COMPARISON OF INTERCONNECT FAILURES OF ELECTRONIC COMPONENTS MOUNTED ON FR-4 BOARDS WITH SN37PB AND SN3.0AG0.5CU SOLDERS UNDER RAPID LOADING CONDITIONS.

Electronic circuit boards can experience rapid loading through shock or vibration events during their lives; these events can happen in transportation, manufacture, or in field conditions. Due to the lead-free migration, it is necessary to evaluate how this rapid loading affects the durability of a leading lead free solder alternative (Sn3.0Ag0.5Cu) assemblies as compared with traditional eutectic lead based solder Sn37Pb assemblies. A literature review showed that there is little agreement on the fatigue behavior of Sn37Pb solder assemblies and Sn3.0Ag0.5Cu solder assemblies subjected to rapid loading. To evaluate the failure behavior of Sn37Pb and Sn3.0Ag0.5Cu solder assemblies under rapid loading conditions, leadless chip resistors (LCR), ball grid arrays (BGA), small outline integrated circuits (SOIC), and small outline transistors (SOT) were subjected to four point bend tests via a servo-hydraulic testing machine at printed wiring board (PWB) strain rates greater than 0.1/s. The PWB strain was the metric used to evaluate the failures. The PBGAs and LCRs were examined with both Sn37Pb and Sn3.0Ag0.5Cu solders. There was no significant difference found in the resulting test data for the behavior of the two solder assembly types in the high cycle fatigue regime. PBGA assemblies with both solders were also evaluated at a higher strain rate, approximately 1/s, using drop testing. There was no discernable difference found between the assemblies as well as no difference in the failure rate of the PBGAs at this higher strain rate. The PWB strain was converted to an equivalent solder stress index using finite element analysis. This equivalent stress index value was used to compare the results from the LCR and BGA testing for Sn37Pb and Sn3.0Ag0.5Cu. Independently generated BGA data that differed with respect to many testing variables was adjusted and incorporated to this comparison. The resulting plot did not show any significant differences between the behaviors of the two solder assemblies under rapid loading outside of the ultra low cycle fatigue regime, where the assemblies with Sn37Pb solder outperformed the assemblies with SnAgCu solder

Characterising Solder Materials from Random Vibration Response of their Interconnects in BGA Packaging

Solder interconnection in electronic packaging is the weakest link, thus driving the reliability of electronic modules and systems. Improving interconnection integrity in safety-critical applications is vital in enhancing application reliability. This investigation qualifies the random vibration response of five essential solder compositions in ball grid array (BGA) solder joints used in safety-critical applications. The solder compositions are eutectic Sn63Pb37 and SnAgCu (SAC) 305, 387, 396, and 405. Computer-aided engineering (CAE) employing ANSYS FEA and SolidWorks software is implemented in this investigation. The solder Sn63Pb37 deformed least at 0.43 µm, followed by SAC396 at 0.58 µm, while SAC405 deformed highest at 0.88 µm. Further analysis demonstrates that possession of higher elastic modulus and mass density culminates in lower solder joint deformation. Stress is concentrated at the periphery of the solder joints in contact with the printed circuit board (PCB). The SAC396 solder accumulates the lowest stress of 14.1 MPa, followed by SAC405 at 17.9 MPa, while eutectic Sn63Pb37 accrues the highest at 34.6 MPa. Similarly, strain concentration is found at the interface between the solder joint and copper pad on PCB. SAC405 acquires the lowest elastic strain magnitude of 0.0011 mm/mm, while SAC305 records the highest strain of 0.002 mm/mm. These results demonstrate that SAC405 solder has maximum and SAC387 solder has minimum fatigue lives

Thermomechanical fatigue failure of interfaces in lead-free solders

The European Union Waste Electrical and Electronic Equipment Directive (WEEE) and Restriction of Hazardous Substances Directive (RoHS) banned lead from electronic systems from July 1, 2006 onwards, which has led to much interest in leadfree solders in the past years. Among several lead-free solder alternatives, SnAgCu is a widely accepted replacement due to its better creep-fatigue resistance and microstructural stability. SnAgCu has been extensively studied in the past decade, however, there are still issues to be resolved concerning solder reliability, the underlying mechanisms of thermo-mechanical fatigue failure, fatigue life predictions and the overall effect of decreasing component size, driven by the ongoing miniaturization trend. This thesis aims to scientifically contribute to this subject by a coupled experimental-numerical approach. In solder joint reliability, the bump/pad interface has a crucial role, the quality of which is determined by the metallization and interfacial defects. Solder balls, solder paste and cast eutectic SnAgCu are reflowed on Cu, Ni/Au and Cu/Ni(V)/Au metallization layers and the substrate influence on the bulk and interfacial metallurgy is examined. The damage propagation at SnAgCu soldered joints on Cu and Ni/Au substrates are investigated and microstructure related damage localization is identified as the dominant failure mechanism. Therefore, continuum damage approaches are believed to be inadequate for solder joint reliability predictions. Nano-indentation and tensile testing is used for the mechanical characterization of SnAgCu. An assessment on indentation parameters for solders is conducted and the influence of the Ag content on material properties of SnAgCu is presented. One of the main causes of ball grid array (BGA) failure is thermo-mechanical fatigue crack propagation in the solder, which is almost always observed at the bump/pad junction. Motivated by this fact, a combined experimental-numerical study on the cyclic mechanical response of SnAgCu/Ni-Au interface is conducted. In this study, damage evolution at the bond/pad interface is characterized by dedicated fatigue tests. Local deformations leading to crack propagation are simulated by separation of interfaces through a cohesive zone approach. Solder joints are tested under cyclic shear and cyclic tension for different specimen sizes and strain amplitudes. Two different damagemechanisms are observed: local deformations in the bulk and at the bonding interface. The interfacial failure mode is typically favored at a high initial stress, and a small solder volume. Crack propagation is simulated by an irreversible linear traction-separation cohesive zone law accompanied by a non-linear interfacial damage parameter. Later, tensile and shear experiments are used to characterize the cohesive zone parameters for the normal and the tangential opening, respectively. Interfacial fatigue damage in BGA solders is caused by the difference in coefficient of thermal expansion (CTE) of the materials in the package. Apart from this thermal incompatibility in the package, Sn based solders are themselves prone to thermal fatigue damage due to the intrinsic thermal anisotropy of the ß-Sn phase. Thermal fatigue causes local deformations especially at the grain boundaries. Hence, the thermal fatigue response of bulk SnAgCu is investigated as well. Bulk SnAgCu specimens are thermally cycled between -40 and 125¿C and mechanically tested afterwards in order to quantify the thermal fatigue damage. A size dependent cyclic softening behavior is observed. Test specimens are individually modeled including the microstructure and local crystallographic orientations, on the basis of orientation imaging scans (OIM). Both thermal cycling and tensile testing are imposed as boundary conditions. Reproducing the experimental results in the simulations, parameters of a cohesive zone based intergranular fatigue damagemodel are identified. Finally, the intergranular damage law characterized in this study is combined with the bump/pad interfacial damage law, and a 2Dmicrostructure-incorporated fatigue life prediction tool is established. Using this tool, it is shown that the failure mode of a soldered joint depends extensively on its geometry. The model presented above is extended to 3D for a more complete description of the problem. To provide the microstructural input, a database containing OIM scans of several SnAgCu solder balls is constructed. A missing constituent in the model so far, interfacial defects, i.e. voids, are examined statistically using newly manufactured BGA packages, revealing information on their size, position and frequency. Combining all the data collected, i.e. material properties, microstructure, defects, local damage laws, a 3D slice model from a BGA package is constructed. The slice model contains a single solder ball connecting the board and the chip. A series of case studies is created using experimental input such as different microstructures and initial defects allowing a statistical analysis. Fatigue life of these models are predicted and the results are validated by failure distribution analyses of BGA packages provided by the industry. Here the critical solder ball assumption is made: if a solder ball fails, the electrical circuit of the BGA package is open, thus the package fails. Setting a critical damage value for the interfaces accumulating fatigue damage, a good agreement with the experiments and simulations is obtained. It is seen that microstructural modeling allows to predict and understand the scatter in the solder ball fatigue life observed in reality. Finally, the effect of solder ball size and geometry on interconnect reliability is dis cussed on the basis of numerical analyses. For this purpose, a geometry factor and a microstructure factor is defined, and their influence on damage evolution is discusse

Numerical simulations for reliability assessment of lead-free solder interconnections in BGA packages

This work presents the results of computer-aided numerical simulations for the reliability assessment of lead-free solder interconnections in BGA packages. The finite element and Monte Carlo methods were employed for the macroscale structural and the mesoscale microstructural simulations, respectively. The major reliability tests for electronic component boards, i.e. thermal cycling, power cycling and drop impact tests, were simulated via the finite element method. The results provide a feasible tool for a better understanding of the observed failure modes in the reliability tests. The lifetime predictions based on the simulation results are helpful for the lifetime estimations of the BGA packages. The temperature effects on the drop impact reliability of the BGA packages were successfully elucidated by the finite element numerical experiments. In addition, a new algorithm was developed in order to predict dynamic recrystallization in solder interconnections during thermal cycling. The approach was realized by combining the Potts model based Monte Carlo method and the finite element method. The correlation between real time and Monte Carlo simulation time was established with the help of the in situ test results. Recrystallization with the presence of intermetallic particles in the solder matrix was simulated by introducing the energy amplification factors in the particle-affected deformation regions. The present algorithm predicted both the incubation period of the recrystallization as well as the growth tendency of the recrystallized regions in a way consistent with the experimental findings

Thermomechanical fatigue failure of interfaces in lead-free solders

The European Union Waste Electrical and Electronic Equipment Directive (WEEE) and Restriction of Hazardous Substances Directive (RoHS) banned lead from electronic systems from July 1, 2006 onwards, which has led to much interest in leadfree solders in the past years. Among several lead-free solder alternatives, SnAgCu is a widely accepted replacement due to its better creep-fatigue resistance and microstructural stability. SnAgCu has been extensively studied in the past decade, however, there are still issues to be resolved concerning solder reliability, the underlying mechanisms of thermo-mechanical fatigue failure, fatigue life predictions and the overall effect of decreasing component size, driven by the ongoing miniaturization trend. This thesis aims to scientifically contribute to this subject by a coupled experimental-numerical approach. In solder joint reliability, the bump/pad interface has a crucial role, the quality of which is determined by the metallization and interfacial defects. Solder balls, solder paste and cast eutectic SnAgCu are reflowed on Cu, Ni/Au and Cu/Ni(V)/Au metallization layers and the substrate influence on the bulk and interfacial metallurgy is examined. The damage propagation at SnAgCu soldered joints on Cu and Ni/Au substrates are investigated and microstructure related damage localization is identified as the dominant failure mechanism. Therefore, continuum damage approaches are believed to be inadequate for solder joint reliability predictions. Nano-indentation and tensile testing is used for the mechanical characterization of SnAgCu. An assessment on indentation parameters for solders is conducted and the influence of the Ag content on material properties of SnAgCu is presented. One of the main causes of ball grid array (BGA) failure is thermo-mechanical fatigue crack propagation in the solder, which is almost always observed at the bump/pad junction. Motivated by this fact, a combined experimental-numerical study on the cyclic mechanical response of SnAgCu/Ni-Au interface is conducted. In this study, damage evolution at the bond/pad interface is characterized by dedicated fatigue tests. Local deformations leading to crack propagation are simulated by separation of interfaces through a cohesive zone approach. Solder joints are tested under cyclic shear and cyclic tension for different specimen sizes and strain amplitudes. Two different damagemechanisms are observed: local deformations in the bulk and at the bonding interface. The interfacial failure mode is typically favored at a high initial stress, and a small solder volume. Crack propagation is simulated by an irreversible linear traction-separation cohesive zone law accompanied by a non-linear interfacial damage parameter. Later, tensile and shear experiments are used to characterize the cohesive zone parameters for the normal and the tangential opening, respectively. Interfacial fatigue damage in BGA solders is caused by the difference in coefficient of thermal expansion (CTE) of the materials in the package. Apart from this thermal incompatibility in the package, Sn based solders are themselves prone to thermal fatigue damage due to the intrinsic thermal anisotropy of the ß-Sn phase. Thermal fatigue causes local deformations especially at the grain boundaries. Hence, the thermal fatigue response of bulk SnAgCu is investigated as well. Bulk SnAgCu specimens are thermally cycled between -40 and 125¿C and mechanically tested afterwards in order to quantify the thermal fatigue damage. A size dependent cyclic softening behavior is observed. Test specimens are individually modeled including the microstructure and local crystallographic orientations, on the basis of orientation imaging scans (OIM). Both thermal cycling and tensile testing are imposed as boundary conditions. Reproducing the experimental results in the simulations, parameters of a cohesive zone based intergranular fatigue damagemodel are identified. Finally, the intergranular damage law characterized in this study is combined with the bump/pad interfacial damage law, and a 2Dmicrostructure-incorporated fatigue life prediction tool is established. Using this tool, it is shown that the failure mode of a soldered joint depends extensively on its geometry. The model presented above is extended to 3D for a more complete description of the problem. To provide the microstructural input, a database containing OIM scans of several SnAgCu solder balls is constructed. A missing constituent in the model so far, interfacial defects, i.e. voids, are examined statistically using newly manufactured BGA packages, revealing information on their size, position and frequency. Combining all the data collected, i.e. material properties, microstructure, defects, local damage laws, a 3D slice model from a BGA package is constructed. The slice model contains a single solder ball connecting the board and the chip. A series of case studies is created using experimental input such as different microstructures and initial defects allowing a statistical analysis. Fatigue life of these models are predicted and the results are validated by failure distribution analyses of BGA packages provided by the industry. Here the critical solder ball assumption is made: if a solder ball fails, the electrical circuit of the BGA package is open, thus the package fails. Setting a critical damage value for the interfaces accumulating fatigue damage, a good agreement with the experiments and simulations is obtained. It is seen that microstructural modeling allows to predict and understand the scatter in the solder ball fatigue life observed in reality. Finally, the effect of solder ball size and geometry on interconnect reliability is dis cussed on the basis of numerical analyses. For this purpose, a geometry factor and a microstructure factor is defined, and their influence on damage evolution is discusse

Dynamic Mechanical and Failure Properties of Solder Joints

Ph.DDOCTOR OF PHILOSOPH

Analysis of Printed Circuit Boards strains using finite element analysis and digital image correlation

This paper investigates the use of digital image correlation (DIC) and finite element analysis for strain measurement on Printed Board Circuits (PCBs). Circuit boards (PCBs) are designed to mechanically support and electrically connect an electronic component assembly. Due to screw assemblies, the surface level differences on which the PCB is placed, the process of assembling the electronic components induces a certain state of stress and deformation in the PCB. The main components affected are microprocessors due to the way they are glued to PCBs with BGA - Ball grid arrays (BGA). Digital Image Correlation (DIC) is a full-field contactless optical method for measuring displacements and strain in experimental testing, based on the correlation of images taken during test. The experimental setup is realized with Dantec Q-400 system used for image capture and Istra 4D software for image correlations and data analyses. The maximum level of the obtained strain is compared with the allowable limit. Finite element analysis (FEA) is a numerical method of analysis for stresses and strain in structures of any given geometry

Board level drop testing of advanced IC packaging

Master'sMASTER OF ENGINEERIN

The durability of solder joints under thermo-mechanical loading; application to Sn-37Pb and Sn-3.8Ag-0.7Cu lead-free replacement alloy

Solder joints in electronic packages provide mechanical, electrical and thermal connections. Hence, their reliability is also a major concern to the electronic packaging industry. Ball Grid Arrays (BGAs) are a very common type of surface mount technology for electronic packaging. This work primarily addresses the thermo-mechanical durability of BGAs and is applied to the exemplar alloys; traditional leaded solder and a popular lead-free solder. Isothermal mechanical fatigue tests were carried out on 4-ball test specimens of the lead-free (Sn-3.8Ag-0.7Cu) and leaded (Sn-37Pb) solder under load control at room temperature, 35°C and 75°C. As well as this, a set of combined thermal and mechanical cycling tests were carried out, again under load control with the thermal cycles either at a different frequency from the mechanical cycles (not-in-phase) or at the same frequency (both in phase and out-of-phase). The microstructural evaluation of both alloys was investigated by carrying out a series of simulated ageing tests, coupled with detailed metallurgical analysis and hardness testing. The results were treated to produce stress-life, cyclic behaviour and creep curves for each of the test conditions. Careful calibration allowed the effects of substrate and grips to be accounted for and so a set of strain-life curves to be produced. These results were compared with other results from the literature taking into account the observations on microstructure made in the ageing tests. It is generally concluded that the TMF performance is better for the Sn-Ag-Cu alloy than for the Sn-Pb alloy, when expressed as stress-life curves. There is also a significant effect on temperature and phase for each of the alloys, the Sn-Ag-Cu being less susceptible to these effects. When expressed as strain life, the effects of temperature, phase and alloy type are much diminished. Many of these conclusions coincided with only parts of the literature and reasons for the remaining differences are advanced