Dynamic Voltage Scaling Aware Delay Fault Testing

The application of Dynamic Voltage Scaling (DVS) to reduce energy consumption may have a detrimental impact on the quality of manufacturing tests employed to detect permanent faults. This paper analyses the influence of different voltage/frequency settings on fault detection within a DVS application. In particular, the effect of supply voltage on different types of delay faults is considered. This paper presents a study of these problems with simulation results. We have demonstrated that the test application time increases as we reduce the test voltage. We have also shown that for newer technologies we do not have to go to very low voltage levels for delay fault testing. We conclude that it is necessary to test at more than one operating voltage and that the lowest operating voltage does not necessarily give the best fault cover

Variation Resilient Adaptive Controller for Subthreshold Circuits

Subthreshold logic is showing good promise as a viable ultra-low-power circuit design technique for power-limited applications. For this design technique to gain widespread adoption, one of the most pressing concerns is how to improve the robustness of subthreshold logic to process and temperature variations. We propose a variation resilient adaptive controller for subthreshold circuits with the following novel features: new sensor based on time-to-digital converter for capturing the variations accurately as digital signatures, and an all-digital DC-DC converter incorporating the sensor capable of generating an operating operating Vdd from 0V to 1.2V with a resolution of 18.75mV, suitable for subthreshold circuit operation. The benefits of the proposed controller is reflected with energy improvement of up to 55% compared to when no controller is employed. The detailed implementation and validation of the proposed controller is discussed

A 10-bit Charge-Redistribution ADC Consuming 1.9 μW at 1 MS/s

This paper presents a 10 bit successive approximation ADC in 65 nm CMOS that benefits from technology scaling. It meets extremely low power requirements by using a charge-redistribution DAC that uses step-wise charging, a dynamic two-stage comparator and a delay-line-based controller. The ADC requires no external reference current and uses only one external supply voltage of 1.0 V to 1.3 V. Its supply current is proportional to the sample rate (only dynamic power consumption). The ADC uses a chip area of approximately 115--225 μm2. At a sample rate of 1 MS/s and a supply voltage of 1.0 V, the 10 bit ADC consumes 1.9 μW and achieves an energy efficiency of 4.4 fJ/conversion-step

A software controlled voltage tuning system using multi-purpose ring oscillators

This paper presents a novel software driven voltage tuning method that utilises multi-purpose Ring Oscillators (ROs) to provide process variation and environment sensitive energy reductions. The proposed technique enables voltage tuning based on the observed frequency of the ROs, taken as a representation of the device speed and used to estimate a safe minimum operating voltage at a given core frequency. A conservative linear relationship between RO frequency and silicon speed is used to approximate the critical path of the processor. Using a multi-purpose RO not specifically implemented for critical path characterisation is a unique approach to voltage tuning. The parameters governing the relationship between RO and silicon speed are obtained through the testing of a sample of processors from different wafer regions. These parameters can then be used on all devices of that model. The tuning method and software control framework is demonstrated on a sample of XMOS XS1-U8A-64 embedded microprocessors, yielding a dynamic power saving of up to 25% with no performance reduction and no negative impact on the real-time constraints of the embedded software running on the processor

Combined Time and Information Redundancy for SEU-Tolerance in Energy-Efficient Real-Time Systems

Recently the trade-off between energy consumption and fault-tolerance in real-time systems has been highlighted. These works have focused on dynamic voltage scaling (DVS) to reduce dynamic energy dissipation and on time redundancy to achieve transient-fault tolerance. While the time redundancy technique exploits the available slack time to increase the fault-tolerance by performing recovery executions, DVS exploits slack time to save energy. Therefore we believe there is a resource conflict between the time-redundancy technique and DVS. The first aim of this paper is to propose the usage of information redundancy to solve this problem. We demonstrate through analytical and experimental studies that it is possible to achieve both higher transient fault-tolerance (tolerance to single event upsets (SEU)) and less energy using a combination of information and time redundancy when compared with using time redundancy alone. The second aim of this paper is to analyze the interplay of transient-fault tolerance (SEU-tolerance) and adaptive body biasing (ABB) used to reduce static leakage energy, which has not been addressed in previous studies. We show that the same technique (i.e. the combination of time and information redundancy) is applicable to ABB-enabled systems and provides more advantages than time redundancy alone

A RISC-V Vector Processor With Simultaneous-Switching Switched-Capacitor DC-DC Converters in 28 nm FDSOI

This work demonstrates a RISC-V vector microprocessor implemented in 28 nm FDSOI with fully integrated simultaneous-switching switched-capacitor DC-DC (SC DC-DC) converters and adaptive clocking that generates four on-chip voltages between 0.45 and 1 V using only 1.0 V core and 1.8 V IO voltage inputs. The converters achieve high efficiency at the system level by switching simultaneously to avoid charge-sharing losses and by using an adaptive clock to maximize performance for the resulting voltage ripple. Details about the implementation of the DC-DC switches, DC-DC controller, and adaptive clock are provided, and the sources of conversion loss are analyzed based on measured results. This system pushes the capabilities of dynamic voltage scaling by enabling fast transitions (20 ns), simple packaging (no off-chip passives), low area overhead (16%), high conversion efficiency (80%-86%), and high energy efficiency (26.2 DP GFLOPS/W) for mobile devices

A survey of dynamic power optimization techniques

One of the most important considerations for the current VLSI/SOC design is power, which can be classified into power analysis and optimization. In this survey, the main concepts of power optimization including the sources and policies are introduced. Among the various approaches, dynamic power management (DPM), which implies to change devices states when they are not working at the highest speed or at their full capacity, is the most efficient one. Our explanations accompanying the figures specify the abstract concepts of DPM. This paper briefly surveys both heuristic and stochastic policies and discusses their advantages and disadvantages