173 research outputs found

    Indoor Channel Measurement for Wireless Communication

    Get PDF

    Robust frequency-domain turbo equalization for multiple-input multiple-output (MIMO) wireless communications

    Get PDF
    This dissertation investigates single carrier frequency-domain equalization (SC-FDE) with multiple-input multiple-output (MIMO) channels for radio frequency (RF) and underwater acoustic (UWA) wireless communications. It consists of five papers, selected from a total of 13 publications. Each paper focuses on a specific technical challenge of the SC-FDE MIMO system. The first paper proposes an improved frequency-domain channel estimation method based on interpolation to track fast time-varying fading channels using a small amount of training symbols in a large data block. The second paper addresses the carrier frequency offset (CFO) problem using a new group-wise phase estimation and compensation algorithm to combat phase distortion caused by CFOs, rather than to explicitly estimate the CFOs. The third paper incorporates layered frequency-domain equalization with the phase correction algorithm to combat the fast phase rotation in coherent communications. In the fourth paper, the frequency-domain equalization combined with the turbo principle and soft successive interference cancelation (SSIC) is proposed to further improve the bit error rate (BER) performance of UWA communications. In the fifth paper, a bandwidth-efficient SC-FDE scheme incorporating decision-directed channel estimation is proposed for UWA MIMO communication systems. The proposed algorithms are tested by extensive computer simulations and real ocean experiment data. The results demonstrate significant performance improvements in four aspects: improved channel tracking, reduced BER, reduced computational complexity, and enhanced data efficiency --Abstract, page iv

    Iterative Receiver for MIMO-OFDM System with ICI Cancellation and Channel Estimation

    Get PDF
    As a multi-carrier modulation scheme, Orthogonal Frequency Division Multiplexing (OFDM) technique can achieve high data rate in frequency-selective fading channels by splitting a broadband signal into a number of narrowband signals over a number of subcarriers, where each subcarrier is more robust to multipath. The wireless communication system with multiple antennas at both the transmitter and receiver, known as multiple-input multiple-output (MIMO) system, achieves high capacity by transmitting independent information over different antennas simultaneously. The combination of OFDM with multiple antennas has been considered as one of most promising techniques for future wireless communication systems. The challenge in the detection of a space-time signal is to design a low-complexity detector, which can efficiently remove interference resulted from channel variations and approach the interference-free bound. The application of iterative parallel interference canceller (PIC) with joint detection and decoding has been a promising approach. However, the decision statistics of a linear PIC is biased toward the decision boundary after the first cancellation stage. In this thesis, we employ an iterative receiver with a decoder metric, which considerably reduces the bias effect in the second iteration, which is critical for the performance of the iterative algorithm. Channel state information is required in a MIMO-OFDM system signal detection at the receiver. Its accuracy directly affects the overall performance of MIMO-OFDM systems. In order to estimate the channel in high-delay-spread environments, pilot symbols should be inserted among subcarriers before transmission. To estimate the channel over all the subcarriers, various types of interpolators can be used. In this thesis, a linear interpolator and a trigonometric interpolator are compared. Then we propose a new interpolator called the multi-tap method, which has a much better system performance. In MIMO-OFDM systems, the time-varying fading channels can destroy the orthogonality of subcarriers. This causes serious intercarrier interference (ICI), thus leading to significant system performance degradation, which becomes more severe as the normalized Doppler frequency increases. In this thesis, we propose a low-complexity iterative receiver with joint frequency- domain ICI cancellation and pilot-assisted channel estimation to minimize the effect of time-varying fading channels. At the first stage of receiver, the interference between adjacent subcarriers is subtracted from received OFDM symbols. The parallel interference cancellation detection with decision statistics combining (DSC) is then performed to suppress the interference from other antennas. By restricting the interference to a limited number of neighboring subcarriers, the computational complexity of the proposed receiver can be significantly reduced. In order to construct the time variant channel matrix in the frequency domain, channel estimation is required. However, an accurate estimation requiring complete knowledge of channel time variations for each block, cannot be obtained. For time- varying frequency-selective fading channels, the placement of pilot tones also has a significant impact on the quality of the channel estimates. Under the assumption that channel variations can be approximated by a linear model, we can derive channel state information (CSI) in the frequency domain and estimate time-domain channel parameters. In this thesis, an iterative low-complexity channel estimation method is proposed to improve the system performance. Pilot symbols are inserted in the transmitted OFDM symbols to mitigate the effect of ICI and the channel estimates are used to update the results of both the frequency domain equalizer and the PICDSC detector in each iteration. The complexity of this algorithm can be reduced because the matrices are precalculated and stored in the receiver when the placement of pilots symbols is fixed in OFDM symbols before transmission. Finally, simulation results show that the proposed MIMO-OFDM iterative receiver can effectively mitigate the effect of ICI and approach the ICI-free performance over time-varying frequency-selective fading channels

    Multiple-Resampling Receiver Design for OFDM Over Doppler-Distorted Underwater Acoustic Channels

    Get PDF
    Cataloged from PDF version of article.In this paper, we focus on orthogonal frequency-divisionmultiplexing (OFDM) receiver designs for underwater acoustic (UWA) channels with user- and/or path-specific Doppler scaling distortions. The scenario is motivated by the cooperative communications framework, where distributed transmitter/receiver pairs may experience significantly different Doppler distortions, as well as by the single-user scenarios, where distinct Doppler scaling factors may exist among different propagation paths. The conventional approach of front–end resampling that corrects for common Doppler scalingmay not be appropriatein such scenarios, rendering a post-fast-Fourier-transform (FFT) signal that is contaminated by user- and/or path-specific intercarrier interference. To counteract this problem, we propose a family of front–end receiver structures thatutilizemultiple-resampling (MR)branches,eachmatched to the Doppler scaling factor of a particular user and/or path. Following resampling, FFT modules transform the Doppler-compensated signals into the frequency domain for further processing through linear or nonlinear detection schemes. As part of the overall receiver structure, a gradient–descent approachis also proposed to refine the channel estimates obtained by standard sparse channel estimators. The effectiveness and robustness of the proposed receivers are demonstrated via simulations, as well as emulations based on real data collected during the 2010 Mobile Acoustic Communications Experiment (MACE10, Martha’s Vineyard, MA) and the 2008 Kauai Acomms MURI (KAM08, Kauai, HI) experiment

    Channel Estimation Architectures for Mobile Reception in Emerging DVB Standards

    Get PDF
    Throughout this work, channel estimation techniques have been analyzed and proposed for moderate and very high mobility DVB (digital video broadcasting) receivers, focusing on the DVB-T2 (Digital Video Broadcasting - Terrestrial 2) framework and the forthcoming DVB-NGH (Digital Video Broadcasting - Next Generation Handheld) standard. Mobility support is one of the key features of these DVB specifications, which try to deal with the challenge of enabling HDTV (high definition television) delivery at high vehicular speed. In high-mobility scenarios, the channel response varies within an OFDM (orthogonal frequency-division multiplexing) block and the subcarriers are no longer orthogonal, which leads to the so-called ICI (inter-carrier interference), making the system performance drop severely. Therefore, in order to successfully decode the transmitted data, ICI-aware detectors are necessary and accurate CSI (channel state information), including the ICI terms, is required at the receiver. With the aim of reducing the number of parameters required for such channel estimation while ensuring accurate CSI, BEM (basis expansion model) techniques have been analyzed and proposed for the high-mobility DVB-T2 scenario. A suitable clustered pilot structure has been proposed and its performance has been compared to the pilot patterns proposed in the standard. Different reception schemes that effectively cancel ICI in combination with BEM channel estimation have been proposed, including a Turbo scheme that includes a BP (belief propagation) based ICI canceler, a soft-input decision-directed BEM channel estimator and the LDPC (low-density parity check) decoder. Numerical results have been presented for the most common channel models, showing that the proposed receiver schemes allow good reception, even in receivers with extremely high mobility (up to 0.5 of normalized Doppler frequency).Doktoretza tesi honetan, hainbat kanal estimazio teknika ezberdin aztertu eta proposatu dira mugikortasun ertain eta handiko DVB (Digital Video Broadcasting) hartzaileentzat, bigarren belaunaldiko Lurreko Telebista Digitalean DVB-T2 (Digital Video Broadcasting - Terrestrial 2 ) eta hurrengo DVB-NGH (Digital Video Broadcasting - Next Generation Handheld) estandarretan oinarrututa. Mugikortasuna bigarren belaunaldiko telebista estandarrean funtsezko ezaugarri bat da, HDTV (high definition television) zerbitzuak abiadura handiko hartzaileetan ahalbidetzeko erronkari aurre egiteko nahian. Baldintza horietan, kanala OFDM (ortogonalak maiztasun-zatiketa multiplexing ) sinbolo baten barruan aldatzen da, eta subportadorak jada ez dira ortogonalak, ICI-a (inter-carrier interference) sortuz, eta sistemaren errendimendua hondatuz. Beraz, transmititutako datuak behar bezala deskodeatzeko, ICI-a ekiditeko gai diren detektagailuak eta CSI-a (channel state information) zehatza, ICI osagaiak barne, ezinbestekoak egiten dira hartzailean. Kanalaren estimazio horretarako beharrezkoak diren parametro kopurua murrizteko eta aldi berean CSI zehatza bermatzeko, BEM (basis expansion model) teknika aztertu eta proposatu da ICI kanala identifikatzeko mugikortasun handiko DVB-T2 eszenatokitan. Horrez gain, pilotu egitura egokia proposatu da, estandarrean proposatutako pilotu ereduekin alderatuz BEM estimazioan oinarritua. ICI-a baliogabetzen duten hartzaile sistema ezberdin proposatu dira, Turbo sistema barne, non BP (belief propagation) detektagailua, soft BEM estimazioa eta LDPC (low-density parity check ) deskodetzailea uztartzen diren. Ohiko kanal ereduak erabilita, simulazio emaitzak aurkeztu dira, proposatutako hartzaile sistemak mugikortasun handiko kasuetan harrera ona dutela erakutsiz, 0.5 Doppler maiztasun normalizaturaino.Esta tesis doctoral analiza y propone diferentes técnicas de estimación de canal para receptores DVB (Digital Video Broadcasting) con movilidad moderada y alta, centrándose en el estándar de segunda generación DVB-T2 (Digital Video Broadcasting - Terrestrial 2 ) y en el próximó estándar DVB-NGH (Digital Video Broadcasting - Next Generation Handheld ). La movilidad es una de las principales claves de estas especificaciones, que tratan de lidiar con el reto de permitir la recepción de señal HDTV (high definition television) en receptores móviles. En escenarios de alta movilidad, la respuesta del canal varía dentro de un símbolo OFDM (orthogonal frequency-division multiplexing ) y las subportadoras ya no son ortogonales, lo que genera la llamada ICI (inter-carrier interference), deteriorando el rendimiento de los receptores severamente. Por lo tanto, con el fin de decodificar correctamente los datos transmitidos, detectores capaces de suprimir la ICI y una precisa CSI (channel state information), incluyendo los términos de ICI, son necesarios en el receptor. Con el objetivo de reducir el número de parámetros necesarios para dicha estimación de canal, y al mismo tiempo garantizar una CSI precisa, la técnica de estimación BEM (basis expansion model) ha sido analizada y propuesta para identificar el canal con ICI en receptores DVB-T2 de alta movilidad. Además se ha propuesto una estructura de pilotos basada en clústers, comparando su rendimiento con los patrones de pilotos establecidos en el estándar. Se han propuesto diferentes sistemas de recepción que cancelan ICI en combinación con la estimación BEM, incluyendo un esquema Turbo que incluye un detector BP (belief propagation), un estimador BEM soft y un decodificador LDPC (low-density parity check). Se han presentado resultados numéricos para los modelos de canal más comunes, demostrando que los sistemas de recepción propuestos permiten la decodificación correcta de la señal incluso en receptores con movilidad muy alta (hasta 0,5 de frecuencia de Doppler normalizada)

    Analysis and Design of Algorithms for the Improvement of Non-coherent Massive MIMO based on DMPSK for beyond 5G systems

    Get PDF
    Mención Internacional en el título de doctorNowadays, it is nearly impossible to think of a service that does not rely on wireless communications. By the end of 2022, mobile internet represented a 60% of the total global online traffic. There is an increasing trend both in the number of subscribers and in the traffic handled by each subscriber. Larger data rates, smaller extreme-to-extreme (E2E) delays and greater number of devices are current interests for the development of mobile communications. Furthermore, it is foreseen that these demands should also be fulfilled in scenarios with stringent conditions, such as very fast varying wireless communications channels (either in time or frequency) or scenarios with power constraints, mainly found when the equipment is battery powered. Since most of the wireless communications techniques and standards rely on the fact that the wireless channel is somehow characterized or estimated to be pre or post-compensated in transmission (TX) or reception (RX), there is a clear problem when the channels vary rapidly or the available power is constrained. To estimate the wireless channel and obtain the so-called channel state information (CSI), some of the available resources (either in time, frequency or any other dimension), are utilized by including known signals in the TX and RX typically known as pilots, thus avoiding their use for data transmission. If the channels vary rapidly, they must be estimated many times, which results in a very low data efficiency of the communications link. Also, in case the power is limited or the wireless link distance is large, the resulting signal-tointerference- plus-noise ratio (SINR) will be low, which is a parameter that is directly related to the quality of the channel estimation and the performance of the data reception. This problem is aggravated in massive multiple-input multiple-output (massive MIMO), which is a promising technique for future wireless communications since it can increase the data rates, increase the reliability and cope with a larger number of simultaneous devices. In massive MIMO, the base station (BS) is typically equipped with a large number of antennas that are coordinated. In these scenarios, the channels must be estimated for each antenna (or at least for each user), and thus, the aforementioned problem of channel estimation aggravates. In this context, algorithms and techniques for massive MIMO without CSI are of interest. This thesis main topic is non-coherent massive multiple-input multiple-output (NC-mMIMO) which relies on the use of differential M-ary phase shift keying (DMPSK) and the spatial diversity of the antenna arrays to be able to detect the useful transmitted data without CSI knowledge. On the one hand, hybrid schemes that combine the coherent and non-coherent schemes allowing to get the best of both worlds are proposed. These schemes are based on distributing the resources between non-coherent (NC) and coherent data, utilizing the NC data to estimate the channel without using pilots and use the estimated channel for the coherent data. On the other hand, new constellations and user allocation strategies for the multi-user scenario of NC-mMIMO are proposed. The new constellations are better than the ones in the literature and obtained using artificial intelligence techniques, more concretely evolutionary computation.This work has received funding from the European Union Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie ETN TeamUp5G, grant agreement No. 813391. The PhD student was the Early Stage Researcher (ESR) number 2 of the project. This work has also received funding from the Spanish National Project IRENE-EARTH (PID2020-115323RB-C33) (MINECO/AEI/FEDER, UE), which funded the work of some coauthors.Programa de Doctorado en Multimedia y Comunicaciones por la Universidad Carlos III de Madrid y la Universidad Rey Juan CarlosPresidente: Luis Castedo Ribas.- Secretario: Matilde Pilar Sánchez Fernández.- Vocal: Eva Lagunas Targaron
    corecore