ワイヤレス通信のための先進的な信号処理技術を用いた非線形補償法の研究

The inherit nonlinearity in analogue front-ends of transmitters and receivers have had primary impact on the overall performance of the wireless communication systems, as it gives arise of substantial distortion when transmitting and processing signals with such circuits. Therefore, the nonlinear compensation (linearization) techniques become essential to suppress the distortion to an acceptable extent in order to ensure sufficient low bit error rate. Furthermore, the increasing demands on higher data rate and ubiquitous interoperability between various multi-coverage protocols are two of the most important features of the contemporary communication system. The former demand pushes the communication system to use wider bandwidth and the latter one brings up severe coexistence problems. Having fully considered the problems raised above, the work in this Ph.D. thesis carries out extensive researches on the nonlinear compensations utilizing advanced digital signal processing techniques. The motivation behind this is to push more processing tasks to the digital domain, as it can potentially cut down the bill of materials (BOM) costs paid for the off-chip devices and reduce practical implementation difficulties. The work here is carried out using three approaches: numerical analysis & computer simulations; experimental tests using commercial instruments; actual implementation with FPGA. The primary contributions for this thesis are summarized as the following three points: 1) An adaptive digital predistortion (DPD) with fast convergence rate and low complexity for multi-carrier GSM system is presented. Albeit a legacy system, the GSM, however, has a very strict requirement on the out-of-band emission, thus it represents a much more difficult hurdle for DPD application. It is successfully implemented in an FPGA without using any other auxiliary processor. A simplified multiplier-free NLMS algorithm, especially suitable for FPGA implementation, for fast adapting the LUT is proposed. Many design methodologies and practical implementation issues are discussed in details. Experimental results have shown that the DPD performed robustly when it is involved in the multichannel transmitter. 2) The next generation system (5G) will unquestionably use wider bandwidth to support higher throughput, which poses stringent needs for using high-speed data converters. Herein the analog-to-digital converter (ADC) tends to be the most expensive single device in the whole transmitter/receiver systems. Therefore, conventional DPD utilizing high-speed ADC becomes unaffordable, especially for small base stations (micro, pico and femto). A digital predistortion technique utilizing spectral extrapolation is proposed in this thesis, wherein with band-limited feedback signal, the requirement on ADC speed can be significantly released. Experimental results have validated the feasibility of the proposed technique for coping with band-limited feedback signal. It has been shown that adequate linearization performance can be achieved even if the acquisition bandwidth is less than the original signal bandwidth. The experimental results obtained by using LTE-Advanced signal of 320 MHz bandwidth are quite satisfactory, and to the authors’ knowledge, this is the first high-performance wideband DPD ever been reported. 3) To address the predicament that mobile operators do not have enough contiguous usable bandwidth, carrier aggregation (CA) technique is developed and imported into 4G LTE-Advanced. This pushes the utilization of concurrent dual-band transmitter/receiver, which reduces the hardware expense by using a single front-end. Compensation techniques for the respective concurrent dual-band transmitter and receiver front-ends are proposed to combat the inter-band modulation distortion, and simultaneously reduce the distortion for the both lower-side band and upper-side band signals.電気通信大学201

Integrated Microwave Photonic Processors using Waveguide Mesh Cores

Integrated microwave photonics changes the scaling laws of information and communication systems offering architectural choices that combine photonics with electronics to optimize performance, power, footprint and cost. Application Specific Photonic Integrated Circuits, where particular circuits/chips are designed to optimally perform particular functionalities, require a considerable number of design and fabrication iterations leading to long-development times and costly implementations. A different approach inspired by electronic Field Programmable Gate Arrays is the programmable Microwave Photonic processor, where a common hardware implemented by the combination of microwave, photonic and electronic subsystems, realizes different functionalities through programming. Here, we propose the first-ever generic-purpose Microwave Photonic processor concept and architecture. This versatile processor requires a powerful end-to-end field-based analytical model to optimally configure all their subsystems as well as to evaluate their performance in terms of the radiofrequency gain, noise and dynamic range. Therefore, we develop a generic model for integrated Microwave Photonics systems. The key element of the processor is the reconfigurable optical core. It requires high flexibility and versatility to enable reconfigurable interconnections between subsystems as well as the synthesis of photonic integrated circuits. For this element, we focus on a 2-dimensional photonic waveguide mesh based on the interconnection of tunable couplers. Within the framework of this Thesis, we have proposed two novel interconnection schemes, aiming for a mesh design with a high level of versatility. Focusing on the hexagonal waveguide mesh, we explore the synthesis of a high variety of photonic integrated circuits and particular Microwave Photonics applications that can potentially be performed on a single hardware. In addition, we report the first-ever demonstration of such reconfigurable waveguide mesh in silicon. We demonstrate a world-record number of functionalities on a single photonic integrated circuit enabling over 30 different functionalities from the 100 that could be potentially obtained with a simple seven hexagonal cell structure. The resulting device can be applied to different fields including communications, chemical and biomedical sensing, signal processing, multiprocessor networks as well as quantum information systems. Our work is an important step towards this paradigm and sets the base for a new era of generic-purpose photonic integrated systems.Los dispositivos integrados de fotónica de microondas ofrecen soluciones optimizadas para los sistemas de información y comunicación. Generalmente, están compuestos por diferentes arquitecturas en las que subsistemas ópticos y electrónicos se integran para optimizar las prestaciones, el consumo, el tamaño y el coste del dispositivo final. Hasta ahora, los circuitos/chips de propósito específico se han diseñado para proporcionar una funcionalidad concreta, requiriendo así un número considerable de iteraciones entre las etapas de diseño, fabricación y medida, que origina tiempos de desarrollo largos y costes demasiado elevados. Una alternativa, inspirada por las FPGA (del inglés Field Programmable Gate Array), es el procesador fotónico programable. Este dispositivo combina la integración de subsistemas de microondas, ópticos y electrónicos para realizar, mediante la programación de los mismos y sus interconexiones, diferentes funcionalidades. En este trabajo, proponemos por primera vez el concepto del procesador de propósito general, así como su arquitectura. Además, con el fin de diseñar, optimizar y evaluar las prestaciones básicas del dispositivo, hemos desarrollado un modelo analítico extremo a extremo basado en las componentes del campo electromagnético. El modelo desarrollado proporciona como resultado la ganancia, el ruido y el rango dinámico global para distintas configuraciones de modulación y detección, en función de los subsistemas y su configuración. El elemento principal del procesador es su núcleo óptico reconfigurable. Éste requiere un alto grado de flexibilidad y versatilidad para reconfigurar las interconexiones entre los distintos subsistemas y para sintetizar los circuitos para el procesado óptico. Para este subsistema, proponemos el diseño de guías de onda reconfigurables para la creación de mallados bidimensionales. En el marco de esta tesis, hemos propuesto dos nuevos nodos de interconexión óptica para mallas reconfigurables, con el objetivo de obtener un mayor grado de versatilidad. Una vez escogida la malla hexagonal para el núcleo del procesador, hemos analizado la configuración de un gran número de circuitos fotónicos integrados y de funcionalidades de fotónica de microondas. El trabajo se ha completado con la demonstración de la primera malla reconfigurable integrada en un chip de silicio, demostrando además la síntesis de 30 de las 100 funcionalidades que potencialmente se pueden obtener con la malla diseñada compuesta de 7 celdas hexagonales. Este hecho supone un record frente a los sistemas de propósito específico. El sistema puede aplicarse en diferentes campos como las comunicaciones, los sensores químicos y biomédicos, el procesado de señales, la gestión y procesamiento de redes y los sistemas de información cuánticos. El conjunto del trabajo realizado representa un paso importante en la evolución de este paradigma, y sienta las bases para una nueva era de dispositivos fotónicos de propósito general.Els dispositius integrats de Fotònica de Microones oferixen solucions optimitzades per als sistemes d'informació i comunicació. Generalment, estan compostos per diferents arquitectures en què subsistemes òptics i electrònics s'integren per a optimitzar les prestacions, el consum, la grandària i el cost del dispositiu final. Fins ara, els circuits/xips de propòsit específic s'han dissenyat per a proporcionar una funcionalitat concreta, requerint així un nombre considerable d'iteracions entre les etapes de disseny, fabricació i mesura, que origina temps de desenrotllament llargs i costos massa elevats. Una alternativa, inspirada per les FPGA (de l'anglés Field Programmable Gate Array), és el processador fotònic programable. Este dispositiu combina la integració de subsistemes de microones, òptics i electrònics per a realitzar, per mitjà de la programació dels mateixos i les seues interconnexions, diferents funcionalitats. En este treball proposem per primera vegada el concepte del processador de propòsit general, així com la seua arquitectura. A més, a fi de dissenyar, optimitzar i avaluar les prestacions bàsiques del dispositiu, hem desenrotllat un model analític extrem a extrem basat en els components del camp electromagnètic. El model desenrotllat proporciona com resultat el guany, el soroll i el rang dinàmic global per a distintes configuracions de modulació i detecció, en funció dels subsistemes i la seua configuració. L'element principal del processador és el seu nucli òptic reconfigurable. Este requerix un alt grau de flexibilitat i versatilitat per a reconfigurar les interconnexions entre els distints subsistemes i per a sintetitzar els circuits per al processat òptic. Per a este subsistema, proposem el disseny de guies d'onda reconfigurables per a la creació de mallats bidimensionals. En el marc d'esta tesi, hem proposat dos nous nodes d'interconnexió òptica per a malles reconfigurables, amb l'objectiu d'obtindre un major grau de versatilitat. Una vegada triada la malla hexagonal per al nucli del processador, hem analitzat la configuració d'un gran nombre de circuits fotónicos integrats i de funcionalitats de fotónica de microones. El treball s'ha completat amb la demostració de la primera malla reconfigurable integrada en un xip de silici, demostrant a més la síntesi de 30 de les 100 funcionalitats que potencialment es poden obtindre amb la malla dissenyada composta de 7 cèl·lules hexagonals. Este fet suposa un rècord enfront dels sistemes de propòsit específic. El sistema pot aplicarse en diferents camps com les comunicacions, els sensors químics i biomèdics, el processat de senyals, la gestió i processament de xarxes i els sistemes d'informació quàntics. El conjunt del treball realitzat representa un pas important en l'evolució d'este paradigma, i assenta les bases per a una nova era de dispositius fotónicos de propòsit general.Pérez López, D. (2017). Integrated Microwave Photonic Processors using Waveguide Mesh Cores [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/91232TESI

Advanced signal processing techniques for the modeling and linearization of wireless communication systems.

Los nuevos estándares de comunicaciones digitales inalámbricas están impulsando el diseño de amplificadores de potencia con unas condiciones límites en términos de linealidad y eficiencia. Si bien estos nuevos sistemas exigen que los dispositivos activos trabajen cerca de la zona de saturación en busca de la eficiencia energética, la no linealidad inherente puede producir que el sistema muestre prestaciones inadecuadas en emisiones fuera de banda y distorsión en banda. La necesidad de técnicas digitales de compensación y la evolución en el diseño de nuevas arquitecturas de procesamiento de señales digitales posicionan a la predistorsión digital (DPD) como un enfoque práctico. Los predistorsionadores digitales se suelen basar en modelos de comportamiento como el memory polynomial (MP), el generalized memory polynomial (GMP) y el dynamic deviation reduction-based (DDR), etc. Los modelos de Volterra sufren la llamada "maldición de la dimensionalidad", ya que su complejidad tiende a crecer de forma exponencial a medida que el orden y la profundidad de memoria crecen. Esta tesis se centra principalmente en contribuir a la rama de conocimiento que enmarca el modelado y linealización de sistemas de comunicación inalámbrica. Los principales temas tratados son el modelo Volterra-Parafac y el modelo general de Volterra para sistemas complejos, los cuales tratan la estructura del DPD y las series de Volterra estructuradas con compressed-sensing y un método para la linealización en un rango de potencias de operación, que se centran en cómo los coeficientes de los modelos deben ser obtenidos.Premio Extraordinario de Doctorado U

Communication Subsystems for Emerging Wireless Technologies

The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels

Digital Signal Processing Techniques Applied to Radio over Fiber Systems

The dissertation aims to analyze different Radio over Fiber systems for the front-haul applications. Particularly, analog radio over fiber (A-RoF) are simplest and suffer from nonlinearities, therefore, mitigating such nonlinearities through digital predistortion are studied. In particular for the long haul A-RoF links, direct digital predistortion technique (DPDT) is proposed which can be applied to reduce the impairments of A-RoF systems due to the combined effects of frequency chirp of the laser source and chromatic dispersion of the optical channel. Then, indirect learning architecture (ILA) based structures namely memory polynomial (MP), generalized memory polynomial (GMP) and decomposed vector rotation (DVR) models are employed to perform adaptive digital predistortion with low complexities. Distributed feedback (DFB) laser and vertical capacity surface emitting lasers (VCSELs) in combination with single mode/multi-mode fibers have been linearized with different quadrature amplitude modulation (QAM) formats for single and multichannel cases. Finally, a feedback adaptive DPD compensation is proposed. Then, there is still a possibility to exploit the other realizations of RoF namely digital radio over fiber (D-RoF) system where signal is digitized and transmits the digitized bit streams via digital optical communication links. The proposed solution is robust and immune to nonlinearities up-to 70 km of link length. Lastly, in light of disadvantages coming from A-RoF and D-RoF, it is still possible to take only the advantages from both methods and implement a more recent form knows as Sigma Delta Radio over Fiber (S-DRoF) system. Second Order Sigma Delta Modulator and Multi-stAge-noise-SHaping (MASH) based Sigma Delta Modulator are proposed. The workbench has been evaluated for 20 MHz LTE signal with 256 QAM modulation. Finally, The 6x2 GSa/s sigma delta modulators are realized on FPGA to show a real time demonstration of S-DRoF system. The demonstration shows that S-DRoF is a competitive competitor for 5G sub-6GHz band applications

Active Transmitter Antenna Array Modeling for MIMO Applications

The rapid growth of data traffic in mobile communications has attracted interests to the Multiple-Input-Multiple-Output (MIMO) communication systems at millimeter-wave (mmWave) frequencies.\ua0 MIMO systems exploit active transmitter antenna arrays for higher energy efficiency and providing beamforming flexibility. The close integration of multiple PAs and antennas increases the transmitter analysis complexity. Moreover, due to the small antenna element spacing at mm-wave frequencies, isolators are too bulky and cannot be used. Therefore, including the effects of interactions between the antenna array and PAs is a significant aspect in the analysis of MIMO transmitters. For large active arrays, applying joint circuit and EM simulation tools for the analysis is a complicated and time-consuming task. In these occasions, behavioral models are the key to the fast and accurate evaluation of active transmitter antenna arrays.In this thesis, a technique for modeling the active transmitter antenna array performance is presented. The proposed model considers the effect of PAs nonlinearity as well as the coupling and mismatch in the antenna array. With this model, a comprehensive prediction of radiation pattern and signal distortions in the far-field is feasible. The model is experimentally verified by a mmWave active subarray antenna for a beam steering scenario and by performing over-the-air measurements. The measurement results effectively validate the modeling technique for a wide range of steering angles.\ua0\ua0 Furthermore, a linearity analysis is provided to predict transmitter performance in conjunction with beam-dependent digital predistortion (DPD) linearization. The study reveals the model potential in evaluating different DPD approaches as well as predicting the performance of linearized transmitters. The demonstration shows that the variation of nonlinear distortion versus steering angle depends significantly on the array configuration and beam direction.In summary, the proposed model allows for the prediction of the active transmitter antenna array performance in the early design stages with low computational effort. It can provide design guides for developing large-scale active arrays and can be employed for evaluating the DPD and transmitter linearity performance

Dynamic nonlinear behavioral modeling and adaptive predistortion for RF transmitters

Motivation -- Nonlinear dynamic behaviour, two-and three-box models -- Objectives and outline of the thesis -- Two-Box models, de-embedding nonlinearities and dynamic memory effects -- Transmitter prototype -- Hammerstein and Wiener model construction -- Three-box oriented nonlinear model -- Three-box model's two-stage identification procedure -- Adaptive predistortion construction using single tone signal -- Hypothetical model and adaptive predistortion -- Construction of the complete predistorted system with a two-box model -- Complete predistorted system and linearization validation with CDMA signal