ULTRA-LOW-JITTER, MMW-BAND FREQUENCY SYNTHESIZERS BASED ON A CASCADED ARCHITECTURE

Department of Electrical EngineeringThis thesis presents an ultra-low-jitter, mmW-band frequency synthesizers based on a cascaded architecture. First, the mmW-band frequency synthesizer based on a CP PLL is presented. At the first stage, the CP PLL operating at GHz-band frequencies generated low-jitter output signals due to a high-Q VCO. At the second stage, an ILFM operating at mmW-band frequencies has a wide injection bandwidth, so that the jitter performance of the mmW-band output signals is determined by the GHz-range PLL. The proposed ultra-low-jitter, mmW-band frequency synthesizer based on a CP PLL, fabricated in a 65-nm CMOS technology, generated output signals from GHz-band frequencies to mmW-band frequencies, achieving an RMS jitter of 206 fs and an IPN of ???31 dBc. The active silicon area and the total power consumption were 0.32 mm2 and 42 mW, respectively. However, due to a large in-band phase noise contribution of a PFD and a CP in the CP PLL, this first stage was difficult to achieve an ultra-low in-band phase noise. Second, to improve the in-band phase noise further, the mmW-band frequency synthesizer based on a digital SSPLL is presented. At the first stage, the digital SSPLL operating at GHz-band frequencies generated ultra-low-jitter output signals due to its sub-sampling operation and a high-Q GHz VCO. To minimize the quantization noise of the voltage quantizer in the digital SSPLL, this thesis presents an OSVC as a voltage quantizer while a small amount of power was consumed. The proposed ultra-low-jitter, mmW-band frequency synthesizer fabricated in a 65-nm CMOS technology, generated output signals from GHz-band frequencies to mmW-band frequencies, achieving an RMS jitter of 77 fs and an IPN of ???40 dBc. The active silicon area and the total power consumption were 0.32 mm2 and 42 mW, respectively.clos

High Fidelity Satellite Navigation Receiver Front-End for Advanced Signal Quality Monitoring and Authentication

Over the last several years, interest in utilizing foreign satellite timing and navigation (satnav) signals to augment GPS has grown. Doing so is not without risks; foreign satnav signals must be vetted and determined to be trustworthy before use in military applications. Advanced signal quality monitoring methods can help to ensure that only authentic and reliable satnav signals are utilized. To effectively monitor and authenticate signals, the front-end must impress as little distortions upon the received signal as possible. The purpose of this study is to design, fabricate, and test the performance of a high-fidelity satnav receiver front-end for advanced monitoring of foreign and domestic space vehicle signals

A Scalable 6-to-18 GHz Concurrent Dual-Band Quad-Beam Phased-Array Receiver in CMOS

This paper reports a 6-to-18 GHz integrated phased- array receiver implemented in 130-nm CMOS. The receiver is easily scalable to build a very large-scale phased-array system. It concurrently forms four independent beams at two different frequencies from 6 to 18 GHz. The nominal conversion gain of the receiver ranges from 16 to 24 dB over the entire band while the worst-case cross-band and cross-polarization rejections are achieved 48 dB and 63 dB, respectively. Phase shifting is performed in the LO path by a digital phase rotator with the worst-case RMS phase error and amplitude variation of 0.5° and 0.4 dB, respectively, over the entire band. A four-element phased-array receiver system is implemented based on four receiver chips. The measured array patterns agree well with the theoretical ones with a peak-to-null ratio of over 21.5 dB

A reconfigurable radio-frequency converter IC in 0.18 µm CMOS

This work presents a reconfigurable RF converter for DVB-T television applications using triple-play over GPON. The system takes the DVB-T input, a wavelength division multiplexing (WDM) signal with spectral inversion in the range from 47 MHz to 1000 MHz, up-converts its frequency to the band-pass of a highly selective surface-acoustic wave (SAW) filter centered at 1.3 GHz, and then down-converts it so that it is compatible with the antenna input of conventional television sets. The designed RF converter incorporates two pairs of frequency synthesizer and mixer, based, respectively, on an integer-N phase-locked loop (PLL) with two LC-tank VCOs with 128 coarse tuning bands in the range from 1.35 GHz to 2.7 GHz, and a double-balanced Gilbert cell, modified for better impedance matching and improved linearity. It is fed with regulated supplies compensated in temperature and programmed by an I2 C interface operating on five 16-bit registers. This work presents the experimental characterization of the whole system plus selected cells for stand-alone testing, which have been fabricated in a 0.18 µm CMOS process

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

New strategies for low noise, agile PLL frequency synthesis

Phase-Locked Loop based frequency synthesis is an essential technique employed in wireless communication systems for local oscillator generation. The ultimate goal in any design of frequency synthesisers is to generate precise and stable output frequencies with fast switching and minimal spurious and phase noise. The conflict between high resolution and fast switching leads to two separate integer synthesisers to satisfy critical system requirements. This thesis concerns a new sigma-delta fractional-N synthesiser design which is able to be directly modulated at high data rates while simultaneously achieving good noise performance. Measured results from a prototype indicate that fast switching, low noise and spurious free spectra are achieved for most covered frequencies. The phase noise of the unmodulated synthesiser was measured −113 dBc/Hz at 100 kHz offset from the carrier. The intermodulation effect in synthesisers is capable of producing a family of spurious components of identical form to fractional spurs caused in quantisation process. This effect directly introduces high spurs on some channels of the synthesiser output. Numerical and analytic results describing this effect are presented and amplitude and distribution of the resulting fractional spurs are predicted and validated against simulated and measured results. Finally an experimental arrangement, based on a phase compensation technique, is presented demonstrating significant suppression of intermodulation-borne spurs. A new technique, pre-distortion noise shaping, is proposed to dramatically reduce the impact of fractional spurs in fractional-N synthesisers. The key innovation is the introduction in the bitstream generation process of carefully-chosen set of components at identical offset frequencies and amplitudes and in anti-phase with the principal fractional spurs. These signals are used to modify the Σ-Δ noise shaping, so that fractional spurs are effectively cancelled. This approach can be highly effective in improving spectral purity and reduction of spurious components caused by the Σ-Δ modulator, quantisation noise, intermodulation effects and any other circuit factors. The spur cancellation is achieved in the digital part of the synthesiser without introducing additional circuitry. This technique has been convincingly demonstrated by simulated and experimental results

12???14.5 GHZ DIGITALLY CONTROLLED OSCILLATOR USING A HIGH-RESOLUTION DELTA-SIGMA DIGITAL-TO-ANALOG CONVERTER

Department of Electrical EngineeringThis thesis focuses on the design of digitally-controlled oscillators (DCO) for ultra-low-jitter digital phase-locked-loops (PLL), which requires very fine frequency resolution and low phase noise performance. Before going details of the design, fundamentals of the digital-to-analog converter (DAC), delta-sigma modulator (DSM), LC voltage-controlled oscillator (VCO) are discussed in Chapters 2, 3, and 4 respectively. Detailly, Chapter 2 begins with the basic operations of the digital-toanalog converters. Plus, several types of DACs and their properties are discussed. For instance, resistorbased DAC or current source-based DAC. In Chapter 3, the backgrounds of DSMs are presented. The reason why DSMs are indispensable components in fractional number generation is presented. The meaning of the randomization and noise shaping in DSMs is discussed then high-order noise shaping DSMs are explained as well. Chapter 4, starts with the LC tanks. Integrated passive components are introduced such as spiral inductors, metal-insulator-metal (MIM) capacitors, and metal-oxide-metal (MOM) capacitors. The start-up of the oscillators also explained by using two approaches, the Barkhausen criterion and the negative resistance theory. Then the pros and cons of the CMOS and NMOS type topologies are stated. Finally, the phase noise in oscillators is analyzed by using the Leeson???s equation and the impulse-sensitivity function theory. In chapter 5, the detailed designs of the prototype DCO are presented. The designed DCO consists of 2nd order DSM, string resistor-based DAC, and CMOS-type LC VCO. The frequency resolutions of the proportional and integral path are different but the structures are identical. For the high-performance oscillator, iterative design is required. In the measurements, the designed DCO achieved 17 and 18 bit of frequency resolution in the proportional and integral path respectively, 12-14.5GHz of the frequency tuning range, 50 and 500MHz/V of KVCO for the main and auxiliary loop respectively, and -184.5 dB of figure of merit (FOM). The power consumption is 5.5mW and the prototype was fabricated in TSMC 65nm CMOS process.clos

A high speed serializer/deserializer design

A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design. A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption. A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset). With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage. A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit. The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications

Design of Power Optimized circuit of LC Voltage Controlled Oscillator for use in GSM Handsets

The recent performance requirements for mobile phones have been extending its area of interest. Handsets need to have high resolution graphics, pictures, and applications. Consequently, the requirement for a longer battery life has become a bare necessity. This makes optimization of power a critical issue. Along with this cell phones need to be thin and have light weight. A major portion of the power consumption of the handsets can be attributed to the LC oscillators used in the system. A Voltage Controlled Oscillator plays an important role in any communication system. It provides the frequency signal for down-conversion of input signals and also the carrier signals for the modulating signal. Proper amplitude and low phase noise are two important criteria to achieve suitable performance for a VCO in any transceiver system. The strong combination of low phase noise specifications with very low power consumption (battery operation) forces designers to use LC-VCOs. A great research effort has been done in the design of integrated voltage controlled oscillators (VCOs) using integrated or external resonators, but as their power consumption still cannot be unacceptable, today’s mobile phones commonly use external LC-VCO modules. Inductors used in these oscillators are usually bulky and have high power consumption. The low power LC oscillator increases the standby time, thus improving the battery life. Extended battery life provides processing power at lower clock speeds, enabling low leakage process that optimizes power consumption and increases battery time. Also provides integrated and sophisticated systems with improved power management. The main purpose of this project is to design a circuit for LC VCO to be used in GSM system with a tuning rage of 3-4GHz. Since the phase noise requirement for the system is less than 150dBc/Hz at 20 KHz offset. Also for a GSM system, the size of the inductor used in the oscillator is a major issue in determining its overall size, efforts will be made to optimize the size of the inductor as well