Fault Modeling in Controllable Polarity Silicon Nanowire Circuits

Controllable polarity silicon nanowire transistors are among the promising candidates to replace current CMOS in the near future owing to their superior electrostatic characteristics and advanced functionalities. From a circuit testing point of view, it is unclear if the current CMOS and Fin-FET fault models are comprehensive enough to model all defects of controllable polarity nanowires. In this paper, we deal with the above problem using inductive fault analysis on three-independent-gate silicon nanowire FETs. Simulations revealed that the current fault models, i.e. stuck-open faults, are insufficient to cover all modes of operation. The newly introduced test algorithm for stuck open can adequately capture the malfunction behavior of controllable polarity logic gates in the presence of nanowire break and bridge on polarity terminals

Comparing the impact of power supply voltage on CMOS-and FinFET-based SRAMs in the presence of resistive defects

CMOS technology scaling has reached its limit at the 22 nm technology node due to several factors including Process Variations (PV), increased leakage current, Random Dopant Fluctuation (RDF), and mainly the Short-Channel Effect (SCE). In order to continue the miniaturization process via technology down-scaling while preserving system reliability and performance, Fin Field-Effect Transistors (FinFETs) arise as an alternative to CMOS transistors. In parallel, Static Random-Access Memories (SRAMs) increasingly occupy great part of Systems-on-Chips’ (SoCs) silicon area, making their reliability an important issue. SRAMs are designed to reach densities at the limit of the manufacturing process, making this component susceptible to manufacturing defects, including the resistive ones. Such defects may cause dynamic faults during the circuits’ lifetime, an important cause of test escape. Thus, the identification of the proper faulty behavior taking different operating conditions into account is considered crucial to guarantee the development of more suitable test methodologies. In this context, a comparison between the behavior of a 22 nm CMOS-based and a 20 nm FinFET-based SRAM in the presence of resistive defects is carried out considering different power supply voltages. In more detail, the behavior of defective cells operating under different power supply voltages has been investigated performing SPICE simulations. Results show that the power supply voltage plays an important role in the faulty behavior of both CMOS- and FinFET-based SRAM cells in the presence of resistive defects but demonstrate to be more expressive when considering the FinFET-based memories. Studying different operating temperatures, the results show an expressively higher occurrence of dynamic faults in FinFET-based SRAMs when compared to CMOS technology

Robustness Analysis of Controllable-Polarity Silicon Nanowire Devices and Circuits

Substantial downscaling of the feature size in current CMOS technology has confronted digital designers with serious challenges including short channel effect and high amount of leakage power. To address these problems, emerging nano-devices, e.g., Silicon NanoWire FET (SiNWFET), is being introduced by the research community. These devices keep on pursuing Mooreâs Law by improving channel electrostatic controllability, thereby reducing the Off âstate leakage current. In addition to these improvements, recent developments introduced devices with enhanced capabilities, such as Controllable-Polarity (CP) SiNWFETs, which make them very interesting for compact logic cell and arithmetic circuits. At advanced technology nodes, the amount of physical controls, during the fabrication process of nanometer devices, cannot be precisely determined because of technology fluctuations. Consequently, the structural parameters of fabricated circuits can be significantly different from their nominal values. Moreover, giving an a-priori conclusion on the variability of advanced technologies for emerging nanoscale devices, is a difficult task and novel estimation methodologies are required. This is a necessity to guarantee the performance and the reliability of future integrated circuits. Statistical analysis of process variation requires a great amount of numerical data for nanoscale devices. This introduces a serious challenge for variability analysis of emerging technologies due to the lack of fast simulation models. One the one hand, the development of accurate compact models entails numerous tests and costly measurements on fabricated devices. On the other hand, Technology Computer Aided Design (TCAD) simulations, that can provide precise information about devices behavior, are too slow to timely generate large enough data set. In this research, a fast methodology for generating data set for variability analysis is introduced. This methodology combines the TCAD simulations with a learning algorithm to alleviate the time complexity of data set generation. Another formidable challenge for variability analysis of the large circuits is growing number of process variation sources. Utilizing parameterized models is becoming a necessity for chip design and verification. However, the high dimensionality of parameter space imposes a serious problem. Unfortunately, the available dimensionality reduction techniques cannot be employed for three main reasons of lack of accuracy, distribution dependency of the data points, and finally incompatibility with device and circuit simulators. We propose a novel technique of parameter selection for modeling process and performance variation. The proposed technique efficiently addresses the aforementioned problems. Appropriate testing, to capture manufacturing defects, plays an important role on the quality of integrated circuits. Compared to conventional CMOS, emerging nano-devices such as CP-SiNWFETs have different fabrication process steps. In this case, current fault models must be extended for defect detection. In this research, we extracted the possible fabrication defects, and then proposed a fault model for this technology. We also provided a couple of test methods for detecting the manufacturing defects in various types of CP-SiNWFET logic gates. Finally, we used the obtained fault model to build fault tolerant arithmetic circuits with a bunch of superior properties compared to their competitors