Compiler optimization and ordering effects on VLIW code compression

Code size has always been an important issue for all embedded applications as well as larger systems. Code compression techniques have been devised as a way of battling bloated code; however, the impact of VLIW compiler methods and outputs on these compression schemes has not been thoroughly investigated. This paper describes the application of single- and multipleinstruction dictionary methods for code compression to decrease overall code size for the TI TMS320C6xxx DSP family. The compression scheme is applied to benchmarks taken from the Mediabench benchmark suite built with differing compiler optimization parameters. In the single instruction encoding scheme, it was found that compression ratios were not a useful indicator of the best overall code size – the best results (smallest overall code size) were obtained when the compression scheme was applied to sizeoptimized code. In the multiple instruction encoding scheme, changing parallel instruction order was found to only slightly improve compression in unoptimized code and does not affect the code compression when it is applied to builds already optimized for size

Gbit/second lossless data compression hardware

This thesis investigates how to improve the performance of lossless data compression hardware as a tool to reduce the cost per bit stored in a computer system or transmitted over a communication network. Lossless data compression allows the exact reconstruction of the original data after decompression. Its deployment in some high-bandwidth applications has been hampered due to performance limitations in the compressing hardware that needs to match the performance of the original system to avoid becoming a bottleneck. Advancing the area of lossless data compression hardware, hence, offers a valid motivation with the potential of doubling the performance of the system that incorporates it with minimum investment. This work starts by presenting an analysis of current compression methods with the objective of identifying the factors that limit performance and also the factors that increase it. [Continues.

SEPARATING INSTRUCTION FETCHES FROM MEMORY ACCESSES : ILAR (INSTRUCTION LINE ASSOCIATIVE REGISTERS)

Due to the growing mismatch between processor performance and memory latency, many dynamic mechanisms which are “invisible” to the user have been proposed: for example, trace caches and automatic pre-fetch units. However, these dynamic mechanisms have become inadequate due to implicit memory accesses that have become so expensive. On the other hand, compiler-visible mechanisms like SWAR (SIMD Within A Register) and LARs (Line Associative Registers) are potentially more effective at improving data access performance. This thesis investigates applying the same ideas to improve instruction access. ILAR (Instruction LARs) store instructions in wide registers. Instruction blocks are explicitly loaded into ILAR, using block compression to enhance memory bandwidth. The control flow of the program then refers to instructions directly by their position within an ILAR, rather than by lengthy memory addresses. Because instructions are accessed directly from within registers, there is no implicit instruction fetch from memory. This thesis proposes an instruction set architecture for ILAR, investigates a mechanism to load ILAR using the best available block compression algorithm and also develop hardware descriptions for both ILAR and a conventional memory cache model so that performance comparisons could be made on the instruction fetch stage

Adaptive and Flexible Dictionary Code Compression for Embedded Applications

ABSTRACT Dictionary code compression is a technique where long instructions in the memory are replaced with shorter code words used as index in a table to look up the original instructions. We present a new view of dictionary code compression for moderately high-performance processors for embedded applications. Previous work with dictionary code compression has shown decent performance and energy savings results which we verify with our own measurement that are more thorough than previously published. We also augment previous work with a more thorough analysis on the effects of cache and line size changes. In addition, we introduce the concept of aggregated profiling to allow for two or more programs to share the same dictionary contents. Finally, we also introduce dynamic dictionaries where the dictionary contents is considered to be part of the context of a process and show that the performance overhead of reloading the dictionary contents on a context switch is negligible while on the same time we can save considerable energy with a more specialized dictionary contents

Trends in hardware architecture for mobile devices

In the last ten years, two main factors have fueled the steady growth in sales of mobile computing and communication devices: a) the reduction of the footprint of the devices themselves, such as cellular handsets and small computers; and b) the success in developing low-power hardware which allows the devices to operate autonomously for hours or even days. In this review, I show that the first generation of mobile devices was DSP centric – that is, its architecture was based in fast processing of digitized signals using low- power, yet numerically powerful DSPs. However, the next generation of mobile devices will be built around DSPs and low power microprocessor cores for general processing applications. Mobile devices will become data-centric. The main challenge for designers of such hybrid architectures is to increase the computational performance of the computing unit, while keeping power constant, or even reducing it. This report shows that low-power mobile hardware architectures design goes hand in hand with advances in compiling techniques. We look at the synergy between hardware and software, and show that a good balance between both can lead to innovative lowpower processor architectures