Plasticization and antiplasticization of polymer melts diluted by low molar mass species

An analysis of glass formation for polymer melts that are diluted by structured molecular additives is derived by using the generalized entropy theory, which involves a combination of the Adam-Gibbs model and the direct computation of the configurational entropy based on a lattice model of polymer melts that includes monomer structural effects. Antiplasticization is accompanied by a "toughening" of the glass mixture relative to the pure polymer, and this effect is found to occur when the diluents are small species with strongly attractive interactions with the polymer matrix. Plasticization leads to a decreased glass transition temperature T_g and a "softening" of the fragile host polymer in the glass state. Plasticization is prompted by small additives with weakly attractive interactions with the polymer matrix. The shifts in T_g of polystyrene diluted by fully flexible short oligomers are evaluated from the computations, along with the relative changes in the isothermal compressibility at T_g to characterize the extent to which the additives act as antiplasticizers or plasticizers. The theory predicts that a decreased fragility can accompany both antiplasticization and plasticization of the glass by molecular additives. The general reduction in the T_g and fragility of polymers by these molecular additives is rationalized by analyzing the influence of the diluent's properties (cohesive energy, chain length, and stiffness) on glass formation in diluted polymer melts. The description of glass formation at fixed temperature that is induced upon change the fluid composition directly implies the Angell equation for the structural relaxation time as function of the polymer concentration, and the computed "zero mobility concentration" scales linearly with the inverse polymerization index N.Comment: 12 pages, 15 figure

BIOAVAILABILITY OF ELEMENTS FOR EFFECTIVE PHYTOREMEDIATION AND PHYTOMINING: THE ROLE OF RHIZOSPHERE PROCESSES

The success of phytoremediation (especially phytoextraction) and phytomining depends heavily on the bioavailability of target elements, which, among others, is a function of soil mineral phases, soil organic matter, pH and redox potential. The use of soil additives which, e.g., change soil pH or increase the amount of chelating compounds, has been propagated in the past in order to desorb the target elements from the soil matrix. These additives, however, may have negative environmental consequences by causing leaching of toxic elements from the soil due to enhanced mobility in the soil solution. For this reason less dangerous alternatives are necessary which use the natural capacity of plants to increase availability of target elements in their root environment

Development of a novel metastable composite material

The development of a new family of mouldable metastable composite materials has been demonstrated. Their special quality is derived from the ability to maintain the matrix as a supercooled liquid or gel whose solidification can be triggered mechanically, as desired, by a user. This article describes some aspects of the development work. In particular, the following are explained: the choice of matrix material; the use of additives to enhance the properties of the matrix; and the selection of reinforcement fibre. As part of the work, some mechanical testing was performed on several variations of a matrix-fibre pair and, to demonstrate the potential of such materials, some comparisons were made with a possible competitor material, a glass-reinforced urethane. It was shown that the metastable material could be formulated to provide mechanical properties that would make it suitable for applications such as orthopaedic casting, splinting and body armour, and in items of sports equipment, these being areas where its mouldability could be particularly desirable

Internally coated air-cooled gas turbine blading

Ten candidate modified nickel-aluminide coatings were developed using the slip pack process. These coatings contain additives such as silicon, chromium and columbium in a nickel-aluminum coating matrix with directionally solidified MAR-M200 + Hf as the substrate alloy. Following a series of screening tests which included strain tolerance, dynamic oxidation and hot corrosion testing, the Ni-19A1-1Cb (nominal composition) coating was selected for application to the internal passages of four first-stage turbine blades. Process development results indicate that a dry pack process is suitable for internal coating application resulting in 18 percent or less reduction in air flow. Coating uniformity, based on coated air-cooled blades, was within + or - 20 percent. Test results show that the presence of additives (silicon, chromium or columbium) appeared to improve significantly the ductility of the NiA1 matrix. However, the environmental resistance of these modified nickel-aluminides were generally inferior to the simple aluminides

Sugar additives for MALDI matrices improve signal allowing the smallest nucleotide change (A:T) in a DNA sequence to be resolved

Sample preparation for matrix-assisted laser desorption/ionization (MALDI) mass spectrometry (MS) of DNA is critical for obtaining high quality mass spectra. Sample impurity, solvent content, substrate surface and environmental conditions (temperature and humidity) all affect the rate of matrix–analyte co-crystallization. As a result, laser fluence threshold for desorption/ionization varies from spot to spot. When using 3-hydroxypicolinic acid (3-HPA) as the matrix, laser fluence higher than the threshold value reduces mass resolution in time-of-flight (TOF) MS as the excess energy transferred to DNA causes metastable decay. This can be overcome by either searching for ‘hot’ spots or adjusting the laser fluence. However, both solutions may require a significant amount of operator manipulation and are not ideal for automatic measurements. We have added various sugars for crystallization with the matrix to minimize the transfer of excess laser energy to DNA molecules. Fructose and fucose were found to be the most effective matrix additives. Using these additives, mass resolution for DNA molecules does not show noticeable deterioration as laser energy increases. Improved sample preparation is important for the detection of single nucleotide polymorphisms (SNPs) using primer extension with a single nucleotide. During automatic data acquisition it is difficult to routinely detect heterozygous A/T mutations, which requires resolving a mass difference of 9 Da, unless a sugar is added during crystallization

Method for producing fiber reinforced metallic composites Patent

Description of method for producing metallic composites reinforced with ceramic and refractory hard metals that are fibered in plac

Flame Retardant Intumescent Polyamide 11 Nanocomposites – Further Study

The objective of this research is to develop improved polyamide 11 and 12 polymers with enhanced flame retardancy, thermal, and mechanical properties for selective laser sintering (SLS) rapid manufacturing (RM). In the present study, a nanophase was introduced into the polyamide 11 and combine with a conventional intumescent flame retardant (FR) additive via twin screw extrusion. Arkema Rilsan® polyamide 11 molding polymer pellets were used with two types of nanoparticles such as: chemically modified montmorillonite (MMT) organoclays and carbon nanofibers (CNFs). Two types of Clariant’s Exolit® OP 1311 and 1312 intumescent FR additives were used to generate a family of FR intumescent polyamide 11 nanocomposites with anticipated synergism.Mechanical Engineerin

Tailoring the flow of soft glasses by soft additives

We examine the vitrification and melting of asymmetric star polymers mixtures by combining rheological measurements with mode coupling theory. We identify two types of glassy states, a {\it single} glass, in which the small component is fluid in the glassy matrix of the big one and a {\it double} glass, in which both components are vitrified. Addition of small star polymers leads to melting of {\it both} glasses and the melting curve has a non-monotonic dependence on the star-star size ratio. The phenomenon opens new ways for externally steering the rheological behavior of soft matter systems.Comment: 4 pages, 4 figures, accepted in Phys. Rev. Let

Bio-Based Renewable Additives for Anti-Icing Applications (Phase II)

The performance and impacts of several agro-based anti-icers along with a traditional chloride-based anti-icer (salt brine) were evaluated. A statistical design of experiments (central composite design) was employed for developing anti-icing liquids consisting of cost-competitive chemicals such as agro-based compounds (e.g., Concord grape extract and glycerin), sodium chloride, sodium metasilicate, and sodium formate. The following experimentally obtained parameters were examined as a function of the formulation design: ice-melting capacity at 25°F (−3.9°C), splitting strength of Portland cement mortar samples after 10 freeze-thaw/deicer cycles, corrosion rate of C1010 carbon steel after 24-hour immersion, and impact on asphalt binder stiffness and m-value. One viable formula (“best performer”) was tested for thermal properties by measuring its differential scanning calorimetry (DSC) thermograms, the friction coefficient of asphalt pavement treated by this anti-icing formulation (vs. 23 wt.% NaCl and beet juice blend) at 25°F after being applied at 30 gallons per lane mile (1 hour after simulated trafficking and plowing), and other properties (pH, oxygen demand in COD). Laboratory data shed light on the selection and formulation of innovative agro-based snow- and ice-control chemicals that can significantly reduce the costs of winter maintenance operations