A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

The Design, Testing, and Analysis of a Constant Jammer for the Bluetooth Low Energy (BLE) Wireless Communication Protocol

The decreasing cost of web-enabled smart devices utilizing embedded processors, sensors, and wireless communication hardware have created an optimal ecosystem for the Internet of Things (IoT). IEEE802.15.4, IEEE802.11ah, WirelessHART, ZigBee Smart Energy, Bluetooth (BT), and Bluetooth Low Energy (BLE) are amongst the most commonly used wireless standards for IoT systems. Each of these standards has tradeoffs concerning power consumption, range of communication, network formation, security, reliability, and ease of implementation. The most widely used standards for IoT are Bluetooth, BLE, and Zigbee. This paper discusses the vulnerabilities in the implementation of the PHY and link layers of BLE. The link layer defines the scheme for establishing a link between two devices. Scanning devices are able to establish communication with other devices that are sending advertising packets. These advertising packets are sent out in a deterministic fashion. The advertising channels for BLE, specified by the PHY layer, are Channels 37, 38, and 39, at center frequencies 2.402, 2.426, and 2.480 GHz, respectively. This scheme for establishing a connection seems to introduce an unintentional gap in the security of the protocol. Creating and transmitting tones with center frequencies corresponding to those of the advertising channels, a victim BLE device will be unable to establish a connection with another BLE device. Jamming a mesh network of BLE devices relies on this same concept. The proposed jamming system is an inexpensive one which utilizes the following hardware. Three individual synthesizers, a microcontroller (MCU), Wilkinson power combiner, power amplifier, and antenna, integrated on a single PCB, are used to transmit a 3-tone signal. Due to the unprecedented nature of the COVID-19 pandemic, necessary adjustments were made to the jammer system design. In the first modified jamming scheme, a single synthesizer evaluation board, power amplifier, and antenna, are used to transmit jamming tones in the form of a frequency hop. Limitations of the frequency hop approach necessitated a second modified scheme. In this second scheme a synthesizer and two Software Defined Radios (SDR), connected to a personal computer, continuously generate three individual jamming tones. The proposed jammer and the modified ones all classify as constant jammers as the transmission of jamming signals is continuous. Both modified jamming schemes are tested. The results of jamming using the second modified scheme validate the objective of simultaneous jamming of the advertising channels of BLE devices. The success of the modified scheme enables the original goal of creating a relatively inexpensive custom PCB for BLE advertising channel jamming. By exploiting the weakness of the BLE protocol, the hope is to have the governing body for Bluetooth, Bluetooth Special Interest Group (SIG), improve security for the future releases of BLE

The Design, Building, and Testing of a Constant on Discreet Jammer for the Ieee 802.15.4/ZIGBEE Wireless Communication Protocol

As wireless protocols become easier to implement, more products come with wireless connectivity. This latest push for wireless connectivity has left a gap in the development of the security and the reliability of some protocols. These wireless protocols can be used in the growing field of IoT where wireless sensors are used to share information throughout a network. IoT is being implemented in homes, agriculture, manufactory, and in the medical field. Disrupting a wireless device from proper communication could potentially result in production loss, security issues, and bodily harm. The 802.15.4/ZigBee protocol is used in low power, low data rate, and low cost wireless applications such as medical devices and home automation devices. This protocol uses CSMA-CA (Carrier Sense Multiple Access w/ Collision Avoidance) which allows for multiple ZigBee devices to transmit simultaneousness and allows for wireless coexistence with the existing protocols at the same frequency band. The CSMA-CA MAC layer seems to introduce an unintentional gap in the reliability of the protocol. By creating a 16-tone signal with center frequencies located in the center of the multiple access channels, all channels will appear to be in use and the ZigBee device will be unable to transmit data. The jamming device will be created using the following hardware implementation. An FPGA connected to a high-speed Digital to Analog Converter will be used to create a digital signal synthesizer device that will create the 16-tone signal. The 16-tone signal will then be mixed up to the 2.4 GHz band, amplified, and radiated using a 2.4 GHz up-converter device. The transmitted jamming signal will cause the ZigBee MAC layer to wait indefinitely for the channel to clear. Since the channel will not clear, the MAC layer will not allow any transmission and the ZigBee devices will not communicate

A Comprehensive Survey on Networking over TV White Spaces

The 2008 Federal Communication Commission (FCC) ruling in the United States opened up new opportunities for unlicensed operation in the TV white space spectrum. Networking protocols over the TV white spaces promise to subdue the shortcomings of existing short-range multi-hop wireless architectures and protocols by offering more availability, wider bandwidth, and longer-range communication. The TV white space protocols are the enabling technologies for sensing and monitoring, Internet-of-Things (IoT), wireless broadband access, real-time, smart and connected community, and smart utility applications. In this paper, we perform a retrospective review of the protocols that have been built over the last decade and also the new challenges and the directions for future work. To the best of our knowledge, this is the first comprehensive survey to present and compare existing networking protocols over the TV white spaces.Comment: 19 page

Transmission Experiment of Bandwidth Compressed Carrier Aggregation in a Realistic Fading Channel

In this paper, an experimental testbed is designed to evaluate the performance of a bandwidth compressed multicarrier technique termed spectrally efficient frequency division multiplexing (SEFDM) in a carrier aggregation (CA) scenario1. Unlike orthogonal frequency division multiplexing (OFDM), SEFDM is a non-orthogonal waveform which, relative to OFDM, packs more sub-carriers in a given bandwidth, thereby improving spectral efficiency. CA is a long term evolution-advanced (LTE-Advanced) featured technique that offers a higher throughput by aggregating multiple legacy radio bands. Considering the scarcity of radio spectrum, SEFDM signals can be utilized to enhance CA performance. The combination of the two techniques results in a larger number of aggregated component carriers (CCs) and therefore increased data rate in a given bandwidth with no additional spectral allocation. It is experimentally shown that CA-SEFDM can aggregate up to 7 CCs in a limited bandwidth while CA-OFDM can only put 5 CCs in the same bandwidth. In this work, LTE-like framed CA-SEFDM signals are generated and delivered through a realistic LTE channel. A complete experimental setup is described together with error performance and effective spectral efficiency comparisons. Experimental results show that the measured BER performance for CA-SEFDM is very close to CA-OFDM and the effective spectral efficiency of CA-SEFDM can be substantially higher than that of CA-OFDM

Investigation of RF Direct Detection Architecture Circuits for Metamaterial Sensor Applications

Recent advances in metamaterials research has enabled the development of highly sensitive near-field microwave sensors with unprecedented sensitivity. In this work, we take advantage of the increase in the sensitivity to produce a compact, lightweight, affordable, and accurate measurement system for the applications of microwave imaging and material characterization. This sensitivity enhancement due to the inclusion of metamaterials opens the door for the use of inexpensive microwave components and circuits such as direct detectors while leveraging the high sensitivity of the metamaterial probe to deliver an overall accurate measurement system comparable to that of a traditional probe used in conjunction with a vector network analyzer. The sensor developed is composed of a metamaterial sensor with an RF direct detection circuit. In this work, two prototype measurement systems have been designed and tested. Measurement of small cracks in conductors and material characterization using the proposed system were performed. The results from the newly developed sensors were compared with the results from vector network analyzer measurements. Good agreement was obtained. The feasibility of a compact, lightweight, affordable, and accurate system has been demonstrated by using the developed prototypes

Recent Trends in Communication Networks

In recent years there has been many developments in communication technology. This has greatly enhanced the computing power of small handheld resource-constrained mobile devices. Different generations of communication technology have evolved. This had led to new research for communication of large volumes of data in different transmission media and the design of different communication protocols. Another direction of research concerns the secure and error-free communication between the sender and receiver despite the risk of the presence of an eavesdropper. For the communication requirement of a huge amount of multimedia streaming data, a lot of research has been carried out in the design of proper overlay networks. The book addresses new research techniques that have evolved to handle these challenges

Co-design of Security Aware Power System Distribution Architecture as Cyber Physical System

The modern smart grid would involve deep integration between measurement nodes, communication systems, artificial intelligence, power electronics and distributed resources. On one hand, this type of integration can dramatically improve the grid performance and efficiency, but on the other, it can also introduce new types of vulnerabilities to the grid. To obtain the best performance, while minimizing the risk of vulnerabilities, the physical power system must be designed as a security aware system. In this dissertation, an interoperability and communication framework for microgrid control and Cyber Physical system enhancements is designed and implemented taking into account cyber and physical security aspects. The proposed data-centric interoperability layer provides a common data bus and a resilient control network for seamless integration of distributed energy resources. In addition, a synchronized measurement network and advanced metering infrastructure were developed to provide real-time monitoring for active distribution networks. A hybrid hardware/software testbed environment was developed to represent the smart grid as a cyber-physical system through hardware and software in the loop simulation methods. In addition it provides a flexible interface for remote integration and experimentation of attack scenarios. The work in this dissertation utilizes communication technologies to enhance the performance of the DC microgrids and distribution networks by extending the application of the GPS synchronization to the DC Networks. GPS synchronization allows the operation of distributed DC-DC converters as an interleaved converters system. Along with the GPS synchronization, carrier extraction synchronization technique was developed to improve the system’s security and reliability in the case of GPS signal spoofing or jamming. To improve the integration of the microgrid with the utility system, new synchronization and islanding detection algorithms were developed. The developed algorithms overcome the problem of SCADA and PMU based islanding detection methods such as communication failure and frequency stability. In addition, a real-time energy management system with online optimization was developed to manage the energy resources within the microgrid. The security and privacy were also addressed in both the cyber and physical levels. For the physical design, two techniques were developed to address the physical privacy issues by changing the current and electromagnetic signature. For the cyber level, a security mechanism for IEC 61850 GOOSE messages was developed to address the security shortcomings in the standard

Energy-Efficient Wireless Connectivity and Wireless Charging For Internet-of-Things (IoT) Applications

During the recent years, the Internet-of-Things (IoT) has been rapidly evolving. It is indeed the future of communication that has transformed Things of the real world into smarter devices. To date, the world has deployed billions of “smart” connected things. Predictions say there will be 10’s of billions of connected devices by 2025 and in our lifetime we will experience life with a trillion-node network. However, battery lifespan exhibits a critical barrier to scaling IoT devices. Replacing batteries on a trillion-sensor scale is a logistically prohibitive feat. Self-powered IoT devices seems to be the right direction to stand up to that challenge. The main objective of this thesis is to develop solutions to achieve energy-efficient wireless-connectivity and wireless-charging for IoT applications. In the first part of the thesis, I introduce ultra-low power radios that are compatible with the Bluetooth Low-Energy (BLE) standard. BLE is considered as the preeminent protocol for short-range communications that support transmission ranges up to 10’s of meters. Number of low power BLE transmitter (TX) and receiver (RX) architectures have been designed, fabricated and tested in different planar CMOS and FinFET technologies. The low power operation is achieved by combining low power techniques in both the network and physical layers, namely: backchannel communication, duty-cycling, open-loop transmission/reception, PLL-less architectures, and mixer-first architectures. Further novel techniques have been proposed to further reduce the power the consumption of the radio design, including: a fast startup time and low startup energy crystal oscillators, an antenna-chip co-design approach for quadrature generation in the RF path, an ultra-low power discrete-time differentiator-based Gaussian Frequency Shift Keying (GFSK) demodulation scheme, an oversampling GFSK modulation/demodulation scheme for open loop transmission/reception and packet synchronization, and a cell-based design approach that allows automation in the design of BLE digital architectures. The implemented BLE TXs transmit fully-compliant BLE advertising packet that can be received by commercial smartphone. In the second part of the thesis, I introduce passive nonlinear resonant circuits to achieve wide-band RF energy harvesting and robust wireless power transfer circuits. Nonlinear resonant circuits modeled by the Duffing nonlinear differential equation exhibit interesting hysteresis characteristics in their frequency and amplitude responses that are exploited in designing self-adaptive wireless charging systems. In the magnetic-resonance wireless power transfer scenario, coupled nonlinear resonators are proposed to maintain the power transfer level and efficiency over a range of coupling factors without active feedback control circuitry. Coupling factor depends on the transmission distance, lateral, and angular misalignments between the charging pad and the device. Therefore, nonlinear resonance extends the efficient charging zones of a wireless charger without the requirement for a precise alignment.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/169842/1/omaratty_1.pd