Nonlinearity and noise modeling of operational transconductance amplifiers for continuous time analog filters

A general framework for performance optimization of continuous-time OTA-C (Operational Transconductance Amplifier-Capacitor) filters is proposed. Efficient procedures for evaluating nonlinear distortion and noise valid for any filter of arbitrary order are developed based on the matrix description of a general OTA-C filter model . Since these procedures use OTA macromodels, they can be used to obtain the results significantly faster than transistor-level simulation. In the case of transient analysis, the speed-up may be as much as three orders of magnitude without almost no loss of accuracy. This makes it possible to carry out direct numerical optimization of OTA-C filters with respect to important characteristics such as noise performance, THD, IM3, DR or SNR. On the other hand, the general OTA-C filter model allows us to apply matrix transforms that manipulate (rescale) filter element values and/or change topology without changing its transfer function. The above features are a basis to build automated optimization procedures for OTA-C filters. In particular, a systematic optimization procedure using equivalence transformations is proposed. The research also proposes suitable software implementations of the optimization process. The first part of the research proposes a general performance optimization procedure and to verify the process two application type examples are mentioned. An application example of the proposed approach to optimal block sequencing and gain distribution of 8th order cascade Butterworth filter (for two variants of OTA topologies) is given. Secondly the modeling tool is used to select the best suitable topology for a 5th order Bessel Low Pass Filter. Theoretical results are verified by comparing to transistor-level simulation withCADENCE. For the purpose of verification, the filters have also been fabricated in standard 0.5mm CMOS process. The second part of the research proposes a new linearization technique to improve the linearity of an OTA using an Active Error Feedforward technique. Most present day applications require very high linear circuits combined with low noise and low power consumption. An OTA based biquad filter has also been fabricated in 0.35mm CMOS process. The measurement results for the filter and the stand alone OTA have been discussed. The research focuses on these issues

The design of active resistors and transductors in a CMOS technology

Merged with duplicate record 10026.1/2618 on 07.20.2017 by CS (TIS)This thesis surveys linearisation techniques for implementing monolithic MOS active resistors and transconductors, and investigates the design of linear tunable resistors and transconductors. Improving linearity and tunability in the presence of non-ideal factors such as bulk modulation, mobility-degradation effects and mismatch of transistors is a principal objective. A family of new non-saturation-mode resistors and two novel saturation-mode transconductors are developed. Where possible, approximate analytical expressions are derived to explain the principles of operation. Performance comparisons of the new structures are made with other well-known circuits and their relative advantages and disadvantages evaluated. Experimental and simulation results are presented which validate the proposed linearisation techniques. It is shown that the proposed family of resistors offers improved linearity whilst the transconductors combine extended tunability with low distortion. Continuous-time filter examples are given to demonstrate the potential of these circuits for application in analogue signal-processing tasks.GEC Plessey Semiconductors, Plymout

Low Power Filtering Techniques for Wideband and Wireless Applications

This dissertation presents design and implementation of continuous time analog filters for two specific applications: wideband analog systems such as disk drive channel and low-power wireless applications. Specific focus has been techniques that reduce the power requirements of the overall system either through improvement in architecture or efficiency of the analog building blocks. The first problem that this dissertation addresses is the implementation of wideband filters with high equalization gain. An efficient architecture that realizes equalization zeros by combining available transfer functions associated with a biquadratic cell is proposed. A 330MHz, 5th order Gm-C lowpass Butterworth filter with 24dB boost is designed using the proposed architecture. The prototype fabricated in standard 0.35um CMOS process shows -41dB of IM3 for 250mV peak to peak swing with 8.6mW/pole of power dissipation. Also, an LC prototype implemented using similar architecture is discussed in brief. It is shown that, for practical range of frequency and SNR, LC based design is more power efficient than a Gm-C one, though at the cost of much larger area. Secondly, a complementary current mirror based building block is proposed, which pushes the limits imposed by conventional transconductors on the powerefficiency of Gm-C filters. Signal processing through complementary devices provides good linearity and Gm/Id efficiency and is shown to improve power efficiency by nearly 7 times. A current-mode 4th order Butterworth filter is designed, in 0.13um UMC technology, using the proposed building. It provides 54.2dB IM3 and 55dB SNR in 1.3GHz bandwidth while consuming as low as 24mW of power. All CMOS filter realization occupies a relatively small area and is well suited for integration in deep submicron technologies. Thirdly, a 20MHz, 68dB dynamic range active RC filter is presented. This filter is designed for a ten bit continuous time sigma delta ADC architecture developed specifically for fine-line CMOS technologies. Inverter based amplification and a common mode feedback for such amplifiers are discussed. The filter consumes 5mW of power and occupies an area of 0.07 mm2

Architectures and Circuit Techniques for High-Performance Field-Programmable CMOS Software Defined Radios

Next-generation wireless communication systems put more stringent performance requirements on the wireless RF receiver circuits. Sensitivity, linearity, bandwidth and power consumption are some of the most important specifications that often face tightly coupled tradeoffs between them. To increase the data throughput, a large number of fragmented spectrums are being introduced to the wireless communication standards. Carrier aggregation technology needs concurrent communication across several non-contiguous frequency bands, which results in a rapidly growing number of band combinations. Supporting all the frequency bands and their aggregation combinations increases the complexity of the RF receivers. Highly flexible software defined radio (SDR) is a promising technology to address these applications scenarios with lower complexity by relaxing the specifications of the RF filters or eliminating them. However, there are still many technology challenges with both the receiver architecture and the circuit implementations. The performance requirements of the receivers can also vary across different application scenario and RF environments. Field-programmable dynamic performance tradeoff can potentially reduce the power consumption of the receiver. In this dissertation, we address the performance enhancement challenges in the wideband SDRs by innovations at both the circuit building block level and the receiver architecture level. A series of research projects are conducted to push the state-of-the-art performance envelope and add features such as field-programmable performance tradeoff and concurrent reception. The projects originate from the concept of thermal noise canceling techniques and further enhance the RF performance and add features for more capable SDR receivers. Four generations of prototype LNA or receiver chips are designed, and each of them pushes at least one aspect of the RF performance such as bandwidth, linearity, and NF. A noise-canceling distributed LNA breaks the tradeoff between NF and RF bandwidth by introducing microwave circuit techniques from the distributed amplifiers. The LNA architecture uniquely provides ultra high bandwidth and low NF at low frequencies. A family of field-programmable LNA realized field-programmable performance tradeoff with current-reuse programmable transconductance cells. Interferer-reflecting loops can be applied around the LNAs to improve their input linearity by rejecting the out-of-band interferers with a wideband low in- put impedance. A low noise transconductance amplifier (LNTA) that operates in class-AB-C is invented to can handle rail-to-rail out-of-band blocker without saturation. Class-AB and class-C transconductors form a composite amplifier to increase the linear range of the input voltage. A new antenna interface named frequency-translational quadrature-hybrid (FTQH) breaks the input impedance matching requirement of the LNAs by introducing quadrature hybrid couplers to the CMOS RFIC design. The FTQH receiver achieves wideband sub-1dB NF and supports scalable massive frequency-agile concurrent reception

A Q-enhanced 3.6 GHz tunable CMOS bandpass filter for wideband wireless applications

With the rapid development of information technology, more and more bandwidth is required to transmit multimedia data. Since local communication networks are moving to wireless domain, it brings up great challenges for making integrated wideband wireless front-ends suitable for these applications. RF filtering is a fundamental need in all wireless front-ends and is one of the most difficult parts to be integrated. This has been a major obstacle to the implementation of low power and low cost integrated wireless terminals. Lots of previous work has been done to make integrated RF filters applicable to these applications. However, some of these filters are not designed with standard CMOS technology. Some of them are not designed in desired frequency bands and others do not have sufficient frequency bandwidth. This research demonstrates the design of a tunable wideband RF filter that operates at 3.6 GHz and can be easily changed to a higher frequency range up to 5 GHz. This filter is superior to the previous designs in the following aspects: a) wider bandwidth, b) easier to tune, c) balancing in noise and linearity, and d) using standard CMOS technology. The design employs the state-of-the-art inductor degenerated LNA, acting as a transconductor to minimize the overall noise figure. A Q-enhancement circuit is employed to compensate the loss from lossy on-chip spiral inductors. Center frequency and bandwidth tuning circuits are also embedded to make the filter suitable for multi band operations. At first, a second order bandpass filter prototype was designed in the standard 0.18 ìm CMOS process. Simulation results showed that at 3.6 GHz center frequency and with a 60-MHz bandwidth, the input third-order intermodulation product (IIP3) and input-referred 1 dB compression point (P1dB) was -22.5 dBm and -30.5 dBm respectively. The image rejection at 500 MHz away from the center frequency was 32 dB (250 MHz intermediate frequency). The Q of the filter was tunable over 3000 and the center frequency tuning range was about 150 MHz. By cascading three stages of second order filters, a sixth order filter was designed to enhance the image rejection ability and to extend the filter bandwidth. The sixth order filter had been fabricated in the standard 0.18 ìm CMOS process using 1.8-V supply. The chip occupies only 0.9 mm 0.9 mm silicon area and has a power consumption of 130-mW. The measured center frequency was tunable from 3.54 GHz to 3.88 GHz, bandwidth was tunable from 35 MHz to 80 MHz. With a 65 MHz bandwidth, the filter had a gain of 13 dB, an IIP3 of -29 dBm and a P1dB of -46 dBm

A wide dynamic range high-q high-frequency bandpass filter with an automatic quality factor tuning scheme

An 80 MHz bandpass filter with a tunable quality factor of 16∼44 using an improved transconductor circuit is presented. A noise optimized biquad structure for high-Q, high- frequency bandpass filter is proposed. The quality factor of the filter is tuned using a new quality factor locked loop algorithm. It was shown that a second-order quality factor locked loop is necessary and sufficient to tune the quality factor of a bandpass filter with zero steady state error. The accuracy, mismatch, and sensitivty analysis of the new tuning scheme was performed and analyzed. Based on the proposed noise optimized filter structure and new quality factor tuning scheme, a biquad filter was designed and fabricated in 0.25 μm BiCMOS process. The measured results show that the biquad filter achieves a SNR of 45 dB at IMD of 40 dB. The P-1dB compression point and IIP3 of the filter are -10 dBm and -2.68 dBm, respectively. The proposed biquad filter and quality factor tuning scheme consumes 58mW and 13 mW of power at 3.3 V supply.Ph.D.Committee Chair: Allen Phillip; Committee Member: Hasler Paul; Committee Member: Keezer David; Committee Member: Kenny James; Committee Member: Pan Ronghu

Design of RF/IF analog to digital converters for software radio communication receivers

Software radio architecture can support multiple standards by performing analogto- digital (A/D) conversion of the radio frequency (RF) signals and running reconfigurable software programs on the backend digital signal processor (DSP). A slight variation of this architecture is the software defined radio architecture in which the A/D conversion is performed on intermediate frequency (IF) signals after a single down conversion. The first part of this research deals with the design and implementation of a fourth order continuous time bandpass sigma-delta (CT BP) C based on LC filters for direct RF digitization at 950 MHz with a clock frequency of 3.8 GHz. A new ADC architecture is proposed which uses only non-return to zero feedback digital to analog converter pulses to mitigate problems associated with clock jitter. The architecture also has full control over tuning of the coefficients of the noise transfer function for obtaining the best signal to noise ratio (SNR) performance. The operation of the architecture is examined in detail and extra design parameters are introduced to ensure robust operation of the ADC. Measurement results of the ADC, implemented in IBM 0.25 µm SiGe BiCMOS technology, show SNR of 63 dB and 59 dB in signal bandwidths of 200 kHz and 1 MHz, respectively, around 950 MHz while consuming 75 mW of power from ± 1.25 V supply. The second part of this research deals with the design of a fourth order CT BP ADC based on gm-C integrators with an automatic digital tuning scheme for IF digitization at 125 MHz and a clock frequency of 500 MHz. A linearized CMOS OTA architecture combines both cross coupling and source degeneration in order to obtain good IM3 performance. A system level digital tuning scheme is proposed to tune the ADC performance over process, voltage and temperature variations. The output bit stream of the ADC is captured using an external DSP, where a software tuning algorithm tunes the ADC parameters for best SNR performance. The IF ADC was designed in TSMC 0.35 µm CMOS technology and it consumes 152 mW of power from ± 1.65 V supply

Design of a 125 mhz tunable continuous-time bandpass modulator for wireless IF applications

Bandpass sigma-delta modulators combine oversampling and noise shaping to get very high resolution in a limited bandwidth. They are widely used in applications that require narrowband high-resolution conversion at high frequencies. In recent years interests have been seen in wireless system and software radio using sigma-delta modulators to digitize signals near the front end of radio receivers. Such applications necessitate clocking the modulators at a high frequency (MHz or above). Therefore a loop filter is required in continuous-time circuits (e.g., using transconductors and integrators) rather than discretetime circuits (e.g., using switched capacitors) where the maximum clocking rate is limited by the bandwidth of Opamp, switchÂs speed and settling-time of the circuitry. In this work, the design of a CMOS fourth-order bandpass sigma-delta modulator clocking at 500 MHz for direct conversion of narrowband signals at 125 MHz is presented. A new calibration scheme is proposed for the best signal-to-noise-distortion-ratio (SNDR) of the modulator. The continuous-time loop filter is based on Gm-C resonators. A novel transconductance amplifier has been developed with high linearity at high frequency. Qfactor of filter is enhanced by tunable negative impedance which cancels the finite output impendence of OTA. The fourth-order modulator is implemented using 0.35 mm triplemetal standard analog CMOS technology. Postlayout simulation in CADENCE demonstrates that the modulator achieves a SNDR of 50 dB (~8 bit) performance over a 1 MHz bandwidth. The modulatorÂs power consumption is 302 mW from supply power of ± 1.65V

Continuous-time low-pass filters for integrated wideband radio receivers

This thesis concentrates on the design and implementation of analog baseband continuous-time low-pass filters for integrated wideband radio receivers. A total of five experimental analog baseband low-pass filter circuits were designed and implemented as a part of five single-chip radio receivers in this work. After the motivation for the research work presented in this thesis has been introduced, an overview of analog baseband filters in radio receivers is given first. In addition, a review of the three receiver architectures and the three wireless applications that are adopted in the experimental work of this thesis is presented. The relationship between the integrator non-idealities and integrator Q-factor, as well as the effect of the integrator Q-factor on the filter frequency response, are thoroughly studied on the basis of a literature review. The theoretical study that is provided is essential for the gm-C filter synthesis with non-ideal lossy integrators that is presented after the introduction of different techniques to realize integrator-based continuous-time low-pass filters. The filter design approach proposed for gm-C filters is original work and one of the main points in this thesis, in addition to the experimental IC implementations. Two evolution versions of fourth-order 10-MHz opamp-RC low-pass filters designed and implemented for two multicarrier WCDMA base-station receivers in a 0.25-µm SiGe BiCMOS technology are presented, along with the experimental results of both the low-pass filters and the corresponding radio receivers. The circuit techniques that were used in the three gm-C filter implementations of this work are described and a common-mode induced even-order distortion in a pseudo-differential filter is analyzed. Two evolution versions of fifth-order 240-MHz gm-C low-pass filters that were designed and implemented for two single-chip WiMedia UWB direct-conversion receivers in a standard 0.13-µm and 65-nm CMOS technology, respectively, are presented, along with the experimental results of both the low-pass filters and the second receiver version. The second UWB filter design was also embedded with an ADC into the baseband of a 60-GHz 65-nm CMOS radio receiver. In addition, a third-order 1-GHz gm-C low-pass filter was designed, rather as a test structure, for the same receiver. The experimental results of the receiver and the third gm-C filter implementation are presented