trajectories. The introduction describes the importance and novelty of this thesis, goals of this work, its practical value and defended statements. The first chapter analyses the principals of ultrasonic devices, gives a thorough review of constructions of ultrasonic devices with multi-degrees-of-freedom. The second chapter provides a review of satellite stabilization principles and how multi-degrees-of-freedom piezorobots can be applied for nanosatellite stabilization. Motion formation methods for ultrasonic devices with multi-degrees-of-freedom are presented. The third chapter presents the detailed analysis of different piezorobots. In the fourth chapter experimental results are provided. Trajectory planning of piezorobot is shown, results are compared to numerical calculations performed in the third chapter. The conclusions about applicability of piezorobots’ motion formation algorithms according to electrode excitation schemes are given. Seven articles focusing on the subject of the dissertation have been published, two presentations on the subject have been presented in conferences at international level. The research for the dissertation has been funded by the Lithuanian State Science and Studies Foundation: European Regional Development Fund, Project No. DOTSUT-234 and Research Council of Lithuania, Project No. MIP-084/2015.Dissertatio

Ultrasonic sensor platforms for non-destructive evaluation

Robotic vehicles are receiving increasing attention for use in Non-Destructive Evaluation (NDE), due to their attractiveness in terms of cost, safety and their accessibility to areas where manual inspection is not practical. A reconfigurable Lamb wave scanner, using autonomous robotic platforms is presented. The scanner is built from a fleet of wireless miniature robotic vehicles, each with a non-contact ultrasonic payload capable of generating the A0 Lamb wave mode in plate specimens. An embedded Kalman filter gives the robots a positional accuracy of 10mm. A computer simulator, to facilitate the design and assessment of the reconfigurable scanner, is also presented. Transducer behaviour has been simulated using a Linear Systems approximation (LS), with wave propagation in the structure modelled using the Local Interaction Simulation Approach (LISA). Integration of the LS and LISA approaches were validated for use in Lamb wave scanning by comparison with both analytical techniques and more computationally intensive commercial finite element/diference codes. Starting with fundamental dispersion data, the work goes on to describe the simulation of wave propagation and the subsequent interaction with artificial defects and plate boundaries. The computer simulator was used to evaluate several imaging techniques, including local inspection of the area under the robot and an extended method that emits an ultrasonic wave and listens for echos (B-Scan). These algorithms were implemented in the robotic platform and experimental results are presented. The Synthetic Aperture Focusing Technique (SAFT) was evaluated as a means of improving the fidelity of B-Scan data. It was found that a SAFT is only effective for transducers with reasonably wide beam divergence, necessitating small transducers with a width of approximately 5mm. Finally, an algorithm for robot localisation relative to plate sections was proposed and experimentally validated

Tactile sensors for robot handling

First and second generation robots have been used cost effectively in high‐volume ‘fixed’ or ‘hard’ automated manufacturing/assembly systems. They are ‘limited‐ability’ devices using simple logic elements or primitive sensory feedback. However, in the unstructured environment of most manufacturing plants it is often necessary to locate, identify, orientate and position randomly presented components. Visual systems have been researched and developed to provide a coarse resolution outline of objects. More detailed and precise definition of parts is usually obtained by high resolution tactile sensing arrays. This paper reviews and discusses the current state of the art in tactile sensing

Preliminary finite element modeling of a piezoelectric actuated marine propulsion fin

New technologies surrounding composite materials and autonomous underwater vehicle (AUV) design have led to numerous studies involving the marine propulsion for these AUVs. AUVs traditionally are classified as highly efficient, payload capable, and can be utilized as reconnaissance or surveillance vehicles. Undullatory and oscillatory propulsion devices have been conceived to replace the present propulsion technologies, of propellers, with highly maneuverable, efficient, and quiet propulsion systems. Undullatory and oscillatory propulsion has been around for centuries employed by aquatic life, but only recently have the mini-technologies been available to present such propulsion devices economically and with enough materials research as to mimic biologic life on the same scale. Piezoelectric properties coupled with a thin plate allow for actuation properties, similar to bimetallic metals. Applying two piezoelectrics to the fixed end of a cantilevered beam or plate, on opposite sides, and actuating them with an opposite phase shift in electrical voltage potential results in transverse motion of the beam from the orthogonal plane to the vertical axis of the piezoelectric device. Coupling this property to a particular fiber orientation, composite thin plate, significantly increases the actuation properties. In addition, placing more than two piezoelectrics along the length of the thin composite plate gives the potential to increase actuation properties and change the motion from oscillatory to undullatory. These motions can again be increased by utilizing the natural vibration modes of the thin composite plate with piezoelectrics near resonance actuation. The current research is involved with modeling a piezoelectric actuated marine propulsion fin using the Galerkin finite element technique. An experimental proof of concept was developed to compare results. Using fluid-structure interaction (FSI) methods, it is proposed that the fluid and structure programs are resolved within one program. This is in contrast to traditional attempts at FSI problems that utilize a computational fluid dynamics (CFD) solver transferring load data between a structural dynamics/finite element (FE) program

Scalability study for robotic hand platform

The goal of this thesis project was to determine the lower limit of scale for the RIT robotic grasping hand. This was accomplished using a combination of computer simulation and experimental studies. A force analysis was conducted to determine the size of air muscles required to achieve appropriate contact forces at a smaller scale. Input variables, such as the actuation force and tendon return force, were determined experimentally. A dynamic computer model of the hand system was then created using Recurdyn. This was used to predict the contact (grasping) force of the fingers at full-scale, half-scale, and quarter-scale. Correlation between the computer model and physical testing was achieved for both a life-size and half-scale finger assembly. To further demonstrate the scalability of the hand design, both half and quarter-scale robotic hand rapid prototype assemblies were built using 3D printing techniques. This thesis work identified the point where further miniaturization would require a change in the manufacturing process to micro-fabrication. Several techniques were compared as potential methods for making a production intent quarter-scale robotic hand. Investment casting, Swiss machining, and Selective Laser Sintering were the manufacturing techniques considered. A quarter-scale robotic hand tested the limits of each technology. Below this scale, micro-machining would be required. The break point for the current actuation method, air muscles, was also explored. Below the quarter-scale, an alternative actuation method would also be required. Electroactive Polymers were discussed as an option for the micro-scale. In summary, a dynamic model of the RIT robotic grasping hand was created and validated as scalable at full and half-scales. The model was then used to predict finger contact forces at the quarter-scale. The quarter-scale was identified as the break point in terms of the current RIT robotic grasping hand based on both manufacturing and actuation. A novel, prototype quarter-scale robotic hand assembly was successfully built by an additive manufacturing process, a high resolution 3D printer. However, further miniaturization would require alternate manufacturing techniques and actuation mechanisms

MEMS Technology for Biomedical Imaging Applications

Biomedical imaging is the key technique and process to create informative images of the human body or other organic structures for clinical purposes or medical science. Micro-electro-mechanical systems (MEMS) technology has demonstrated enormous potential in biomedical imaging applications due to its outstanding advantages of, for instance, miniaturization, high speed, higher resolution, and convenience of batch fabrication. There are many advancements and breakthroughs developing in the academic community, and there are a few challenges raised accordingly upon the designs, structures, fabrication, integration, and applications of MEMS for all kinds of biomedical imaging. This Special Issue aims to collate and showcase research papers, short commutations, perspectives, and insightful review articles from esteemed colleagues that demonstrate: (1) original works on the topic of MEMS components or devices based on various kinds of mechanisms for biomedical imaging; and (2) new developments and potentials of applying MEMS technology of any kind in biomedical imaging. The objective of this special session is to provide insightful information regarding the technological advancements for the researchers in the community

Power-Scavenging MEMS Robots

This thesis includes the design, modeling, and testing of novel, power-scavenging, biologically inspired MEMS microrobots. Over one hundred 500-μm and 990-μm microrobots with two, four, and eight wings were designed, fabricated, characterized. These microrobots constitute the smallest documented attempt at powered flight. Each microrobot wing is comprised of downward-deflecting, laser-powered thermal actuators made of gold and polysilicon; the microrobots were fabricated in PolyMUMPs® (Polysilicon Multi-User MEMS Processes). Characterization results of the microrobots illustrate how wing-tip deflection can be maximized by optimizing the gold-topolysilicon ratio as well as the dimensions of the actuator-wings. From these results, an optimum actuator-wing configuration was identified. It also was determined that the actuator-wing configuration with maximum deflection and surface area yet minimum mass had the greatest lift-to-weight ratio. Powered testing results showed that the microrobots successfully scavenged power from a remote 660-nm laser. These microrobots also demonstrated rapid downward flapping, but none achieved flight. The results show that the microrobots were too heavy and lacked sufficient wing surface area. It was determined that a successfully flying microrobot can be achieved by adding a robust, light-weight material to the optimum actuator-wing configuration—similar to insect wings. The ultimate objective of the flying microrobot project is an autonomous, fully maneuverable flying microrobot that is capable of sensing and acting upon a target. Such a microrobot would be capable of precise lethality, accurate battle-damage assessment, and successful penetration of otherwise inaccessible targets

Stepper microactuators driven by ultrasonic power transfer

Advances in miniature devices for biomedical applications are creating ever-increasing requirements for their continuous, long lasting, and reliable energy supply, particularly for implanted devices. As an alternative to bulky and cost inefficient batteries that require occasional recharging and replacement, energy harvesting and wireless power delivery are receiving increased attention. While the former is generally only suited for low-power diagnostic microdevices, the latter has greater potential to extend the functionality to include more energy demanding therapeutic actuation such as drug release, implant mechanical adjustment or microsurgery. This thesis presents a novel approach to delivering wireless power to remote medical microdevices with the aim of satisfying higher energy budgets required for therapeutic functions. The method is based on ultrasonic power delivery, the novelty being that actuation is powered by ultrasound directly rather than via piezoelectric conversion. The thesis describes a coupled mechanical system remotely excited by ultrasound and providing conversion of acoustic energy into motion of a MEMS mechanism using a receiving membrane coupled to a discrete oscillator. This motion is then converted into useful stepwise actuation through oblique mechanical impact. The problem of acoustic and mechanical impedance mismatch is addressed. Several analytical and numerical models of ultrasonic power delivery into the human body are developed. Major design challenges that have to be solved in order to obtain acceptable performance under specified operating conditions and with minimum wave reflections are discussed. A novel microfabrication process is described, and the resulting proof-of-concept devices are successfully characterized.Open Acces

The design and characterisation of miniature robotics for astronomical instruments

Micro robotics has the potential to improve the efficiency and reduce cost of future multi-object instruments for astronomy. This thesis reports on the development and evolution of a micro autonomous pick-off mirror called the Micro Autonomous Positioning System (MAPS) that can be used in a multi-object spectrograph. The design of these micro-autonomous pick-off mirrors is novel as they are capable of high precision positioning using electromagnetic propulsion through utilising non-conventional components and techniques. These devices are self-driven robotic units, which with the help of an external control system are capable of positioning themselves on an instruments focal plane to within 24 μm. This is different from other high precision micro robotics as they normally use piezoelectric actuators for propulsion. Micro robots have been developed that use electromagnetic motors, however they are not used for high precision applications. Although there is a plethora of literature covering design, functionality and capability of precision micro autonomous systems, there is limited research on characterisation methods for their use in astronomical applications. This work contributes not only to the science supporting the design of a micro-autonomous pick-off mirror but also presents a framework for characterising such miniature mechanisms. The majority of instruments are presented with a curved focal plane. Therefore, to ensure that the pick-off mirrors are aligned properly with the receiving optics, either the pick-off mirror needs to be tipped or the receiving optics repositioned. Currently this function is implemented in the beam steering mirror (i.e. the receiving optics). The travel range required by the beam steering mirror is relatively large, and as such, it is more difficult to achieve the positional accuracy and stability. By incorporating this functionality in the pick-off mirror, the instrument can be optimised in terms of size, accuracy and stability. A unique self-adjusting mirror (SAM) is thus proposed as a solution and detailed. As a proof-of-concepts both MAPS and SAM usability in multi-object spectrographs was evaluated and validated. The results indicate their potential to meet the requirements of astronomical instruments and reduce both the size and cost