Adjusting Laser Injections for Fully Controlled Faults

Hardware characterizations of integrated circuits have been evolving rapidly with the advent of more precise, sophisticated and cost-efficient tools. In this paper we describe how the fine tuning of a laser source has been used to characterize, set and reset the state of registers in a 90 nm chip. By adjusting the incident laser beam’s location, it is possible to choose to switch any register value from ‘ 0 ’ to ‘ 1 ’ or vice-versa by targeting the PMOS side or the NMOS side. Plus, we show how to clear a register by selecting a laser beam’s power. With the help of imaging techniques, we are able to explain the underlying phenomenon and provide a direct link between the laser mapping and the physical gate structure. Thus, we correlate the localization of laser fault injections with implementations of the PMOS and NMOS areas in the silicon substrate. This illustrates to what extent laser beams can be used to monitor the bits stored within registers, with adverse consequences in terms of security evaluation of integrated circuits

Interconnect yield analysis and fault tolerance for field programmable gate arrays

Imperial Users onl

Techniques for Improving Security and Trustworthiness of Integrated Circuits

The integrated circuit (IC) development process is becoming increasingly vulnerable to malicious activities because untrusted parties could be involved in this IC development flow. There are four typical problems that impact the security and trustworthiness of ICs used in military, financial, transportation, or other critical systems: (i) Malicious inclusions and alterations, known as hardware Trojans, can be inserted into a design by modifying the design during GDSII development and fabrication. Hardware Trojans in ICs may cause malfunctions, lower the reliability of ICs, leak confidential information to adversaries or even destroy the system under specifically designed conditions. (ii) The number of circuit-related counterfeiting incidents reported by component manufacturers has increased significantly over the past few years with recycled ICs contributing the largest percentage of the total reported counterfeiting incidents. Since these recycled ICs have been used in the field before, the performance and reliability of such ICs has been degraded by aging effects and harsh recycling process. (iii) Reverse engineering (RE) is process of extracting a circuit’s gate-level netlist, and/or inferring its functionality. The RE causes threats to the design because attackers can steal and pirate a design (IP piracy), identify the device technology, or facilitate other hardware attacks. (iv) Traditional tools for uniquely identifying devices are vulnerable to non-invasive or invasive physical attacks. Securing the ID/key is of utmost importance since leakage of even a single device ID/key could be exploited by an adversary to hack other devices or produce pirated devices. In this work, we have developed a series of design and test methodologies to deal with these four challenging issues and thus enhance the security, trustworthiness and reliability of ICs. The techniques proposed in this thesis include: a path delay fingerprinting technique for detection of hardware Trojans, recycled ICs, and other types counterfeit ICs including remarked, overproduced, and cloned ICs with their unique identifiers; a Built-In Self-Authentication (BISA) technique to prevent hardware Trojan insertions by untrusted fabrication facilities; an efficient and secure split manufacturing via Obfuscated Built-In Self-Authentication (OBISA) technique to prevent reverse engineering by untrusted fabrication facilities; and a novel bit selection approach for obtaining the most reliable bits for SRAM-based physical unclonable function (PUF) across environmental conditions and silicon aging effects

Innovative Techniques for Testing and Diagnosing SoCs

We rely upon the continued functioning of many electronic devices for our everyday welfare, usually embedding integrated circuits that are becoming even cheaper and smaller with improved features. Nowadays, microelectronics can integrate a working computer with CPU, memories, and even GPUs on a single die, namely System-On-Chip (SoC). SoCs are also employed on automotive safety-critical applications, but need to be tested thoroughly to comply with reliability standards, in particular the ISO26262 functional safety for road vehicles. The goal of this PhD. thesis is to improve SoC reliability by proposing innovative techniques for testing and diagnosing its internal modules: CPUs, memories, peripherals, and GPUs. The proposed approaches in the sequence appearing in this thesis are described as follows: 1. Embedded Memory Diagnosis: Memories are dense and complex circuits which are susceptible to design and manufacturing errors. Hence, it is important to understand the fault occurrence in the memory array. In practice, the logical and physical array representation differs due to an optimized design which adds enhancements to the device, namely scrambling. This part proposes an accurate memory diagnosis by showing the efforts of a software tool able to analyze test results, unscramble the memory array, map failing syndromes to cell locations, elaborate cumulative analysis, and elaborate a final fault model hypothesis. Several SRAM memory failing syndromes were analyzed as case studies gathered on an industrial automotive 32-bit SoC developed by STMicroelectronics. The tool displayed defects virtually, and results were confirmed by real photos taken from a microscope. 2. Functional Test Pattern Generation: The key for a successful test is the pattern applied to the device. They can be structural or functional; the former usually benefits from embedded test modules targeting manufacturing errors and is only effective before shipping the component to the client. The latter, on the other hand, can be applied during mission minimally impacting on performance but is penalized due to high generation time. However, functional test patterns may benefit for having different goals in functional mission mode. Part III of this PhD thesis proposes three different functional test pattern generation methods for CPU cores embedded in SoCs, targeting different test purposes, described as follows: a. Functional Stress Patterns: Are suitable for optimizing functional stress during I Operational-life Tests and Burn-in Screening for an optimal device reliability characterization b. Functional Power Hungry Patterns: Are suitable for determining functional peak power for strictly limiting the power of structural patterns during manufacturing tests, thus reducing premature device over-kill while delivering high test coverage c. Software-Based Self-Test Patterns: Combines the potentiality of structural patterns with functional ones, allowing its execution periodically during mission. In addition, an external hardware communicating with a devised SBST was proposed. It helps increasing in 3% the fault coverage by testing critical Hardly Functionally Testable Faults not covered by conventional SBST patterns. An automatic functional test pattern generation exploiting an evolutionary algorithm maximizing metrics related to stress, power, and fault coverage was employed in the above-mentioned approaches to quickly generate the desired patterns. The approaches were evaluated on two industrial cases developed by STMicroelectronics; 8051-based and a 32-bit Power Architecture SoCs. Results show that generation time was reduced upto 75% in comparison to older methodologies while increasing significantly the desired metrics. 3. Fault Injection in GPGPU: Fault injection mechanisms in semiconductor devices are suitable for generating structural patterns, testing and activating mitigation techniques, and validating robust hardware and software applications. GPGPUs are known for fast parallel computation used in high performance computing and advanced driver assistance where reliability is the key point. Moreover, GPGPU manufacturers do not provide design description code due to content secrecy. Therefore, commercial fault injectors using the GPGPU model is unfeasible, making radiation tests the only resource available, but are costly. In the last part of this thesis, we propose a software implemented fault injector able to inject bit-flip in memory elements of a real GPGPU. It exploits a software debugger tool and combines the C-CUDA grammar to wisely determine fault spots and apply bit-flip operations in program variables. The goal is to validate robust parallel algorithms by studying fault propagation or activating redundancy mechanisms they possibly embed. The effectiveness of the tool was evaluated on two robust applications: redundant parallel matrix multiplication and floating point Fast Fourier Transform

Analysis and Test of the Effects of Single Event Upsets Affecting the Configuration Memory of SRAM-based FPGAs

SRAM-based FPGAs are increasingly relevant in a growing number of safety-critical application fields, ranging from automotive to aerospace. These application fields are characterized by a harsh radiation environment that can cause the occurrence of Single Event Upsets (SEUs) in digital devices. These faults have particularly adverse effects on SRAM-based FPGA systems because not only can they temporarily affect the behaviour of the system by changing the contents of flip-flops or memories, but they can also permanently change the functionality implemented by the system itself, by changing the content of the configuration memory. Designing safety-critical applications requires accurate methodologies to evaluate the system’s sensitivity to SEUs as early as possible during the design process. Moreover it is necessary to detect the occurrence of SEUs during the system life-time. To this purpose test patterns should be generated during the design process, and then applied to the inputs of the system during its operation. In this thesis we propose a set of software tools that could be used by designers of SRAM-based FPGA safety-critical applications to assess the sensitivity to SEUs of the system and to generate test patterns for in-service testing. The main feature of these tools is that they implement a model of SEUs affecting the configuration bits controlling the logic and routing resources of an FPGA device that has been demonstrated to be much more accurate than the classical stuck-at and open/short models, that are commonly used in the analysis of faults in digital devices. By keeping this accurate fault model into account, the proposed tools are more accurate than similar academic and commercial tools today available for the analysis of faults in digital circuits, that do not take into account the features of the FPGA technology.. In particular three tools have been designed and developed: (i) ASSESS: Accurate Simulator of SEuS affecting the configuration memory of SRAM-based FPGAs, a simulator of SEUs affecting the configuration memory of an SRAM-based FPGA system for the early assessment of the sensitivity to SEUs; (ii) UA2TPG: Untestability Analyzer and Automatic Test Pattern Generator for SEUs Affecting the Configuration Memory of SRAM-based FPGAs, a static analysis tool for the identification of the untestable SEUs and for the automatic generation of test patterns for in-service testing of the 100% of the testable SEUs; and (iii) GABES: Genetic Algorithm Based Environment for SEU Testing in SRAM-FPGAs, a Genetic Algorithm-based Environment for the generation of an optimized set of test patterns for in-service testing of SEUs. The proposed tools have been applied to some circuits from the ITC’99 benchmark. The results obtained from these experiments have been compared with results obtained by similar experiments in which we considered the stuck-at fault model, instead of the more accurate model for SEUs. From the comparison of these experiments we have been able to verify that the proposed software tools are actually more accurate than similar tools today available. In particular the comparison between results obtained using ASSESS with those obtained by fault injection has shown that the proposed fault simulator has an average error of 0:1% and a maximum error of 0:5%, while using a stuck-at fault simulator the average error with respect of the fault injection experiment has been 15:1% with a maximum error of 56:2%. Similarly the comparison between the results obtained using UA2TPG for the accurate SEU model, with the results obtained for stuck-at faults has shown an average difference of untestability of 7:9% with a maximum of 37:4%. Finally the comparison between fault coverages obtained by test patterns generated for the accurate model of SEUs and the fault coverages obtained by test pattern designed for stuck-at faults, shows that the former detect the 100% of the testable faults, while the latter reach an average fault coverage of 78:9%, with a minimum of 54% and a maximum of 93:16%

Multi-criteria optimization for energy-efficient multi-core systems-on-chip

The steady down-scaling of transistor dimensions has made possible the evolutionary progress leading to today’s high-performance multi-GHz microprocessors and core based System-on-Chip (SoC) that offer superior performance, dramatically reduced cost per function, and much-reduced physical size compared to their predecessors. On the negative side, this rapid scaling however also translates to high power densities, higher operating temperatures and reduced reliability making it imperative to address design issues that have cropped up in its wake. In particular, the aggressive physical miniaturization have increased CMOS fault sensitivity to the extent that many reliability constraints pose threat to the device normal operation and accelerate the onset of wearout-based failures. Among various wearout-based failure mechanisms, Negative biased temperature instability (NBTI) has been recognized as the most critical source of device aging. The urge of reliable, low-power circuits is driving the EDA community to develop new design techniques, circuit solutions, algorithms, and software, that can address these critical issues. Unfortunately, this challenge is complicated by the fact that power and reliability are known to be intrinsically conflicting metrics: traditional solutions to improve reliability such as redundancy, increase of voltage levels, and up-sizing of critical devices do contrast with traditional low-power solutions, which rely on compact architectures, scaled supply voltages, and small devices. This dissertation focuses on methodologies to bridge this gap and establishes an important link between low-power solutions and aging effects. More specifically, we proposed new architectural solutions based on power management strategies to enable the design of low-power, aging aware cache memories. Cache memories are one of the most critical components for warranting reliable and timely operation. However, they are also more susceptible to aging effects. Due to symmetric structure of a memory cell, aging occurs regardless of the fact that a cell (or word) is accessed or not. Moreover, aging is a worst-case matric and line with worst-case access pattern determines the aging of the entire cache. In order to stop the aging of a memory cell, it must be put into a proper idle state when a cell (or word) is not accessed which require proper management of the idleness of each atomic unit of power management. We have proposed several reliability management techniques based on the idea of cache partitioning to alleviate NBTI-induced aging and obtain joint energy and lifetime benefits. We introduce graceful degradation mechanism which allows different cache blocks into which a cache is partitioned to age at different rates. This implies that various sub-blocks become unreliable at different times, and the cache keeps functioning with reduced efficiency. We extended the capabilities of this architecture by integrating the concept of reconfigurable caches to maintain the performance of the cache throughout its lifetime. By this strategy, whenever a block becomes unreliable, the remaining cache is reconfigured to work as a smaller size cache with only a marginal degradation of performance. Many mission-critical applications require guaranteed lifetime of their operations and therefore the hardware implementing their functionality. Such constraints are usually enforced by means of various reliability enhancing solutions mostly based on redundancy which are not energy-friendly. In our work, we have proposed a novel cache architecture in which a smart use of cache partitions for redundancy allows us to obtain cache that meet a desired lifetime target with minimal energy consumption

No Place to Hide: Contactless Probing of Secret Data on FPGAs

Field Programmable Gate Arrays (FPGAs) have been the target of different physical attacks in recent years. Many different countermeasures have already been integrated into these devices to mitigate the existing vulnerabilities. However, there has not been enough attention paid to semi-invasive attacks from the IC backside due to the following reasons. First, the conventional semi-invasive attacks from the IC backside --- such as laser fault injection and photonic emission analysis --- cannot be scaled down without further effort to the very latest nanoscale technologies of modern FPGAs and programmable SoCs. Second, the more advanced solutions for secure storage, such as controlled Physically Unclonable Functions (PUFs), make the conventional memory-readout techniques almost impossible. In this paper, however, novel approaches have been explored: Attacks based on Laser Voltage Probing (LVP) and its derivatives, as commonly used in Integrated Circuit (IC) debug for nanoscale low voltage technologies, are successfully launched against a $60$ nanometer technology FPGA. We discuss how these attacks can be used to break modern bitstream encryption implementations. Our attacks were carried out on a Proof-of-Concept PUF-based key generation implementation. To the best of our knowledge this is the first time that LVP is used to perform an attack on secure ICs

CDM Robust & Low Noise ESD protection circuits

In spite of significant progress during last couple of decades, ESD still affects production yields, manufacturing costs, product quality, product reliability and profitability. The objective of an ESD protection circuit is to create a harmless shunting path for the static electricity before it damages the sensitive electronic circuits. As the devices are scaling down, while ESD energy remains the same, VLSIs are becoming more vulnerable to ESD stress. This higher susceptibility to ESD damage is due to thinner gate oxides and shallower junctions. Furthermore, higher operating frequency of the scaled technologies enforces lower parasitic capacitance of the ESD protection circuits. Hence, increasing the robustness of the ESD protection circuits with minimum additional parasitic capacitance is the main challenge in state of the art CMOS processes. Furthermore with scaling, the integration of analog blocks such as ADC, PLL’s, DLL’s, oscillator etc. on digital chips has provided cheap system on chip (SOC) solutions. However, when analog and digital chip are combined into single mixed-signal chip, on-chip noise coupling from the digital to the analog circuitry through ESD protection circuits becomes a big concern. Thus, increasing supply noise isolation while ensuring the ESD protection robustness is also a big challenge. In this thesis, several ESD protection circuits and devices have been proposed to address the critical issues like increased leakage current, slower turn-on time of devices, increased susceptibility to power supply isolation etc. The proposed ESD protection circuits/devices have been classified into two categories: Pad based ESD protection in which the ESD protection circuits are placed in the I/O pads, and Rail based ESD in which ESD protection circuit is placed between power supplies. In our research, both these aspects have been investigated. The Silicon Controlled Rectifier (SCR) based devices have been used for Pad ESD protection as they have highest ESD protection level per unit area. Two novel devices Darlington based SCR (DSCR) and NMOS Darlington based SCR (NMOS-DSCR) having faster turn-on time, lower first breakdown voltage and low capacitance have been proposed. The transient clamps have been investigated and optimized for Rail based ESD protection. In this research, we have addressed the issue of leakage current in transient clamps. A methodology has been purposed to reduce the leakage current by more than 200,000 times without having major impact on the ESD performance. Also, the issue of noise coupling from digital supply to analog supply through the ESD protection circuits has been addressed. A new transient clamp has been proposed to increase the power supply noise isolation. Finally, a new methodology of placement of analog circuit with respect to transient clamp has been proposed to further increase the power supply noise isolation

Analyse und Erweiterung eines fehler-toleranten NoC für SRAM-basierte FPGAs in Weltraumapplikationen

Data Processing Units for scientific space mission need to process ever higher volumes of data and perform ever complex calculations. But the performance of available space-qualified general purpose processors is just in the lower three digit megahertz range, which is already insufficient for some applications. As an alternative, suitable processing steps can be implemented in hardware on a space-qualified SRAM-based FPGA. However, suitable devices are susceptible against space radiation. At the Institute for Communication and Network Engineering a fault-tolerant, network-based communication architecture was developed, which enables the construction of processing chains on the basis of different processing modules within suitable SRAM-based FPGAs and allows the exchange of single processing modules during runtime, too. The communication architecture and its protocol shall isolate non SEU mitigated or just partial SEU mitigated modules affected by radiation-induced faults to prohibit the propagation of errors within the remaining System-on-Chip. In the context of an ESA study, this communication architecture was extended with further components and implemented in a representative hardware platform. Based on the acquired experiences during the study, this work analyses the actual fault-tolerance characteristics as well as weak points of this initial implementation. At appropriate locations, the communication architecture was extended with mechanisms for fault-detection and fault-differentiation as well as with a hardware-based monitoring solution. Both, the former measures and the extension of the employed hardware-platform with selective fault-injection capabilities for the emulation of radiation-induced faults within critical areas of a non SEU mitigated processing module, are used to evaluate the effects of radiation-induced faults within the communication architecture. By means of the gathered results, further measures to increase fast detection and isolation of faulty nodes are developed, selectively implemented and verified. In particular, the ability of the communication architecture to isolate network nodes without SEU mitigation could be significantly improved.Instrumentenrechner für wissenschaftliche Weltraummissionen müssen ein immer höheres Datenvolumen verarbeiten und immer komplexere Berechnungen ausführen. Die Performanz von verfügbaren qualifizierten Universalprozessoren liegt aber lediglich im unteren dreistelligen Megahertz-Bereich, was für einige Anwendungen bereits nicht mehr ausreicht. Als Alternative bietet sich die Implementierung von entsprechend geeigneten Datenverarbeitungsschritten in Hardware auf einem qualifizierten SRAM-basierten FPGA an. Geeignete Bausteine sind jedoch empfindlich gegenüber der Strahlungsumgebung im Weltraum. Am Institut für Datentechnik und Kommunikationsnetze wurde eine fehlertolerante netzwerk-basierte Kommunikationsarchitektur entwickelt, die innerhalb eines geeigneten SRAM-basierten FPGAs Datenverarbeitungsmodule miteinander nach Bedarf zu Verarbeitungsketten verbindet, sowie den Austausch von einzelnen Modulen im Betrieb ermöglicht. Nicht oder nur partiell SEU mitigierte Module sollen bei strahlungsbedingten Fehlern im Modul durch das Protokoll und die Fehlererkennungsmechanismen der Kommunikationsarchitektur isoliert werden, um ein Ausbreiten des Fehlers im restlichen System-on-Chip zu verhindern. Im Kontext einer ESA Studie wurde diese Kommunikationsarchitektur um Komponenten erweitert und auf einer repräsentativen Hardwareplattform umgesetzt. Basierend auf den gesammelten Erfahrungen aus der Studie, wird in dieser Arbeit eine Analyse der tatsächlichen Fehlertoleranz-Eigenschaften sowie der Schwachstellen dieser ursprünglichen Implementierung durchgeführt. Die Kommunikationsarchitektur wurde an geeigneten Stellen um Fehlerdetektierungs- und Fehlerunterscheidungsmöglichkeiten erweitert, sowie um eine hardwarebasierte Überwachung ergänzt. Sowohl diese Maßnahmen, als auch die Erweiterung der Hardwareplattform um gezielte Fehlerinjektions-Möglichkeiten zum Emulieren von strahlungsinduzierten Fehlern in kritischen Komponenten eines nicht SEU mitigierten Prozessierungsmoduls werden genutzt, um die tatsächlichen auftretenden Effekte in der Kommunikationsarchitektur zu evaluieren. Anhand der Ergebnisse werden weitere Verbesserungsmaßnahmen speziell zur schnellen Detektierung und Isolation von fehlerhaften Knoten erarbeitet, selektiv implementiert und verifiziert. Insbesondere die Fähigkeit, fehlerhafte, nicht SEU mitigierte Netzwerkknoten innerhalb der Kommunikationsarchitektur zu isolieren, konnte dabei deutlich verbessert werden