Loss Quantization of Reflectarray Antenna Based on Organic Substrate Materials

This paper presents novel loss quantization of reflectarray elements based on organic substrate materials. Three differently composed substrate materials derived from recycled materials have been characterized for their dielectric properties using a broadband analysis technique. The materials show low dielectric permittivity values of 1.81, 1.62 and 1.84 for X-band frequency range. In order to estimate the reflection loss of for the three substrates a mathematical relation has been established using empirical data generated by computer simulated models. The reliability of the proposed model has been established by simulation and fabrication of unit reflectarray rectangular patch elements on three proposed substrate substrates. A broadband frequency response has been depicted by scattering parameter analysis of unit elements with 10% fractional bandwidth of 312, 340 and 207 MHz for RCP50, RCR75 and RNP50 substrate respectively

Recent Advances in Antenna Design for 5G Heterogeneous Networks

The aim of this book is to highlight up to date exploited technologies and approaches in terms of antenna designs and requirements. In this regard, this book targets a broad range of subjects, including the microstrip antenna and the dipole and printed monopole antenna. The varieties of antenna designs, along with several different approaches to improve their overall performance, have given this book a great value, in which makes this book is deemed as a good reference for practicing engineers and under/postgraduate students working in this field. The key technology trends in antenna design as part of the mobile communication evolution have mainly focused on multiband, wideband, and MIMO antennas, and all have been clearly presented, studied and implemented within this book. The forthcoming 5G systems consider a truly mobile multimedia platform that constitutes a converged networking arena that not only includes legacy heterogeneous mobile networks but advanced radio interfaces and the possibility to operate at mm wave frequencies to capitalize on the large swathes of available bandwidth. This provides the impetus for a new breed of antenna design that, in principle, should be multimode in nature, energy efficient, and, above all, able to operate at the mm wave band, placing new design drivers on the antenna design. Thus, this book proposes to investigate advanced 5G antennas for heterogeneous applications that can operate in the range of 5G spectrums and to meet the essential requirements of 5G systems such as low latency, large bandwidth, and high gains and efficiencies

Demonstrating Reflectarray Behavior At Infrared

Reflectarrays are traditionally passive, planar microstrip antenna devices designed for reflected phase manipulation at each individual antenna element making up the array. By varying the phase response across the surface with the antenna elements, reflectarrays allows a planar surface to exhibit electromagnetically an arbitrary geometry, such as a spherical surface. Initially proposed as a low-cost replacement for bulky parabolic reflectors, reflectarrays have been successfully developed and utilized at both RF and millimeter-wave frequencies. From the standpoint of an optical systems designer, adapting low-frequency reflectarray technology to develop a sub-millimeter and infrared reflectarray (SMIR) would provide a highly desirable alternative to similarly behaved polished or diffractive optical devices. Compared to traditional optical reflectors, SMIRs should be cheaper to fabricate, have a smaller physical footprint, allow for utility stacking, and encourage direct integration of aberration correction. To demonstrate the feasibility of utilizing reflectarray technology at infrared (IR), a simple SMIR proof of concept has been successfully designed, fabricated, and tested. The SMIR is comprised of three independent arrays or stripes of a single size element on a coated optical flat. Actual reflectarray elements consist of variable size patches that exhibit higher operating bandwidths than reflectarrays utilizing other types of elements and are easier to fabricate at small dimensions. For testing, each stripe element has been chosen to exhibit a unique phase shift for measurement using an IR interferometer. Preliminary investigation of future reflectarray development is also discussed. Emphasis is placed on improving operating bandwidth, development of a planar focusing element, and aberration correction. With further development, SMIR technology should present a powerful tool for low cost, flexible optical system design

Gradient metasurfaces: a review of fundamentals and applications

In the wake of intense research on metamaterials the two-dimensional analogue, known as metasurfaces, has attracted progressively increasing attention in recent years due to the ease of fabrication and smaller insertion losses, while enabling an unprecedented control over spatial distributions of transmitted and reflected optical fields. Metasurfaces represent optically thin planar arrays of resonant subwavelength elements that can be arranged in a strictly or quasi periodic fashion, or even in an aperiodic manner, depending on targeted optical wavefronts to be molded with their help. This paper reviews a broad subclass of metasurfaces, viz. gradient metasurfaces, which are devised to exhibit spatially varying optical responses resulting in spatially varying amplitudes, phases and polarizations of scattered fields. Starting with introducing the concept of gradient metasurfaces, we present classification of different metasurfaces from the viewpoint of their responses, differentiating electrical-dipole, geometric, reflective and Huygens' metasurfaces. The fundamental building blocks essential for the realization of metasurfaces are then discussed in order to elucidate the underlying physics of various physical realizations of both plasmonic and purely dielectric metasurfaces. We then overview the main applications of gradient metasurfaces, including waveplates, flat lenses, spiral phase plates, broadband absorbers, color printing, holograms, polarimeters and surface wave couplers. The review is terminated with a short section on recently developed nonlinear metasurfaces, followed by the outlook presenting our view on possible future developments and perspectives for future applications.Comment: Accepted for publication in Reports on Progress in Physic

Antennas and Propagation

This Special Issue gathers topics of utmost interest in the field of antennas and propagation, such as: new directions and challenges in antenna design and propagation; innovative antenna technologies for space applications; metamaterial, metasurface and other periodic structures; antennas for 5G; electromagnetic field measurements and remote sensing applications

Multi-band reflectarray antennas in Ku and THz frequency bands

Printed reflectarrays are low-cost, low-profile high gain antennas demonstrating distinctive advantages over conventional parabolic reflectors and phased-arrays. The flat, low weight reflecting surface of a reflectarray makes it an attractive alternative with respect to bulky parabolic reflectors specially for space and satellite systems. As compared to high-cost phased-array antennas, with incorporation of solid state devices, reflectarrays are able to demonstrate electronic beam scanning in a very low-cost way. A distinctive advantage of a reflectarray antenna lies in its potential to be readily designed as a multi-band antenna which demonstrates independent performance at several frequencies. A characteristic that is difficult to achieve using conventional parabolic reflectors. The aim of this thesis is to present low-cost, simple, multi-band printed reflectarray antennas in Ku and THz frequency bands. In Ku band we present a dual-band reflectarray performing at 12 and 14 GHz and a quad-band reflectarray antenna performing at 12, 13, 14 and 15.5 GHz. The presented prototypes benefit from the advantage of having a single-layer structure which reduces the design complexity as well as the fabrication cost. In addition, multi-band reflectarrays are able to perform at any polarization due to the dual-linear polarized design of their unit-cells. Furthermore, the design of the unit-cell is such that, at each frequency, the phase response depends on only one parameter of the cell. This advantage eliminates the need for time consuming optimizations. Based on proposed unit-cells dual-band and quad-band reflectarrays with arbitrary beam direction versus frequency have been simulated, fabricated and measured. Simulation and measurement results as well demonstrate the satisfactory independent performance of the prototypes at each intended frequency. In THz region, for the first time we present a tri-band unit-cell based on which reflectarray prototypes performing at the three frequencies 0.7, 1.0 and 1.5 THz, are designed. The presented reflectarrays possess all the advantages of those designed for Ku band with the additional advantage of having high resistivity silicon as the substrate thanks to a sophisticated fabrication process. The use of silicon as substrate is a big advantage since it facilitates the integration of solid state devices for reconfigurability. Based on the proposed unit-cell reflectarray samples with arbitrary independent performance at each frequency are designed, simulated, fabricated and measured. Measurement results obtained using a THz-TDS (Terahertz Time-Domain Spectroscopy) measurement system, demonstrate the satisfactory independent performance of the reflectarray samples at each frequency. This thesis also presents a dual-band, dual-polarized reconfigurable unit-cell for beam-scanning reflectarray operating at 12 and 14 GHz. The cell however suffers from high-cross-polarization level. A chessboard cell arrangement is proposed to mitigate the high cross-polarization level at the reflectarray far-field region. Simulation results show the effectiveness of the chessboard arrangement in eliminating the cross-polarization allowing the design of a low-cross polarization reconfigurable reflectarray antenna out of a unit-cell with high cross-polarization level. Finally, the thesis presents the concept of a versatile flat prism which is a reflectarray with a pre-designed frequency-scanning behaviour. The limitations and challenges as well as solutions for implementation of such a device are presented and discussed

Design of new radiating systems and phase shifters for 5G communications at millimeter-wave frequencies

With the arrival of the new generation of communications, known as 5G, the systems that constitute it must offer better performance in terms of data speed, latency and connection density than the previous generation of communications. For 5G, an allocation of the frequency ranges that will support future wireless communications has been established. This allocation is formed by a range of frequencies corresponding to bands below 6 GHz and the other range of frequencies includes bands above 24 GHz. In the latter frequency range, which includes part of the millimeter-wave frequency band (from 30 GHz to 300 GHz), the development of new radio frequency (RF) components is necessary because their design and manufacture is a technological challenge. As the frequency that supports wireless communications increases, propagation losses also increase. Therefore, these losses must be compensated by the radiating systems in 5G to make these communications possible. The RF devices that make up these new systems must provide high antenna gain, be power efficient and offer spatial reconfigurability of the radiated signal. In this thesis, the main objective is the design of both guided and radiating RF devices to provide design solutions for future 5G systems at millimeter-wave frequencies. In particular, the contributions made have been to the design of phase shifters and antenna arrays. To improve efficiency at millimeter-wave frequencies, these devices have been designed in waveguide technology. Phase shifters are essential RF devices to control the phase shift of the electromagnetic wave that will be radiated to a certain spatial direction by an antenna array. The design of beamforming networks requires the implementation of phase shifters that produce a fixed or variable phase shift value. However, the design and fabrication of these devices at millimeter-wave frequencies is a complex task. In this thesis, four designs of waveguide phase shifters that produce both fixed and variable phase shift are presented. For phase shifters that provide a fixed phase shift, the value of this phase shift along the frequency is tuned in a desired manner by using periodic structures with higher symmetries. These types of configurations provide both flexibility in the design process and improved electromagnetic performance such as greater operating bandwidth. All the phase shifters have been implemented in gap-waveguide technology to demonstrate its effectiveness in these devices for millimeter-wave frequencies. Regarding the radiating systems, two feeding strategies have been considered in the design process. First, the design of a 70 GHz centered antenna array implemented in gap-waveguide technology combined with the use of separate waveguides in E-plane is proposed. In this design, the feed is guided through a waveguide corporate-feed network. Second, the design of a reflectarray whose unit cells are formed using three-dimensional geometries is presented. In this case, the feeding is done in free space by radiation from a source antenna. In the previous designs, the fabrication of the prototypes was done by 3D printing based on stereolithography. Finally, using unit cells with three-dimensional geometries, the design of radiating devices with more complex functionalities such as reflection/transmission with high directivity and reconfiguration of the reflected radiation by means of graphene structures are proposed.Con la llegada de la nueva generación de comunicaciones, denominada 5G, los sistemas que la conforman deben ofrecer unas mejores prestaciones en términos de velocidad de datos, latencia y densidad de conexiones respecto a la generación de comunicaciones anterior. Para 5G se ha establecido una asignación de los rangos de frecuencia que van a soportar las futuras comunicaciones inalámbricas. Esta asignación se compone por un rango de frecuencias correspondiente a las bandas por debajo de los 6 GHz y el otro rango de frecuencias engloba a las bandas por encima de los 24 GHz. En este ´ultimo rango de frecuencias, en el cual están incluidas parte de la banda de las frecuencias milimétricas (desde 30 GHz a 300 GHz), es necesario el desarrollo de nuevos componentes de radiofrecuencia (RF) ya que su diseño y fabricación supone un reto tecnológico. Al aumentar la frecuencia que soporta las comunicaciones inalámbricas, las pérdidas por propagación también aumentan. Es por ello por lo que estas pérdidas deben ser compensadas por los sistemas radiantes en 5G para que las comunicaciones sean posibles. Los dispositivos de RF que componen estos nuevos sistemas deben proporcionar una alta ganancia de antena, ser eficientes en términos de potencia y ofrecer reconfigurabilidad espacial de la señal radiada. En esta tesis, el objetivo principal es el diseño de dispositivos de RF tanto guiados como radiantes para ofrecer soluciones de diseño a los futuros sistemas 5G en frecuencias milimétricas. De manera particular, las contribuciones realizadas han sido al diseño de desfasadores y agrupaciones de antenas. Para mejorar la eficiencia en frecuencias milimétricas, estos dispositivos han sido diseñados en tecnología en guía de ondas. Los desfasadores son dispositivos RF esenciales para controlar el desfase de la onda electromagnética que será radiada hacia una cierta dirección espacial por una agrupación de antenas. Las redes de beamforming tienen la necesidad de implementar en su diseño desfasadores que producen un valor de desfase fijo o variable. Sin embargo, el diseño y fabricación de estos dispositivos en frecuencias milimétricas resulta una tarea de alta dificultad. En esta tesis se presenta cuatro diseños de desfasadores en guía de onda que producen un desfase tanto fijo como variable. Para los desfasadores que proporcionan un desfase fijo, el valor de este desfase a lo largo de la frecuencia es ajustado de manera deseada mediante el uso de estructuras periódicas con simetrías superiores. Este tipo de configuraciones proporcionan tanto flexibilidad en el proceso de diseño como una mejora de las características electromagnéticas como puede ser un mayor ancho de banda de operación. Todos los desfasadores realizados han sido implementados en tecnología gap waveguide para demostrar su efectividad en estos dispositivos para frecuencias milimétricas. Respecto a los sistemas radiantes, se han considerado dos estrategias de alimentación en el proceso diseño. En primer lugar, se propone el diseño de un array centrado a 70 GHz implementado en tecnología gap waveguide combinado con el uso de guías de onda separadas en plano E. En este diseño, la alimentación es guiada a través de una red de alimentación corporativa en guía de onda. En segundo lugar, se presenta el diseño de un reflectarray cuyas celdas unitarias son formadas mediante geometrías tridimensionales. En este caso, la alimentación se hace en el espacio libre mediante la radiación de una antena fuente. En los anteriores diseños, la fabricación de los prototipos se realizó mediante impresión 3D basado en estereolitografía. Finalmente, a través del uso de celdas unitarias con geometrías tridimensionales, se proponen el diseño de dispositivos radiantes con funcionalidades más complejas como la reflexión/transmisión con alta directividad y la reconfiguración de la radiación reflejada mediante estructuras con grafeno.Tesis Univ. Granada

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance