Accelerating Electromigration Aging: Fast Failure Detection for Nanometer ICs

For practical testing and detection of electromigration (EM) induced failures in dual damascene copper interconnects, one critical issue is creating stressing conditions to induce the chip to fail exclusively under EM in a very short period of time so that EM sign-off and validation can be carried out efficiently. Existing acceleration techniques, which rely on increasing temperature and current densities beyond the known limits, also accelerate other reliability effects making it very difficult, if not impossible, to test EM in isolation. In this article, we propose novel EM wear-out acceleration techniques to address the aforementioned issue. First we show that multi-segment interconnects with reservoir and sink structures can be exploited to significantly speedup the EM wear-out process. Based on this observation, we propose three strategies to accelerate EM induced failure: reservoir-enhanced acceleration, sink-enhanced acceleration, and a hybrid method that combines both reservoir and sink structures. We then propose several configurable interconnect structures that exploit atomic reservoirs and sinks for accelerated EM testing. Such configurable interconnect structures are very flexible and can be used to achieve significant lifetime reductions at the cost of some routing resources. Using the proposed technique, EM testing can be carried out at nominal current densities, and at a much lower temperature compared to traditional testing methods. This is the most significant contribution of this work since, to our knowledge, this is the only method that allows EM testing to be performed in a controlled environment without the risk of invoking other reliability effects that are also accelerated by elevated temperature and current density. Simulation results show that, using the proposed method, we can reduce the EM lifetime of a chip from 10 years down to a few hours 10^5X acceleration under the 150C temperature limit, which is sufficient for practical EM testing of typical nanometer CMOS ICs

An Integrated Subharmonic Coupled-Oscillator Scheme for a 60-GHz Phased-Array Transmitter

This paper describes the design of an integrated coupled-oscillator array in SiGe for millimeter-wave applications. The design focuses on a scalable radio architecture where multiple dies are tiled to form larger arrays. A 2 × 2 oscillator array for a 60-GHz transmitter is fabricated with integrated power amplifiers and on-chip antennas. To lock between multiple dies, an injection-locking scheme appropriate for wire-bond interconnects is described. The 2 × 2 array demonstrates a 200–MHz locking range and 1 × 4 array formed by two adjacent chips has a 60-MHz locking range. The phase noise of the coupled oscillators is below 100 dBc/Hz at a 1-MHz offset when locked to an external reference. To the best of the authors’ knowledge, this is the highest frequency demonstration of coupled oscillators fabricated in a conventional silicon integrated-circuit process

Devices Having Compliant Wafer-level Input/output Interconnections And Packages Using Pillars And Methods Of Fabrication Thereof

Devices having one or more of the following: an input/output (I/O) interconnect system, an optical I/O interconnect, an electrical I/O interconnect, a radio frequency I/O interconnect, are disclosed. A representative I/O interconnect system includes a first substrate and a second substrate. The first substrate includes a compliant pillar vertically extending from the first substrate. The compliant pillar is constructed of a first material. The second substrate includes a compliant socket adapted to receive the compliant pillar. The compliant socket is constructed of a second material.Georgia Tech Research Corporatio

Photonic integration enabling new multiplexing concepts in optical board-to-board and rack-to-rack interconnects

New broadband applications are causing the datacenters to proliferate, raising the bar for higher interconnection speeds. So far, optical board-to-board and rack-to-rack interconnects relied primarily on low-cost commodity optical components assembled in a single package. Although this concept proved successful in the first generations of optical-interconnect modules, scalability is a daunting issue as signaling rates extend beyond 25 Gb/s. In this paper we present our work towards the development of two technology platforms for migration beyond Infiniband enhanced data rate (EDR), introducing new concepts in board-to-board and rack-to-rack interconnects. The first platform is developed in the framework of MIRAGE European project and relies on proven VCSEL technology, exploiting the inherent cost, yield, reliability and power consumption advantages of VCSELs. Wavelength multiplexing, PAM-4 modulation and multi-core fiber (MCF) multiplexing are introduced by combining VCSELs with integrated Si and glass photonics as well as BiCMOS electronics. An in-plane MCF-to-SOI interface is demonstrated, allowing coupling from the MCF cores to 340x400 nm Si waveguides. Development of a low-power VCSEL driver with integrated feed-forward equalizer is reported, allowing PAM-4 modulation of a bandwidth-limited VCSEL beyond 25 Gbaud. The second platform, developed within the frames of the European project PHOXTROT, considers the use of modulation formats of increased complexity in the context of optical interconnects. Powered by the evolution of DSP technology and towards an integration path between inter and intra datacenter traffic, this platform investigates optical interconnection system concepts capable to support 16QAM 40GBd data traffic, exploiting the advancements of silicon and polymer technologies

Two Hardware Implementations of the Exhaustive Synthetic AER Generation Method

Address-Event-Representation (AER) is a communications protocol for transferring images between chips, originally developed for bio-inspired image processing systems. In [6], [5] various software methods for synthetic AER generation were presented. But in neuro-inspired research field, hardware methods are needed to generate AER from laptop computers. In this paper two real time implementations of the exhaustive method, proposed in [6], [5], are presented. These implementations can transmit, through AER bus, images stored in a computer using USB-AER board developed by our RTCAR group for the CAVIAR EU project.Commission of the European Communities IST-2001-34124 (CAVIAR)Comisión Interministerial de Ciencia y Tecnología TIC-2003-08164-C03-0

On-Line Dependability Enhancement of Multiprocessor SoCs by Resource Management

This paper describes a new approach towards dependable design of homogeneous multi-processor SoCs in an example satellite-navigation application. First, the NoC dependability is functionally verified via embedded software. Then the Xentium processor tiles are periodically verified via on-line self-testing techniques, by using a new IIP Dependability Manager. Based on the Dependability Manager results, faulty tiles are electronically excluded and replaced by fault-free spare tiles via on-line resource management. This integrated approach enables fast electronic fault detection/diagnosis and repair, and hence a high system availability. The dependability application runs in parallel with the actual application, resulting in a very dependable system. All parts have been verified by simulation