2,251 research outputs found
Feasibility of In-band Full-Duplex Radio Transceivers with Imperfect RF Components: Analysis and Enhanced Cancellation Algorithms
In this paper we provide an overview regarding the feasibility of in-band
full-duplex transceivers under imperfect RF components. We utilize results and
findings from the recent research on full-duplex communications, while
introducing also transmitter-induced thermal noise into the analysis. This
means that the model of the RF impairments used in this paper is the most
comprehensive thus far. By assuming realistic parameter values for the
different transceiver components, it is shown that IQ imaging and
transmitter-induced nonlinearities are the most significant sources of
distortion in in-band full-duplex transceivers, in addition to linear
self-interference. Motivated by this, we propose a novel augmented nonlinear
digital self-interference canceller that is able to model and hence suppress
all the essential transmitter imperfections jointly. This is also verified and
demonstrated by extensive waveform simulations.Comment: 7 pages, presented in the CROWNCOM 2014 conferenc
RF measurements I: signal receiving techniques
For the characterization of components, systems and signals in the RF and
microwave range, several dedicated instruments are in use. In this paper the
fundamentals of the RF-signal sampling technique, which has found widespread
applications in 'digital' oscilloscopes and sampling scopes, are discussed. The
key element in these front-ends is the Schottky diode which can be used either
as an RF mixer or as a single sampler. The spectrum analyser has become an
absolutely indispensable tool for RF signal analysis. Here the front-end is the
RF mixer as the RF section of modern spectrum analysers has a rather complex
architecture. The reasons for this complexity and certain working principles as
well as limitations are discussed. In addition, an overview of the development
of scalar and vector signal analysers is given. For the determination of the
noise temperature of a one-port and the noise figure of a two-port, basic
concepts and relations are shown. A brief discussion of commonly used noise
measurement techniques concludes the paper.Comment: 24 pages, contribution to the CAS - CERN Accelerator School:
Specialised Course on RF for Accelerators; 8 - 17 Jun 2010, Ebeltoft, Denmar
From Theory to Practice: Sub-Nyquist Sampling of Sparse Wideband Analog Signals
Conventional sub-Nyquist sampling methods for analog signals exploit prior
information about the spectral support. In this paper, we consider the
challenging problem of blind sub-Nyquist sampling of multiband signals, whose
unknown frequency support occupies only a small portion of a wide spectrum. Our
primary design goals are efficient hardware implementation and low
computational load on the supporting digital processing. We propose a system,
named the modulated wideband converter, which first multiplies the analog
signal by a bank of periodic waveforms. The product is then lowpass filtered
and sampled uniformly at a low rate, which is orders of magnitude smaller than
Nyquist. Perfect recovery from the proposed samples is achieved under certain
necessary and sufficient conditions. We also develop a digital architecture,
which allows either reconstruction of the analog input, or processing of any
band of interest at a low rate, that is, without interpolating to the high
Nyquist rate. Numerical simulations demonstrate many engineering aspects:
robustness to noise and mismodeling, potential hardware simplifications,
realtime performance for signals with time-varying support and stability to
quantization effects. We compare our system with two previous approaches:
periodic nonuniform sampling, which is bandwidth limited by existing hardware
devices, and the random demodulator, which is restricted to discrete multitone
signals and has a high computational load. In the broader context of Nyquist
sampling, our scheme has the potential to break through the bandwidth barrier
of state-of-the-art analog conversion technologies such as interleaved
converters.Comment: 17 pages, 12 figures, to appear in IEEE Journal of Selected Topics in
Signal Processing, the special issue on Compressed Sensin
Metodologia Per la Caratterizzazione di amplificatori a basso rumore per UMTS
In questo lavoro si presenta una metodologia di
progettazione elettronica a livello di sistema,
affrontando il problema della caratterizzazione dello spazio di progetto dell' amplificatore a basso rumore costituente il primo stadio di un front end a conversione diretta per UMTS realizzato in tecnologia CMOS con lunghezza di canale .18u. La metodologia Ăš sviluppata al fine di valutare in modo quantititativo le specifiche ottime di sistema per il front-end stesso e si basa sul concetto di Piattaforma Analogica, che prevede la costruzione di un modello di prestazioni per il blocco analogico basato su
campionamento statistico di indici di prestazioni del blocco stesso, misurati tramite simulazione di dimensionamenti dei componenti attivi e passivi soddisfacenti un set di equazioni specifico della topologia circuitale. Gli indici di prestazioni vengono successivamente ulizzati per parametrizzare modelli comportamentali utilizzati nelle fasi di ottimizzazione a livello di sistema. Modelli comportamentali atti a rappresentare i sistemi RF sono stati pertanto studiati per ottimizzare la scelta delle metriche di prestazioni. L'ottimizzazione dei set di
equazioni atti a selezionare le configurazione di
interesse per il campionamento ha al tempo stesso richiesto l'approfondimento dei modelli di dispositivi attivi validi in tutte le regioni di funzionamento, e lo studio dettagliato della progettazione degli amplificatori a basso rumore basati su degenerazione induttiva. Inoltre,
il problema della modellizzazione a livello di sistema degli effetti della comunicazione tra LNA e Mixer Ăš stato affrontato proponendo e analizzando diverse soluzioni. Il lavoro ha permesso di condurre un'ottimizzazione del front-end UMTS, giungendo a specifiche ottime a livello di sistema per l'amplificatore stesso
Microwave Measurements Part I: Linear Measurements
An Overview of the most relevant issues concerning RF and microwave linear measurements is presented. Vector Network Analyzer foremost used instrumentation for this kind of measures is describe
Software breadboard study
The overall goal of this study was to develop new concepts and technology for the Comet Rendezvous Asteroid Flyby (CRAF), Cassini, and other future deep space missions which maximally conform to the Functional Specification for the NASA X-Band Transponder (NXT), FM513778 (preliminary, revised July 26, 1988). The study is composed of two tasks. The first task was to investigate a new digital signal processing technique which involves the processing of 1-bit samples and has the potential for significant size, mass, power, and electrical performance improvements over conventional analog approaches. The entire X-band receiver tracking loop was simulated on a digital computer using a high-level programming language. Simulations on this 'software breadboard' showed the technique to be well-behaved and a good approximation to its analog predecessor from threshold to strong signal levels in terms of tracking-loop performance, command signal-to-noise ratio and ranging signal-to-noise ratio. The successful completion of this task paves the way for building a hardware breadboard, the recommended next step in confirming this approach is ready for incorporation into flight hardware. The second task in this study was to investigate another technique which provides considerable simplification in the synthesis of the receiver first LO over conventional phase-locked multiplier schemes and in this approach, provides down-conversion for an S-band emergency receive mode without the need of an additional LO. The objective of this study was to develop methodology and models to predict the conversion loss, input RF bandwidth, and output RF bandwidth of a series GaAs FET sampling mixer and to breadboard and test a circuit design suitable for the X and S-band down-conversion applications
- âŠ