Systematic Comparison of HF CMOS Transconductors

Transconductors are commonly used as active elements in high-frequency (HF) filters, amplifiers, mixers, and oscillators. This paper reviews transconductor design by focusing on the V-I kernel that determines the key transconductor properties. Based on bandwidth considerations, simple V-I kernels with few or no internal nodes are preferred. In a systematic way, virtually all simple kernels published in literature are generated. This is done in two steps: 1) basic 3-terminal transconductors are covered and 2) then five different techniques to combine two of them in a composite V-I kernel. In order to compare transconductors in a fair way, a normalized signal-to-noise ratio (NSNR) is defined. The basic V-I kernels and the five classes of composite V-I kernels are then compared, leading to insight in the key mechanisms that affect NSNR. Symbolic equations are derived to estimate NSNR, while simulations with more advanced MOSFET models verify the results. The results show a strong tradeoff between NSNR and transconductance tuning range. Resistively generated MOSFETs render the best NSNR results and are robust for future technology developments

Single-amplifier integrator-based low power CMOS filter for video frequency applications

“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”This paper describes a new low power fully differential second-order continuous-time low pass filter for use at video frequencies. The filter uses a single active device in combination with MOSFET resistors and grounded capacitors to achieve very low power consumption, small chip area and large dynamic range. The ideal integrator is realised using an internally compensated opamp consisting of only current mirrors and voltage buffers, whilst the lossy integrator is implemented by a single passive RC circuit. The filter has been simulated using a CMOS process. Results show that with a single 5 V power supply, cut-off frequency can be tuned from 3.5 MHz to 8 MHz, dynamic range is better than 67 dB, and power consumption is less than 1.7 mW

CMOS design of chaotic oscillators using state variables: a monolithic Chua's circuit

This paper presents design considerations for monolithic implementation of piecewise-linear (PWL) dynamic systems in CMOS technology. Starting from a review of available CMOS circuit primitives and their respective merits and drawbacks, the paper proposes a synthesis approach for PWL dynamic systems, based on state-variable methods, and identifies the associated analog operators. The GmC approach, combining quasi-linear VCCS's, PWL VCCS's, and capacitors is then explored regarding the implementation of these operators. CMOS basic building blocks for the realization of the quasi-linear VCCS's and PWL VCCS's are presented and applied to design a Chua's circuit IC. The influence of GmC parasitics on the performance of dynamic PWL systems is illustrated through this example. Measured chaotic attractors from a Chua's circuit prototype are given. The prototype has been fabricated in a 2.4- mu m double-poly n-well CMOS technology, and occupies 0.35 mm/sup 2/, with a power consumption of 1.6 mW for a +or-2.5-V symmetric supply. Measurements show bifurcation toward a double-scroll Chua's attractor by changing a bias current

A Low-Voltage Electronically Tunable MOSFET-C Voltage-Mode First-Order All-Pass Filter Design

This paper presents a simple electronically tunable voltage-mode first-order all-pass filter realization with MOSFET-C technique. In comparison to the classical MOSFET-C filter circuits that employ active elements including large number of transistors the proposed circuit is only composed of a single two n-channel MOSFET-based inverting voltage buffer, three passive components, and one NMOS-based voltage-controlled resistor, which is with advantage used to electronically control the pole frequency of the filter in range 103 kHz to 18.3 MHz. The proposed filter is also very suitable for low-voltage operation, since between its supply rails it uses only two MOSFETs. In the paper the effect of load is investigated. In addition, in order to suppress the effect of non-zero output resistance of the inverting voltage buffer, two compensation techniques are also introduced. The theoretical results are verified by SPICE simulations using PTM 90 nm level-7 CMOS process BSIM3v3 parameters, where +/- 0.45 V supply voltages are used. Moreover, the behavior of the proposed filter was also experimentally measured using readily available array transistors CD4007UB by Texas Instruments

A 0.18μm CMOS low-noise elliptic low-pass continuous-time filter

This paper presents a seventh order low-pass continuous-time elliptic filter for use in a high-performance wireline communication receiver. As an additional attribute, the filter provides programmable boost in the pass-band to counteract high frequency components attenuation. The filter shows a nominal cutoff frequency of fc=34 MHz , less than 1dB ripple in the pass-band, and a maximum stop-band rejection of 65dB. The filter also exhibits low noise feature (peak root spectral noise density below 56nV√Hz) and high linearity (more than 64dB of MTPR for a DMT signal of 0.5Vpp amplitude). It has been designed in a 0.18μm CMOS technology and it is compliant with industrial operation conditions (-40 to 85° C temperature variation and ± 5% power supply deviation). Simulations show a typical power consumption of 450 mW @ 1.8V supply.Ministerio de Ciencia y Tecnología TIC2003-0235

Programmable low-voltage continuous-time filter for audio applications

The implementation of a continuous-time filter (CTF) useful for audio frequency applications is presented in this paper. The filter functions can be programmed and tuned with two independent control variables. The filter here proposed has been designed to work at 1.5 V of power supply and at a maximum of 0.5 /spl mu/A/OTA for the worst case current consumption. Electrical simulations of a Tow-Thomas biquad (TTB) show the possibility of obtaining low-pass and band-pass filter functions over the 10 Hz-40 kHz frequency range by changing a control current over four decades.Comisión Interministerial de Ciencia y Tecnología TIC-97-064

The design of active resistors and transductors in a CMOS technology

Merged with duplicate record 10026.1/2618 on 07.20.2017 by CS (TIS)This thesis surveys linearisation techniques for implementing monolithic MOS active resistors and transconductors, and investigates the design of linear tunable resistors and transconductors. Improving linearity and tunability in the presence of non-ideal factors such as bulk modulation, mobility-degradation effects and mismatch of transistors is a principal objective. A family of new non-saturation-mode resistors and two novel saturation-mode transconductors are developed. Where possible, approximate analytical expressions are derived to explain the principles of operation. Performance comparisons of the new structures are made with other well-known circuits and their relative advantages and disadvantages evaluated. Experimental and simulation results are presented which validate the proposed linearisation techniques. It is shown that the proposed family of resistors offers improved linearity whilst the transconductors combine extended tunability with low distortion. Continuous-time filter examples are given to demonstrate the potential of these circuits for application in analogue signal-processing tasks.GEC Plessey Semiconductors, Plymout