A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

An effective AMS Top-Down Methodology Applied to the Design of a Mixed-SignalUWB System-on-Chip

The design of Ultra Wideband (UWB) mixed-signal SoC for localization applications in wireless personal area networks is currently investigated by several researchers. The complexity of the design claims for effective top-down methodologies. We propose a layered approach based on VHDL-AMS for the first design stages and on an intelligent use of a circuit-level simulator for the transistor-level phase. We apply the latter just to one block at a time and wrap it within the system-level VHDL-AMS description. This method allows to capture the impact of circuit-level design choices and non-idealities on system performance. To demonstrate the effectiveness of the methodology we show how the refinement of the design affects specific UWB system parameters such as bit-error rate and localization estimations

Design of a Low Voltage Class AB Variable Gain Amplifier (VGA)

A variable gain amplifier (VGA) is one of the most significant component in many applications such as analog to digital converter (ADC). In communication receiver, VGA is typically employed in a feedback loop to realize an automatic gain control (AGC), to provide constant signal power to baseband analog-to-digital converter (ADC) for unpredictable received signal strengths. Gain range, power consumption and bandwidth of ADC are strongly influenced by the performance of operational amplifier. VGA is the key element for amplifying process in ADC. However, current class AB VGA is experiencing the limit of bandwidth, which is not suitable for high speed automatic gain control AGC. In order to overcome these limitations a high linearity and wide bandwidth of VGA is indispensable. The aim of this research is to get higher gain and larger bandwidth for VGA. In this research, a low cost, low power voltage and wide bandwidth class AB VGA is designed to mitigate this constraint. Superiority of the proposed VGA has been confirmed by circuit simulation using CEDEC 0.18-μm CMOS process with the help of tools from Mentor Graphics in designing a 100-MHz VGA under 1V supply voltage draining total static power consumption less than 125uW. The results show that the circuit is able to work with high linearity and wide bandwidth by varying Rf and Rs. Therefore, the frequency response (Gain) and the wide bandwidth of this class AB VGA is better than previously reported class AB VGA. Consequently, this modified class AB VGA is appropriate for high speed applications

A 14-mW PLL-less receiver in 0.18-μm CMOS for Chinese electronic toll collection standard

This is the accepted manuscript version of the following article: Xiaofeng He, et al., “A 14-mW PLL-less receiver in 0.18-μm CMOS for Chinese electronic toll collection standard”, IEEE Transactions on Circuits and Systems II: Express Briefs, Vol. 61(10): 763-767, August 2014. The final published version is available at: http://ieeexplore.ieee.org/document/6871304/ © 2014 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.The design of a 14-mW receiver without phase-locked loop for the Chinese electronic toll collection (ETC) system in a standard 0.18-μm CMOS process is presented in this brief. Since the previously published work was mainly based on vehicle-powered systems, low power consumption was not the primary goal of such a system. In contrast, the presented system is designed for a battery-powered system. Utilizing the presented receiver architecture, the entire receiver only consumes 7.8 mA, at the supply voltage of 1.8 V, which indicates a power saving of at least 38% compared with other state-of-the-art designs for the same application. To verify the performance, the bit error rate is measured to be better than 10-6, which well satisfies the Chinese ETC standard. Moreover, the sensitivity of the designed receiver can be readjusted to -50 dBm, which is required by the standard.Peer reviewe

Optical receiver bandwidth enhancement using bootstrap transimpedance amplification technique

Optical wireless link operates in high noise environments owing to ambient conditions such as sun for outdoors and fluorescent for indoors. The performance of free-space optics is subjected to several atmospheric factors like environmental temperature, fog, smoke, haze and rain. Signal-to-noise ratio (SNR) can vary significantly with the distance and ambient noise. Limited range due to ambient noise is the dominant noise. A good sensitivity and a broad bandwidth will invariably use a small area photodiode where the aperture is small. However, freespace optics requires a large aperture and thus, the receiver is required to have a large collection area, which may be achieved by using a large area photodetector and large filter. However, large area of photodetector produces a high input capacitance that will be reduced the bandwidth. Typical large photodetection area commercial detectors has capacitance are around 100-300pF compared to 50pF in fiber link. Hence, techniques to reduce the effective detector capacitance are required in order to achieve a low noise and wide bandwidth design. In this project, modeling and analysis the bootstrap transimpedance amplifier (BTA) of front-end receiver for input capacitance reduction has been simulated. This technique improved the conventional transimpedance amplifier (TIA) bandwidth up to 1000 times with an effective capacitance reduction technique for optical wireless detecto

A VHDL-AMS Simulation Environment for an UWB Impulse Radio Transceiver

Ultra-Wide-Band (UWB) communication based on the impulse radio paradigm is becoming increasingly popular. According to the IEEE 802.15 WPAN Low Rate Alternative PHY Task Group 4a, UWB will play a major role in localization applications, due to the high time resolution of UWB signals which allow accurate indirect measurements of distance between transceivers. Key for the successful implementation of UWB transceivers is the level of integration that will be reached, for which a simulation environment that helps take appropriate design decisions is crucial. Owing to this motivation, in this paper we propose a multiresolution UWB simulation environment based on the VHDL-AMS hardware description language, along with a proper methodology which helps tackle the complexity of designing a mixed-signal UWB System-on-Chip. We applied the methodology and used the simulation environment for the specification and design of an UWB transceiver based on the energy detection principle. As a by-product, simulation results show the effectiveness of UWB in the so-called ranging application, that is the accurate evaluation of the distance between a couple of transceivers using the two-way-ranging metho

Um amplificador de transimpedância de ganho variável para aplicação em osciladores baseados em MEMS

Orientador: José Alexandre DinizDissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de ComputaçãoResumo: Um amplificador de transimpedância (TIA) de ganho variável é apresentado. Implementado em tecnologia 0,18 'mi'm, o projeto relatado possui a finalidade de prover um amplificador de sustentação para osciladores baseados em ressonadores do tipo MEMS (Micro-Electro-Mechanical System). Entre outros, as peculiaridades de projeto envolvem um desafiante compromisso entre Ganho, Largura de Banda, Ruído e Consumo de potência. Sendo assim, o amplificador foi implementado através do cascateamento de quatro estágios de ganho similares, lançando-se mão de realimentação do tipo shunt-shunt para diminuir as impedâncias de entrada e saída. Através do emprego de um estágio de ganho variável, uma alta faixa dinâmica de ganho é alcançada (53 dB), com um ganho máximo de transimpedância de 118 dB'ômega'...Observação: O resumo, na íntegra, poderá ser visualizado no texto completo da tese digitalAbstract: A variable gain Transimpedance Amplifier (TIA) is presented. Realized in 0.18 'mi'm technology, this amplifier was conceived with the purpose of providing oscillation sustaining for Micro-Electro-Mechanical System (MEMS) based oscillators. Facing a quite challenging trade-off between Gain, Bandwidth, Noise and Power consumption, the TIA was implemented through the cascade of four similar gain stages, with the application of shunt-shunt feedback to lower both input and output resistances. With the employment of a variable-gain stage, this TIA presents a large gain tunability of 53 dB, with a also large maximum transimpedance gain of 118 dB'omega'...Note: The complete abstract is available with the full electronic documentMestradoEletrônica, Microeletrônica e OptoeletrônicaMestre em Engenharia Elétric

Software-Defined Lighting.

For much of the past century, indoor lighting has been based on incandescent or gas-discharge technology. But, with LED lighting experiencing a 20x/decade increase in flux density, 10x/decade decrease in cost, and linear improvements in luminous efficiency, solid-state lighting is finally cost-competitive with the status quo. As a result, LED lighting is projected to reach over 70% market penetration by 2030. This dissertation claims that solid-state lighting’s real potential has been barely explored, that now is the time to explore it, and that new lighting platforms and applications can drive lighting far beyond its roots as an illumination technology. Scaling laws make solid-state lighting competitive with conventional lighting, but two key features make solid-state lighting an enabler for many new applications: the high switching speeds possible using LEDs and the color palettes realizable with Red-Green-Blue-White (RGBW) multi-chip assemblies. For this dissertation, we have explored the post-illumination potential of LED lighting in applications as diverse as visible light communications, indoor positioning, smart dust time synchronization, and embedded device configuration, with an eventual eye toward supporting all of them using a shared lighting infrastructure under a unified system architecture that provides software-control over lighting. To explore the space of software-defined lighting (SDL), we design a compact, flexible, and networked SDL platform to allow researchers to rapidly test new ideas. Using this platform, we demonstrate the viability of several applications, including multi-luminaire synchronized communication to a photodiode receiver, communication to mobile phone cameras, and indoor positioning using unmodified mobile phones. We show that all these applications and many other potential applications can be simultaneously supported by a single lighting infrastructure under software control.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/111482/1/samkuo_1.pd

Study of Adjustable Gains for Control of Oscillation Frequency and Oscillation Condition in 3R-2C Oscillator

An idea of adjustable gain in order to obtain controllable features is very useful for design of tuneable oscillators. Several active elements with adjustable properties (current and voltage gain) are discussed in this paper. Three modified oscillator conceptions that are quite simple, directly electronically adjustable, providing independent control of oscillation condition and frequency were designed. Positive and negative aspects of presented method of control are discussed. Expected assumptions of adjustability are verified experimentally on one of the presented solution