35,753 research outputs found
Agile Autonomous Driving using End-to-End Deep Imitation Learning
We present an end-to-end imitation learning system for agile, off-road
autonomous driving using only low-cost sensors. By imitating a model predictive
controller equipped with advanced sensors, we train a deep neural network
control policy to map raw, high-dimensional observations to continuous steering
and throttle commands. Compared with recent approaches to similar tasks, our
method requires neither state estimation nor on-the-fly planning to navigate
the vehicle. Our approach relies on, and experimentally validates, recent
imitation learning theory. Empirically, we show that policies trained with
online imitation learning overcome well-known challenges related to covariate
shift and generalize better than policies trained with batch imitation
learning. Built on these insights, our autonomous driving system demonstrates
successful high-speed off-road driving, matching the state-of-the-art
performance.Comment: 13 pages, Robotics: Science and Systems (RSS) 201
Predictive current control of asynchronous machines by optimizing the switching moments
In this paper a model-based predictive control (MBPC) scheme for the current control of induction machines is presented. The controller directly selects the optimal switch state of the inverter. The proposed scheme uses a longer prediction horizon and a limited amount of optimal switching instants to reduce the average switching frequency. The next iteration of the MBPC-scheme is performed at the established optimal switching instant, as such suppressing the receding horizon property for short time spans.
The proposed method is compared to a more conventional MBPC-scheme with a very short prediction horizon. Both simulations and experiments clearly show a significant reduction in average switching frequency. However, with a reduction in switching frequency the torque ripple is increased. To correctly asses the properties of the different schemes, a key performance indicator is proposed that offers a fair and unbiased comparison in terms of switching frequency and torque ripple
Implementation of Nonlinear Model Predictive Path-Following Control for an Industrial Robot
Many robotic applications, such as milling, gluing, or high precision
measurements, require the exact following of a pre-defined geometric path. In
this paper, we investigate the real-time feasible implementation of model
predictive path-following control for an industrial robot. We consider
constrained output path following with and without reference speed assignment.
We present results from an implementation of the proposed model predictive
path-following controller on a KUKA LWR IV robot.Comment: 8 pages, 3 figures; final revised versio
A survey on fractional order control techniques for unmanned aerial and ground vehicles
In recent years, numerous applications of science and engineering for modeling and control of unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs) systems based on fractional calculus have been realized. The extra fractional order derivative terms allow to optimizing the performance of the systems. The review presented in this paper focuses on the control problems of the UAVs and UGVs that have been addressed by the fractional order techniques over the last decade
A two-dimensional data-driven model for traffic flow on highways
Based on experimental traffic data obtained from German and US highways, we
propose a novel two-dimensional first-order macroscopic traffic flow model. The
goal is to reproduce a detailed description of traffic dynamics for the real
road geometry. In our approach both the dynamic along the road and across the
lanes is continuous. The closure relations, being necessary to complete the
hydrodynamic equation, are obtained by regression on fundamental diagram data.
Comparison with prediction of one-dimensional models shows the improvement in
performance of the novel model.Comment: 27 page
Recommended from our members
Development of Eco-Friendly Ramp Control for Connected and Automated Electric Vehicles
With on-board sensors such as camera, radar, and Lidar, connected and automated vehicles (CAVs) can sense the surrounding environment and be driven autonomously and safely by themselves without colliding into other objects on the road. CAVs are also able to communicate with each other and roadside infrastructure via vehicle-to-vehicle and vehicle-to-infrastructure communications, respectively, sharing information on the vehicles’ states, signal phase and timing (SPaT) information, enabling CAVs to make decisions in a collaborative manner. As a typical scenario, ramp control attracts wide attention due to the concerns of safety and mobility in the merging area. In particular, if the line-of-the-sight is blocked (because of grade separation), then neither mainline vehicles nor on-ramp vehicles may well adapt their own dynamics to perform smoothed merging maneuvers. This may lead to speed fluctuations or even shockwave propagating upstream traffic along the corridor, thus potentially increasing the traffic delays and excessive energy consumption. In this project, the research team proposed a hierarchical ramp merging system that not only allowed microscopic cooperative maneuvers for connected and automated electric vehicles on the ramp to merge into mainline traffic flow, but also had controllability of ramp inflow rate, which enabled macroscopic traffic flow control. A centralized optimal control-based approach was proposed to both smooth the merging flow and improve the system-wide mobility of the network. Linear quadratic trackers in both finite horizon and receding horizon forms were developed to solve the optimization problem in terms of path planning and sequence determination, and a microscopic electric vehicle (EV) energy consumption model was applied to estimate the energy consumption. The simulation results confirmed that under the regulated inflow rate, the proposed system was able to avoid potential traffic congestion and improve the mobility (in terms of average speed) as much as 115%, compared to the conventional ramp metering and the ramp without any control approach. Interestingly, for EVs (connected and automated EVs in this study), the improved mobility may not necessarily result in the reduction of energy consumption. The “sweet spot” of average speed ranges from 27–34 mph for the EV models in this study.View the NCST Project Webpag
A Learning-based Stochastic MPC Design for Cooperative Adaptive Cruise Control to Handle Interfering Vehicles
Vehicle to Vehicle (V2V) communication has a great potential to improve
reaction accuracy of different driver assistance systems in critical driving
situations. Cooperative Adaptive Cruise Control (CACC), which is an automated
application, provides drivers with extra benefits such as traffic throughput
maximization and collision avoidance. CACC systems must be designed in a way
that are sufficiently robust against all special maneuvers such as cutting-into
the CACC platoons by interfering vehicles or hard braking by leading cars. To
address this problem, a Neural- Network (NN)-based cut-in detection and
trajectory prediction scheme is proposed in the first part of this paper. Next,
a probabilistic framework is developed in which the cut-in probability is
calculated based on the output of the mentioned cut-in prediction block.
Finally, a specific Stochastic Model Predictive Controller (SMPC) is designed
which incorporates this cut-in probability to enhance its reaction against the
detected dangerous cut-in maneuver. The overall system is implemented and its
performance is evaluated using realistic driving scenarios from Safety Pilot
Model Deployment (SPMD).Comment: 10 pages, Submitted as a journal paper at T-I
Predictive Control of Autonomous Kites in Tow Test Experiments
In this paper we present a model-based control approach for autonomous flight
of kites for wind power generation. Predictive models are considered to
compensate for delay in the kite dynamics. We apply Model Predictive Control
(MPC), with the objective of guiding the kite to follow a figure-of-eight
trajectory, in the outer loop of a two level control cascade. The tracking
capabilities of the inner-loop controller depend on the operating conditions
and are assessed via a frequency domain robustness analysis. We take the
limitations of the inner tracking controller into account by encoding them as
optimisation constraints in the outer MPC. The method is validated on a kite
system in tow test experiments.Comment: The paper has been accepted for publication in the IEEE Control
Systems Letters and is subject to IEEE Control Systems Society copyright.
Upon publication, the copy of record will be available at
http://ieeexplore.ieee.or
- …