ワイヤレス通信のための先進的な信号処理技術を用いた非線形補償法の研究

The inherit nonlinearity in analogue front-ends of transmitters and receivers have had primary impact on the overall performance of the wireless communication systems, as it gives arise of substantial distortion when transmitting and processing signals with such circuits. Therefore, the nonlinear compensation (linearization) techniques become essential to suppress the distortion to an acceptable extent in order to ensure sufficient low bit error rate. Furthermore, the increasing demands on higher data rate and ubiquitous interoperability between various multi-coverage protocols are two of the most important features of the contemporary communication system. The former demand pushes the communication system to use wider bandwidth and the latter one brings up severe coexistence problems. Having fully considered the problems raised above, the work in this Ph.D. thesis carries out extensive researches on the nonlinear compensations utilizing advanced digital signal processing techniques. The motivation behind this is to push more processing tasks to the digital domain, as it can potentially cut down the bill of materials (BOM) costs paid for the off-chip devices and reduce practical implementation difficulties. The work here is carried out using three approaches: numerical analysis & computer simulations; experimental tests using commercial instruments; actual implementation with FPGA. The primary contributions for this thesis are summarized as the following three points: 1) An adaptive digital predistortion (DPD) with fast convergence rate and low complexity for multi-carrier GSM system is presented. Albeit a legacy system, the GSM, however, has a very strict requirement on the out-of-band emission, thus it represents a much more difficult hurdle for DPD application. It is successfully implemented in an FPGA without using any other auxiliary processor. A simplified multiplier-free NLMS algorithm, especially suitable for FPGA implementation, for fast adapting the LUT is proposed. Many design methodologies and practical implementation issues are discussed in details. Experimental results have shown that the DPD performed robustly when it is involved in the multichannel transmitter. 2) The next generation system (5G) will unquestionably use wider bandwidth to support higher throughput, which poses stringent needs for using high-speed data converters. Herein the analog-to-digital converter (ADC) tends to be the most expensive single device in the whole transmitter/receiver systems. Therefore, conventional DPD utilizing high-speed ADC becomes unaffordable, especially for small base stations (micro, pico and femto). A digital predistortion technique utilizing spectral extrapolation is proposed in this thesis, wherein with band-limited feedback signal, the requirement on ADC speed can be significantly released. Experimental results have validated the feasibility of the proposed technique for coping with band-limited feedback signal. It has been shown that adequate linearization performance can be achieved even if the acquisition bandwidth is less than the original signal bandwidth. The experimental results obtained by using LTE-Advanced signal of 320 MHz bandwidth are quite satisfactory, and to the authors’ knowledge, this is the first high-performance wideband DPD ever been reported. 3) To address the predicament that mobile operators do not have enough contiguous usable bandwidth, carrier aggregation (CA) technique is developed and imported into 4G LTE-Advanced. This pushes the utilization of concurrent dual-band transmitter/receiver, which reduces the hardware expense by using a single front-end. Compensation techniques for the respective concurrent dual-band transmitter and receiver front-ends are proposed to combat the inter-band modulation distortion, and simultaneously reduce the distortion for the both lower-side band and upper-side band signals.電気通信大学201

Mixed-Signal Multimode Radio Software/Hardware Development Platform

Radio frequency power amplifiers (PAs) are the most challenging part of the design of radio systems since they dictate the overall system's performance in terms of power efficiency and distortion generation. The performance is further challenged by modern modulation schemes which are characterized by highly varying signal envelopes. In order to meet the spectrum mask requirements, PAs are usually operated at high power back-off to ensure linearity, at the cost of efficiency. To tackle this issue, many efficiency enhancement techniques have been presented in the literature. In fact, these techniques do increase the PA power efficiency at back-off, however, efficiency enhancement techniques do not ensure the linearity of the PA. Furthermore, these techniques may lead to additional distortion. On the other hand, several linearization techniques have been developed to mitigate the PA nonlinearity problem and allow the PA to operate at less back-off. Digital Pre-Distortion (DPD) technique is gaining more attention, as compared to other linearization techniques, thanks to its simple concept and advancements in digital signal processors (DSP) and signal converters. DPD technique consists of introducing a nonlinear function before the PA so that the overall cascaded system behaves linearly. It was clear from the literature that this technique showed good performance. Yet, it has primarily been validated using commercial test equipment, which has good capabilities, and far from the real world environment in which this technique would be implemented. Indeed, DPDs would need to be implemented in signal processors characterised by limited resources and computational accuracy. This thesis presents an implementation of several DPD models, namely look-up table (LUT), memoryless polynomial and memory polynomial (MP), on a field programmable gate array (FPGA). A novel model reformulation made this implementation possible in fixed-point arithmetic. Measurements were collected to validate the DPD models' implementation and an improvement of the signal quality was recorded in terms of error vector magnitude (EVM) and adjacent channel leakage ratio (ACLR). As many wireless access technologies must continue to coexist, multi-standard radio systems are required to reduce the cost while maintaining the interoperability. This thesis presents a development platform for multimode radio which comprises mixed-signal modules. The platform provides the capacity for hardware and software development. In fact, the FPGA under investigation allowed for the implementation of a baseband transceiver and DPD schemes. In addition, a software tool was developed as a dashboard to control and monitor the system. The radio system in the platform was optimized through the equalization of the feedback receiver frequency response performed through a simultaneous measurement of the amplitude ripple of the transmitter and receiver. Furthermore, a phase-coherent frequency synthesizer was designed to bring more flexibility by allowing the transmitter's carrier frequency to be different from the receiver's frequency

Compact Digital Predistortion for Multi-band and Wide-band RF Transmitters

This thesis is focusing on developing a compact digital predistortion (DPD) system which costs less DPD added power consumptions. It explores a new theory and techniques to relieve the requirement of the number of training samples and the sampling-rate of feedback ADCs in DPD systems. A new theory about the information carried by training samples is introduced. It connects the generalized error of the DPD estimation algorithm with the statistical properties of modulated signals. Secondly, based on the proposed theory, this work introduces a compressed sample selection method to reduce the number of training samples by only selecting the minimal samples which satisfy the foreknown probability information. The number of training samples and complex multiplication operations required for coefficients estimation can be reduced by more than ten times without additional calculation resource. Thirdly, based on the proposed theory, this thesis proves that theoretically a DPD system using memory polynomial based behavioural modes and least-square (LS) based algorithms can be performed with any sampling-rate of feedback samples. The principle, implementation and practical concerns of the undersampling DPD which uses lower sampling-rate ADC are then introduced. Finally, the observation bandwidth of DPD systems can be extended by the proposed multi-rate track-and-hold circuits with the associated algorithm. By addressing several parameters of ADC and corresponding DPD algorithm, multi-GHz observation bandwidth using only a 61.44MHz ADC is achieved, and demonstrated the satisfactory linearization performance of multi-band and continued wideband RF transmitter applications via extensive experimental tests

Digital Signal Processing Techniques Applied to Radio over Fiber Systems

The dissertation aims to analyze different Radio over Fiber systems for the front-haul applications. Particularly, analog radio over fiber (A-RoF) are simplest and suffer from nonlinearities, therefore, mitigating such nonlinearities through digital predistortion are studied. In particular for the long haul A-RoF links, direct digital predistortion technique (DPDT) is proposed which can be applied to reduce the impairments of A-RoF systems due to the combined effects of frequency chirp of the laser source and chromatic dispersion of the optical channel. Then, indirect learning architecture (ILA) based structures namely memory polynomial (MP), generalized memory polynomial (GMP) and decomposed vector rotation (DVR) models are employed to perform adaptive digital predistortion with low complexities. Distributed feedback (DFB) laser and vertical capacity surface emitting lasers (VCSELs) in combination with single mode/multi-mode fibers have been linearized with different quadrature amplitude modulation (QAM) formats for single and multichannel cases. Finally, a feedback adaptive DPD compensation is proposed. Then, there is still a possibility to exploit the other realizations of RoF namely digital radio over fiber (D-RoF) system where signal is digitized and transmits the digitized bit streams via digital optical communication links. The proposed solution is robust and immune to nonlinearities up-to 70 km of link length. Lastly, in light of disadvantages coming from A-RoF and D-RoF, it is still possible to take only the advantages from both methods and implement a more recent form knows as Sigma Delta Radio over Fiber (S-DRoF) system. Second Order Sigma Delta Modulator and Multi-stAge-noise-SHaping (MASH) based Sigma Delta Modulator are proposed. The workbench has been evaluated for 20 MHz LTE signal with 256 QAM modulation. Finally, The 6x2 GSa/s sigma delta modulators are realized on FPGA to show a real time demonstration of S-DRoF system. The demonstration shows that S-DRoF is a competitive competitor for 5G sub-6GHz band applications

A fast engineering approach to high efficiency power amplifier linearization for avionics applications

This PhD thesis provides a fast engineering approach to the design of digital predistortion (DPD) linearizers from several perspectives: i) enhancing the off-line training performance of open-loop DPD, ii) providing robustness and reducing the computational complexity of the parameters identification subsystem and, iii) importing machine learning techniques to favor the automatic tuning of power amplifiers (PAs) and DPD linearizers with several free-parameters to maximize power efficiency while meeting the linearity specifications. One of the essential parts of unmanned aerial vehicles (UAV) is the avionics, being the radio control one of the earliest avionics present in the UAV. Unlike the control signal, for transferring user data (such as images, video, etc.) real-time from the drone to the ground station, large transmission rates are required. The PA is a key element in the transmitter chain to guarantee the data transmission (video, photo, etc.) over a long range from the ground station. The more linear output power, the better the coverage or alternatively, with the same coverage, better SNR allows the use of high-order modulation schemes and thus higher transmission rates are achieved. In the context of UAV wireless communications, the power consumption, size and weight of the payload is of significant importance. Therefore, the PA design has to take into account the compromise among bandwidth, output power, linearity and power efficiency (very critical in battery-supplied devices). The PA can be designed to maximize its power efficiency or its linearity, but not both. Therefore, a way to deal with this inherent trade-off is to design high efficient amplification topologies and let the PA linearizers take care of the linearity requirements. Among the linearizers, DPD linearization is the preferred solution to both academia and industry, for its high flexibility and linearization performance. In order to save as many computational and power resources as possible, the implementation of an open-loop DPD results a very attractive solution for UAV applications. This thesis contributes to the PA linearization, especially on off-line training for open-loop DPD, by presenting two different methods for reducing the design and operating costs of an open-loop DPD, based on the analysis of the DPD function. The first method focuses on the input domain analysis, proposing mesh-selecting (MeS) methods to accurately select the proper samples for a computationally efficient DPD parameter estimation. Focusing in the MeS method with better performance, the memory I-Q MeS method is combined with feature extraction dimensionality reduction technique to allow a computational complexity reduction in the identification subsystem by a factor of 65, in comparison to using the classical QR-LS solver and consecutive samples selection. In addition, the memory I-Q MeS method has been proved to be of crucial interest when training artificial neural networks (ANN) for DPD purposes, by significantly reducing the ANN training time. The second method involves the use of machine learning techniques in the DPD design procedure to enlarge the capacity of the DPD algorithm when considering a high number of free parameters to tune. On the one hand, the adaLIPO global optimization algorithm is used to find the best parameter configuration of a generalized memory polynomial behavioral model for DPD. On the other hand, a methodology to conduct a global optimization search is proposed to find the optimum values of a set of key circuit and system level parameters, that properly combined with DPD linearization and crest factor reduction techniques, can exploit at best dual-input PAs in terms of maximizing power efficiency along wide bandwidths while being compliant with the linearity specifications. The advantages of these proposed techniques have been validated through experimental tests and the obtained results are analyzed and discussed along this thesis.Aquesta tesi doctoral proporciona unes pautes per al disseny de linealitzadors basats en predistorsió digital (DPD) des de diverses perspectives: i) millorar el rendiment del DPD en llaç obert, ii) proporcionar robustesa i reduir la complexitat computacional del subsistema d'identificació de paràmetres i, iii) incorporació de tècniques d'aprenentatge automàtic per afavorir l'auto-ajustament d'amplificadors de potència (PAs) i linealitzadors DPD amb diversos graus de llibertat per poder maximitzar l’eficiència energètica i al mateix temps acomplir amb les especificacions de linealitat. Una de les parts essencials dels vehicles aeris no tripulats (UAV) _es l’aviònica, sent el radiocontrol un dels primers sistemes presents als UAV. Per transferir dades d'usuari (com ara imatges, vídeo, etc.) en temps real des del dron a l’estació terrestre, es requereixen taxes de transmissió grans. El PA _es un element clau de la cadena del transmissor per poder garantir la transmissió de dades a grans distàncies de l’estació terrestre. A major potència de sortida, més cobertura o, alternativament, amb la mateixa cobertura, millor relació senyal-soroll (SNR) la qual cosa permet l’ús d'esquemes de modulació d'ordres superiors i, per tant, aconseguir velocitats de transmissió més altes. En el context de les comunicacions sense fils en UAVs, el consum de potència, la mida i el pes de la càrrega útil són de vital importància. Per tant, el disseny del PA ha de tenir en compte el compromís entre ample de banda, potència de sortida, linealitat i eficiència energètica (molt crític en dispositius alimentats amb bateries). El PA es pot dissenyar per maximitzar la seva eficiència energètica o la seva linealitat, però no totes dues. Per tant, per afrontar aquest compromís s'utilitzen topologies amplificadores d'alta eficiència i es deixa que el linealitzador s'encarregui de garantir els nivells necessaris de linealitat. Entre els linealitzadors, la linealització DPD és la solució preferida tant per al món acadèmic com per a la indústria, per la seva alta flexibilitat i rendiment. Per tal d'estalviar tant recursos computacionals com consum de potència, la implementació d'un DPD en lla_c obert resulta una solució molt atractiva per a les aplicacions UAV. Aquesta tesi contribueix a la linealització del PA, especialment a l'entrenament fora de línia de linealitzadors DPD en llaç obert, presentant dos mètodes diferents per reduir el cost computacional i augmentar la fiabilitat dels DPDs en llaç obert. El primer mètode se centra en l’anàlisi de l’estadística del senyal d'entrada, proposant mètodes de selecció de malla (MeS) per seleccionar les mostres més significatives per a una estimació computacionalment eficient dels paràmetres del DPD. El mètode proposat IQ MeS amb memòria es pot combinar amb tècniques de reducció del model del DPD i d'aquesta manera poder aconseguir una reducció de la complexitat computacional en el subsistema d’identificació per un factor de 65, en comparació amb l’ús de l'algoritme clàssic QR-LS i selecció de mostres d'entrenament consecutives. El segon mètode consisteix en l’ús de tècniques d'aprenentatge automàtic pel disseny del DPD quan es considera un gran nombre de graus de llibertat (paràmetres) per sintonitzar. D'una banda, l'algorisme d’optimització global adaLIPO s'utilitza per trobar la millor configuració de paràmetres d'un model polinomial amb memòria generalitzat per a DPD. D'altra banda, es proposa una estratègia per l’optimització global d'un conjunt de paràmetres clau per al disseny a nivell de circuit i sistema, que combinats amb linealització DPD i les tècniques de reducció del factor de cresta, poden maximitzar l’eficiència de PAs d'entrada dual de gran ample de banda, alhora que compleixen les especificacions de linealitat. Els avantatges d'aquestes tècniques proposades s'han validat mitjançant proves experimentals i els resultats obtinguts s'analitzen i es discuteixen al llarg d'aquesta tesi

Digital predistortion of RF amplifiers using baseband injection for mobile broadband communications

Radio frequency (RF) power amplifiers (PAs) represent the most challenging design parts of wireless transmitters. In order to be more energy efficient, PAs should operate in nonlinear region where they produce distortion that significantly degrades the quality of signal at transmitter’s output. With the aim of reducing this distortion and improve signal quality, digital predistortion (DPD) techniques are widely used. This work focuses on improving the performances of DPDs in modern, next-generation wireless transmitters. A new adaptive DPD based on an iterative injection approach is developed and experimentally verified using a 4G signal. The signal performances at transmitter output are notably improved, while the proposed DPD does not require large digital signal processing memory resources and computational complexity. Moreover, the injection-based DPD theory is extended to be applicable in concurrent dual-band wireless transmitters. A cross-modulation problem specific to concurrent dual-band transmitters is investigated in detail and novel DPD based on simultaneous injection of intermodulation and cross-modulation distortion products is proposed. In order to mitigate distortion compensation limit phenomena and memory effects in highly nonlinear RF PAs, this DPD is further extended and complete generalised DPD system for concurrent dual-band transmitters is developed. It is clearly proved in experiments that the proposed predistorter remarkably improves the in-band and out-of-band performances of both signals. Furthermore, it does not depend on frequency separation between frequency bands and has significantly lower complexity in comparison with previously reported concurrent dual-band DPDs

Contribution to dimensionality reduction of digital predistorter behavioral models for RF power amplifier linearization

The power efficiency and linearity of radio frequency (RF) power amplifiers (PAs) are critical in wireless communication systems. The main scope of PA designers is to build the RF PAs capable to maintain high efficiency and linearity figures simultaneously. However, these figures are inherently conflicted to each other and system-level solutions based on linearization techniques are required. Digital predistortion (DPD) linearization has become the most widely used solution to mitigate the efficiency versus linearity trade-off. The dimensionality of the DPD model depends on the complexity of the system. It increases significantly in high efficient amplification architectures when considering current wideband and spectrally efficient technologies. Overparametrization may lead to an ill-conditioned least squares (LS) estimation of the DPD coefficients, which is usually solved by employing regularization techniques. However, in order to both reduce the computational complexity and avoid ill-conditioning problems derived from overparametrization, several efforts have been dedicated to investigate dimensionality reduction techniques to reduce the order of the DPD model. This dissertation contributes to the dimensionality reduction of DPD linearizers for RF PAs with emphasis on the identification and adaptation subsystem. In particular, several dynamic model order reduction approaches based on feature extraction techniques are proposed. Thus, the minimum number of relevant DPD coefficients are dynamically selected and estimated in the DPD adaptation subsystem. The number of DPD coefficients is reduced, ensuring a well-conditioned LS estimation while demanding minimum hardware resources. The presented dynamic linearization approaches are evaluated and compared through experimental validation with an envelope tracking PA and a class-J PA The experimental results show similar linearization performance than the conventional LS solution but at lower computational cost.La eficiencia energetica y la linealidad de los amplificadores de potencia (PA) de radiofrecuencia (RF) son fundamentales en los sistemas de comunicacion inalambrica. El principal objetivo a alcanzar en el diserio de amplificadores de radiofrecuencia es lograr simultaneamente elevadas cifras de eficiencia y de linealidad. Sin embargo, estas cifras estan inherentemente en conflicto entre si, y se requieren soluciones a nivel de sistema basadas en tecnicas de linealizacion. La linealizacion mediante predistorsion digital (DPD) se ha convertido en la solucion mas utilizada para mitigar el compromise entre eficiencia y linealidad. La dimension del modelo del predistorsionador DPD depende de la complejidad del sistema, y aumenta significativamente en las arquitecturas de amplificacion de alta eficiencia cuando se consideran los actuales anchos de banda y las tecnologfas espectralmente eficientes. El exceso de parametrizacion puede conducir a una estimacion de los coeficientes DPD, mediante minimos cuadrados (LS), mal condicionada, lo cual generalmente se resuelve empleando tecnicas de regularizacion. Sin embargo, con el fin de reducir la complejidad computacional y evitar dichos problemas de mal acondicionamiento derivados de la sobreparametrizacion, se han dedicado varies esfuerzos para investigar tecnicas de reduccion de dimensionalidad que permitan reducir el orden del modelo del DPD. Esta tesis doctoral contribuye a aportar soluciones para la reduccion de la dimension de los linealizadores DPD para RF PA, centrandose en el subsistema de identificacion y adaptacion. En concrete, se proponen varies enfoques de reduccion de orden del modelo dinamico, basados en tecnicas de extraccion de caracteristicas. El numero minimo de coeficientes DPD relevantes se seleccionan y estiman dinamicamente en el subsistema de adaptacion del DPD, y de este modo la cantidad de coeficientes DPD se reduce, lo cual ademas garantiza una estimacion de LS bien condicionada al tiempo que exige menos recursos de hardware. Las propuestas de linealizacion dinamica presentados en esta tesis se evaluan y comparan mediante validacion experimental con un PA de seguimiento de envolvente y un PA tipo clase J. Los resultados experimentales muestran unos resultados de linealizacion de los PA similares a los obtenidos cuando se em plea la solucion LS convencional, pero con un coste computacional mas reducido.Postprint (published version

Compensation of nonlinear distortion in RF amplifiers for mobile communications

Compensation of nonlinear distortion of power amplifiers in mobile communications is an important requirement for improving power consumption performance while maintaining efficiency, since mobile phone became an essential accessory for everyone nowadays. This problem demands a good power amplifier model, in order to develop an effective predistortion system. Current researches are focused on modelling and predistortion of power amplifiers with memory, as well as memoryless ones. Different methods for modelling are used, as the Volterra series, polynomial models, look-up tables, the Hammerstein models, the Wiener models, and artificial intelligence systems. For predistortion feedback, feedforward and digital predistortion techniques are used. Among digital predistortion methods there are artificial intelligence systems, used in this thesis for linearization of power amplifier. This thesis presents developed robust method for modelling power amplifiers without memory effects and gives a comparison of proposed method with least squares method. Also, this research presents two novel techniques based on artificial intelligence systems for modelling and predistortion of highly nonlinear power amplifier with memory. The first approach is based on artificial neural networks, while the second one uses adaptive fuzzy logic systems. Forward and inverse models of power amplifier are created with both proposed methods. Superiority of artificial intelligence systems over partial least squares method is presented. Developed models are employed in a cascade to make a linearized system. Verification of proposed methods is carried out through the signal performance parameters and spectra of measured signal and signal from predistortion system. The feasibility and performances of the proposed digital predistortions are examined by simulations and experiments. The comparison of proposed methods is given to present advantages/disadvantages of both methods. The achieved distortion suppression from 72.2% to 93.6% and spectral regrowth improvement from 11.4 dB to 16.2 dB prove that the proposed methods have great ability to compensate the nonlinear distortion in power amplifier

An Adaptive Fuzzy Logic System for the Compensation of Nonlinear Distortion in Wireless Power Amplifiers

Computational intelligent systems are becoming an increasingly attractive solution for power amplifier (PA) behavioural modelling, due to their excellent approximation capability. This paper utilizes an adaptive fuzzy logic system (AFLS) for the modelling of the highly nonlinear MIMIX CFH2162-P3 PA. Moreover, PA’s inverse model based also on AFLS has been developed in order to act as a pre-distorter unit. Driving an LTE 1.4 MHz 64 QAM signal at 880 MHz as centre frequency at PA’s input, very good modelling performance was achieved, for both PA’s forward and inverse dynamics. A comparative study of AFLS and neural networks (NN) has been carried out to establish AFLS as an effective, robust, and easy-to-implement baseband model, which is suitable for inverse modelling of PAs and capable to be used as an effective digital pre-distorter. Pre-distortion system based on AFLS, achieved distortion suppression of 84.2%, compared to the 48.4% gained using the NN-based equivalent schem

Single Input Single Output Digital Pre-Distortion at Millimeter Wave Frequencies for Phased Arrays

The limiting fact that is impeding the increase in data rate in the current generation of wireless communication is the limited available spectrum in the sub-6 GHz bands. This has motivated the shift to higher frequencies such as millimeter waves (mm-wave) and terahertz frequencies where modulation bandwidth of several hundreds of MHz can be utilized to increase the communication link capacity. The deployment of high data rate mm-wave base stations will highly depend on the maximum achievable equivalent isotropic radiated power (EIRP) and on the ability to generate reliable and error free wideband signals. High EIRP and high efficiency operation can be achieved by using active phased arrays operated deep into the power amplifiers (PAs) nonlinear region. In this work, a low power and low complexity compensation schemes to mitigate the impairments exhibited by phase arrays driven with wideband signals and high efficient nonlinear PAs at mm-wave frequencies are proposed. Digital pre-distortion (DPD) techniques can provide an attractive solution to linearize high efficiency and high EIRP nonlinear phased arrays at mm-wave frequencies. However, the viable deployment of DPD solutions call for the reduction in the power consumption of the transmitter observation receiver (TOR) feedback path required to train the DPD function. To that end, a low power DPD scheme for linearizing mm-wave hybrid beamforming antenna systems is presented. The proposed DPD scheme exploits the modularity of hybrid beamforming systems. During the training phase, the constituent sub-arrays, are categorized, into (i) the main sub-array that exhibits non-linear distortion and is to be linearized, and (ii) the auxiliary sub-arrays that operate in the backoff region to avoid nonlinearity. To produce the error signal necessary to train the DPD function (and compensate for the distortions exhibited by the main sub-array), the signals transmitted by the main and auxiliary sub-arrays are combined. This error signal is captured using a TOR with low dynamic range and is digitized using a low-bit resolution analog-to-digital converter (ADC). Proof-of-concept validation experiments are conducted by applying the proposed DPD system to linearize an off-the-shelf hybrid-beamforming array comprised of four 64-element sub-arrays, operating at 28 GHz and driven with up to 800 MHz orthogonal frequency-division multiplexing (OFDM) modulated signals. Using the proposed DPD scheme, a TOR with a 4-bit ADC was sufficient to improve the adjacent channel power ratio (ACPR) by 10 dB and the error vector magnitude (EVM) improved from 5.8% to 1.6%. These results are similar to those obtained using a TOR with 16-bit ADCs. Reducing the complexity of the DPD scheme for phased arrays is also of primordial importance to the successful deployment of DPD solutions. For instance, the DPD function needs to be desensitize to the load modulation effects exhibited by large antenna systems and be able to linearize phased arrays at different steering angles. To address the challenges associated with the load modulation for phased arrays, we propose a generalized SISO DPD scheme as solution to minimize the EVM variation at different steering angles. The measurement results of the proposed scheme, using a 400 MHz OFDM signal with subcarriers modulated using 256 QAM and on a commercial 64-elements beamforming array, was able to maintain the EVM below 2% across the full steering range. This solution, however, failed to maintain the ACPR below -45 dBc. The effect of tapering on the load modulation and the array nonlinearity is also analysed. The measurement results using different tapers are used to validate the theory and the simulation results. Using tapering, the ACPR and EVM variation before and after DPD were minimized versus steering angles. For instance, using taper setting 2, the ACPR and EVM are maintained below -46 dBc and 1% from -38° to 45° and below -42.3 dBc and 1.8% from -45° to 45° respectively. Better results are measured when tapering is used in conjunction with the proposed generalized DPD scheme. In that case, the ACPR is improved from -35.5 to at worst -46.4 dBc and at best -50 dBc and the EVM is improved from at worst 4.5% to at worst 1.2% and at best 0.85%. The EVM is also maintained below 0.95% from -39° to 45°