System-level design and RF front-end implementation for a 3-10ghz multiband-ofdm ultrawideband receiver and built-in testing techniques for analog and rf integrated circuits

This work consists of two main parts: a) Design of a 3-10GHz UltraWideBand (UWB) Receiver and b) Built-In Testing Techniques (BIT) for Analog and RF circuits. The MultiBand OFDM (MB-OFDM) proposal for UWB communications has received significant attention for the implementation of very high data rate (up to 480Mb/s) wireless devices. A wideband LNA with a tunable notch filter, a downconversion quadrature mixer, and the overall radio system-level design are proposed for an 11-band 3.4-10.3GHz direct conversion receiver for MB-OFDM UWB implemented in a 0.25mm BiCMOS process. The packaged IC includes an RF front-end with interference rejection at 5.25GHz, a frequency synthesizer generating 11 carrier tones in quadrature with fast hopping, and a linear phase baseband section with 42dB of gain programmability. The receiver IC mounted on a FR-4 substrate provides a maximum gain of 67-78dB and NF of 5-10dB across all bands while consuming 114mA from a 2.5V supply. Two BIT techniques for analog and RF circuits are developed. The goal is to reduce the test cost by reducing the use of analog instrumentation. An integrated frequency response characterization system with a digital interface is proposed to test the magnitude and phase responses at different nodes of an analog circuit. A complete prototype in CMOS 0.35mm technology employs only 0.3mm2 of area. Its operation is demonstrated by performing frequency response measurements in a range of 1 to 130MHz on 2 analog filters integrated on the same chip. A very compact CMOS RF RMS Detector and a methodology for its use in the built-in measurement of the gain and 1dB compression point of RF circuits are proposed to address the problem of on-chip testing at RF frequencies. The proposed device generates a DC voltage proportional to the RMS voltage amplitude of an RF signal. A design in CMOS 0.35mm technology presents and input capacitance <15fF and occupies and area of 0.03mm2. The application of these two techniques in combination with a loop-back test architecture significantly enhances the testability of a wireless transceiver system

A high resolution full-field range imaging system for robotic devices

There has been considerable effort by many researchers to develop a high resolution full-field range imaging system. Traditionally these systems rely on a homodyne technique that modulates the illumination source and shutter speed at some high frequency. These systems tend to suffer from the need to be calibrated to account for changing ambient light conditions and generally cannot provide better than single centimeter range resolution, and even then over a range of only a few meters. We present a system, tested to proof-of-concept stage that is being developed for use on a range of mobile robots. The system has the potential for real-time, sub millimeter range resolution, with minimal power and space requirements

Technology Development for the Caltech Submillimeter Observatory Balanced Receivers

The Caltech Submillimeter Observatory (CSO) is located on top of Mauna Kea, Hawaii, at an altitude of 4.2 km. The existing suite of facility heterodyne receivers covering the submillimeter band is rapidly aging and in need of replacement. To facilitate deep integrations and automated spectral line surveys, a family of remote programmable, synthesized, dual-frequency balanced receivers covering the astronomical important 180 - 720 GHz atmospheric windows is in an advanced stage of development. Installation of the first set of receivers is expected in the spring of 2012. Dual-frequency observation will be an important mode of operation offered by the new facility instrumentation. Two band observations are accomplished by separating the H and V polarizations of the incoming signal and routing them via folded optics to the appropriate polarization sensitive balanced mixer. Scientifically this observation mode facilitates pointing for the higher receiver band under mediocre weather conditions and a doubling of scientific throughput (2 x 4 GHz) under good weather conditions.Comment: 12 pages, 17 figures; IEEE Terahertz Science & Technology, January 2012, Volume 2, Issue

Study to determine potential flight applications and human factors design guidelines for voice recognition and synthesis systems

A study was conducted to determine potential commercial aircraft flight deck applications and implementation guidelines for voice recognition and synthesis. At first, a survey of voice recognition and synthesis technology was undertaken to develop a working knowledge base. Then, numerous potential aircraft and simulator flight deck voice applications were identified and each proposed application was rated on a number of criteria in order to achieve an overall payoff rating. The potential voice recognition applications fell into five general categories: programming, interrogation, data entry, switch and mode selection, and continuous/time-critical action control. The ratings of the first three categories showed the most promise of being beneficial to flight deck operations. Possible applications of voice synthesis systems were categorized as automatic or pilot selectable and many were rated as being potentially beneficial. In addition, voice system implementation guidelines and pertinent performance criteria are proposed. Finally, the findings of this study are compared with those made in a recent NASA study of a 1995 transport concept

A wideband frequency synthesizer for built-in self testing of analog integrated circuits

The cost to test chips has risen tremendously. Additionally, the process for testing all functionalities of both analog and digital part is far from simple. One attractive option is moving some or all of the testing functions onto the chip itself leading to the use of built-in self-tests (BISTs). The frequency generator or frequency synthesizer is a key element of the BIST. It generates the clock frequencies needed for testing. A wide-band frequency synthesizer is designed in the project. The architecture of a PLL is analyzed as well as the modifications carried out. The modified structure has three blocks: basic PLL based frequency synthesizer, frequency down-converter, and output selector. Each of these blocks is analyzed and designed. This frequency synthesizer system overcomes challenges faced by the traditional PLL based frequency synthesizer

Automated Channel Assessment for Single Chip MedRadio Transceivers

Modern implantable and body worn medical devices leverage wireless telemetry to improve patient experience and expand therapeutic options. Wireless medical devices are subject to a unique set of regulations in which monitoring of the available frequency spectrum is a requirement. To this end, implants use software protocols to assess the in-band activity to determine which channel should be used. These software protocols take valuable processing time and possibly degrade the operational lifetime of the battery. Implantable medical devices often take advantage of a single chip transceiver as the physical layer for wireless communications. Embedding the channel assessment task in the transceiver hardware would free the limited resources of the microprocessor. This thesis proposes hardware modifications to existing transceiver architectures which would provide an automated channel assessment means for implantable medical devices. The results are applicable beyond medical device applications and could be employed to benefit any low-power, wireless, battery-operated equipment

Tracking and Data Relay Satellite System (TDRSS) Range and Doppler Tracking System Observation Measurement and Modeling

This document gives detailed descriptions of the tracking services, signal generation and processing, range and Doppler extraction, and the principles and procedures involved in modeling range and Doppler observations via the Tracking and Data Relay Satellite System (TDRSS). Major topics discussed include the following: TDRSS telecommunication services, functional description of the TDRSS, tracking signal generation and processing, range and Doppler observations modeling, angular observed and computed measurement algorithms, and tracking data transmission format