Electrostatic discharge protection circuit for high-speed mixed-signal circuits

ESD, the discharge of electrostatically generated charges into an IC, is one of the most important reliability problems for ultra-scaled devices. This electrostatic charge can generate voltages of up to tens of kilovolts. These very high voltages can generate very high electric fields and currents across semiconductor devices, which may result in dielectric damage or melting of semiconductors and contacts. It has been reported that up to 70% of IC failures are caused by ESD. Therefore, it’s necessary to design a protection circuit for each pin that discharges the ESD energy to the ground. As the devices are continuously scaling down, while ESD energy remains the same, they become more vulnerable to ESD stress. This higher susceptibility to ESD damage is due to thinner gate oxides and shallower junctions. Furthermore, higher operating frequency of the scaled technologies enforces lower parasitic capacitance of the ESD protection circuits. As a result, increasing the robustness of the ESD protection circuits with minimum additional parasitic capacitance is the main challenge in state of the art CMOS processes. Providing a complete ESD immunity for any circuit involves the design of proper protection circuits for I/O pins in addition to an ESD clamp between power supply pins. In this research both of these aspects are investigated and optimized solutions for them are reported. As Silicon Controlled Rectifier (SCR) has the highest ESD protection level per unit area, ESD protection for I/O pins is provided by optimizing the first breakdown voltage and latch-up immunity of SCR family devices. The triggering voltage of SCR is reduced by a new implementation of gate-substrate triggering technique. Furthermore, a new device based on SCR with internal darlington pair is introduced that can provide ESD protection with very small parasitic capacitance. Besides reducing triggering voltage, latch-up immunity of SCR devices is improved using two novel techniques to increase the holding voltage and the holding current. ESD protection between power rails is provided with transient clamps in which the triggering circuit keeps the clamp “on” during the ESD event. In this research, two new clamps are reported that enhance the triggering circuit of the clamp. The first method uses a CMOS thyristor element to provide enough delay time while the second method uses a flip flop to latch the clamp into “on” state at the ESD event. Moreover, the stability of transient clamps is analyzed and it’s been shown that the two proposed clamps have the highest stability compared to other state of the art ESD clamps. Finally, in order to investigate the impact of ESD protection circuits on high speed applications a current mode logic (CML) driver is designed in 0.13μm CMOS technology. The protection for this driver is provided using both MOS-based and SCR-based protection methods. Measurement results show that, compared to MOS-based protection, SCR-based protection has less impact on the driver performance due to its lower parasitic capacitance

Analysis of design strategies for RF ESD problems in CMOS circuits

This thesis analyses the design strategies used to protect RF circuits that are implemented in CMOS technologies. It investigates, in detail, the physical mechanisms involved when a ggNMOS structure is exposed to an ESD event and undergoes snapback. The understanding gained is used to understand why the performance of the current RF ESD clamp is poor and suggestions are made as to how the performance of ggNMOS clamps can be improved beyond the current body of knowledge. The ultimate aim is to be able to design effective ESD protection clamps whilst minimising the effect the circuit has on RF I/O signals. A current ggNMOS based RF ESD I/O protection circuit is analysed in detail using a Transmission Line Pulse (TLP) tester. This is shown to be a very effective diagnostic tool by showing many characteristics of the ggNMOS during the triggering and conducting phase of the ESD event and demonstrate deficiencies in the clamp design. The use of a FIB enhances the analysis by allowing the isolation of individual components in the circuit and therefore their analysis using the TLP tester. SPICE simulations are used to provide further commentary on the debate surrounding the specification required of a TLP tester for there to be a good correlation between a TLP test and the industry standard Human Body Model (HBM) ESD test. Finite element simulations are used to probe deeper in to the mechanisms involved when a ggNMOS undergoes snapback especially with regard to the contribution parasitic components within the ggNMOS make to the snapback process. New ggNMOS clamps are proposed which after some modification are shown to work. Some of the finite element experiments are repeated in a 0.18μπ7. process CMOS test chip and a comparison is made between the two sets of results. In the concluding chapter understanding that has been gained from previous chapters is combined with the published body of knowledge to suggest and explain improvements in the design of a ggNMOS for RF and standard applications. These improvements will improve homogeneity of ggNMOS operation thus allowing the device size to be reduced and parasitic loading for a given ESD performance. These techniques can also be used to ensure that the ESD current does not take an unintended path through the chip

Optimal design of a 2.4 GHz CMOS low noise amplifier

In most RF receivers, the Low Noise Amplifier (LNA) is normally the first component, whose performance is very critical. For the LNA architecture that uses source degeneration inductors and cascode topology, the performance depends largely on the performance of the inductors. All the parasitics associated with the inductors should be thoroughly analyzed and taken into consideration while designing the LNA. The work presented in this thesis can be broadly classified as follows: optimization of the LNA design with respect to all the parasitics associated with the on-chip spiral inductors, modeling high performance inductors, which are embedded in the silicon substrate and analysis of parasitic effects from the Electro Static Discharge (ESD) protection circuitry on the performance of the LNA. A methodology has been developed such that the LNA design can be optimized in the presence of an ESD protection circuitry in order to achieve the required input impedance match. This optimization procedure is presented for all possible placements of the ESD protection circuitry at the input of the LNA, that is, with respect to the gate inductor being realized on-chip or off-chip or a combination of on-chip and off-chip inductors. The thesis presents the procedure to vary the source inductance and gate inductance values in the presence of parasitic ESD capacitance in order to optimize LNA design such that the required input impedance match is maintained

Analysis and Design of Electrostatic Discharge Protection Devices and Circuits

An electrostatic discharge (ESD) is a spontaneous electrical current that flows between two objects at different electrical potentials. ESD currents can reach several amps and are typically in the order of tens of nanoseconds. Concerning microelectronics, on-chip protection against ESD events has become a main concern on the reliability of IC as dimensions continue to shrink. ESD currents could lead to on-chip voltages that are high enough to cause MOS gate oxide breakdown. ICs can thus be damaged by human handling, contact with machinery, packaging, board assembling, etc. The main goal of this study was to analyze the effectiveness of two-stage ESD protection circuits by means of mixed mode TCAD simulations. Two-dimensional device simulations were carried out using T-Suprem4 and Taurus-Medici software from Synopsis. Also, a TCAD input deck calibration for an NXP Semiconductors¿ proprietary 0.14m¿ CMOS technology was realized. In addition, two aspects on the transparency of ESD protections were studied. An excessive leakage problem found in a real product was analyzed in TCAD. Furthermore, a new approach for distributed ESD protection design for broadband applications is also discussed, resulting in improved RF performance.Pérez Monteagudo, JM. (2010). Analysis and Design of Electrostatic Discharge Protection Devices and Circuits. http://hdl.handle.net/10251/21061.Archivo delegad

CDM Robust & Low Noise ESD protection circuits

In spite of significant progress during last couple of decades, ESD still affects production yields, manufacturing costs, product quality, product reliability and profitability. The objective of an ESD protection circuit is to create a harmless shunting path for the static electricity before it damages the sensitive electronic circuits. As the devices are scaling down, while ESD energy remains the same, VLSIs are becoming more vulnerable to ESD stress. This higher susceptibility to ESD damage is due to thinner gate oxides and shallower junctions. Furthermore, higher operating frequency of the scaled technologies enforces lower parasitic capacitance of the ESD protection circuits. Hence, increasing the robustness of the ESD protection circuits with minimum additional parasitic capacitance is the main challenge in state of the art CMOS processes. Furthermore with scaling, the integration of analog blocks such as ADC, PLL’s, DLL’s, oscillator etc. on digital chips has provided cheap system on chip (SOC) solutions. However, when analog and digital chip are combined into single mixed-signal chip, on-chip noise coupling from the digital to the analog circuitry through ESD protection circuits becomes a big concern. Thus, increasing supply noise isolation while ensuring the ESD protection robustness is also a big challenge. In this thesis, several ESD protection circuits and devices have been proposed to address the critical issues like increased leakage current, slower turn-on time of devices, increased susceptibility to power supply isolation etc. The proposed ESD protection circuits/devices have been classified into two categories: Pad based ESD protection in which the ESD protection circuits are placed in the I/O pads, and Rail based ESD in which ESD protection circuit is placed between power supplies. In our research, both these aspects have been investigated. The Silicon Controlled Rectifier (SCR) based devices have been used for Pad ESD protection as they have highest ESD protection level per unit area. Two novel devices Darlington based SCR (DSCR) and NMOS Darlington based SCR (NMOS-DSCR) having faster turn-on time, lower first breakdown voltage and low capacitance have been proposed. The transient clamps have been investigated and optimized for Rail based ESD protection. In this research, we have addressed the issue of leakage current in transient clamps. A methodology has been purposed to reduce the leakage current by more than 200,000 times without having major impact on the ESD performance. Also, the issue of noise coupling from digital supply to analog supply through the ESD protection circuits has been addressed. A new transient clamp has been proposed to increase the power supply noise isolation. Finally, a new methodology of placement of analog circuit with respect to transient clamp has been proposed to further increase the power supply noise isolation

Advances in Solid State Circuit Technologies

This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields

VLSI Design

This book provides some recent advances in design nanometer VLSI chips. The selected topics try to present some open problems and challenges with important topics ranging from design tools, new post-silicon devices, GPU-based parallel computing, emerging 3D integration, and antenna design. The book consists of two parts, with chapters such as: VLSI design for multi-sensor smart systems on a chip, Three-dimensional integrated circuits design for thousand-core processors, Parallel symbolic analysis of large analog circuits on GPU platforms, Algorithms for CAD tools VLSI design, A multilevel memetic algorithm for large SAT-encoded problems, etc

Silica and Silicon Based Nanostructures

Silica and silicon-based nanostructures are now well-understood materials for which the technologies are mature. The most obvious applications, such as electronic devices, have been widely explored over the last two decades. The aim of this Special Issue is to bring together the state of the art in the field and to enable the emergence of new ideas and concepts for silicon and silica-based nanostructures

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book