Dynamic Frequency and Voltage Control for a Multiple Clock Domain Microarchitecture

We describe the design, analysis, and performance of an on-line algorithm to dynamically control the frequency/voltage of a Multiple Clock Domain (MCD) microarchitecture. The MCD microarchitecture allows the frequency/voltage of micrprocessor regions to be adjusted independently and dynamically, allowing enery savings when the frequency of some regions can be reduced without significantly impacting performance. Our algorithm achieves on average a 19.0% reduction in Energy Per Instriction (EPI), a 3.2% increase in Cycles Per Instruction (CPI), a 16.7% improvement in Energy–Delay Product, and a Power Savings to Performance Degradation ratio of 4.6. Traditional frequency/voltage scaling techniques which apply reductions globally to a fully synchronous processor achieve a Power Savings to Performance Degradation ratio of only 2–3. Our Energy–Delay Product improvement is 85.5% of what has been achieved using an off–line algorithm. These results were achieved using a broad range of applications from the MediaBench, Olden, and Spec2000 benchmark suites using an algorithm we show to require minimal hardware resources

Using MCD-DVS for dynamic thermal management performance improvement

With chip temperature being a major hurdle in microprocessor design, techniques to recover the performance loss due to thermal emergency mechanisms are crucial in order to sustain performance growth. Many techniques for power reduction in the past and some on thermal management more recently have contributed to alleviate this problem. Probably the most important thermal control technique is dynamic voltage and frequency scaling (DVS) which allows for almost cubic reduction in power with worst-case performance penalty only linear. So far, DVS techniques for temperature control have been studied at the chip level. Finer grain DVS is feasible if a globally-asynchronous locally-synchronous (GALS) design style is employed. GALS, also known as multiple-clock domain (MCD), allows for an independent voltage and frequency control for each one of the clock domains that are part of the chip. There are several studies on DVS for GALS that aim to improve energy and power efficiency but not temperature. This paper proposes and analyses the usage of DVS at the domain level to control temperature in a clustered MCD microarchitecture with the goal of improving the performance of applications that do not meet the thermal constraints imposed by the designers.Peer ReviewedPostprint (published version

Frontend frequency-voltage adaptation for optimal energy-delay/sup 2/

In this paper, we present a clustered, multiple-clock domain (CMCD) microarchitecture that combines the benefits of both clustering and globally asynchronous locally synchronous (GALS) designs. We also present a mechanism for dynamically adapting the frequency and voltage of the frontend of the CMCD with the goal to optimize the energy-delay/sup 2/ product (ED2P). Our mechanism has minimal hardware cost, is entirely self-adjustable, does not depend on any thresholds, and achieves results close to optimal. We evaluate it on 16 SPEC 2000 applications and report 17.5% ED2P reduction on average (80% of the upper bound).Peer ReviewedPostprint (published version

Impact of parameter variations on circuits and microarchitecture

Parameter variations, which are increasing along with advances in process technologies, affect both timing and power. Variability must be considered at both the circuit and microarchitectural design levels to keep pace with performance scaling and to keep power consumption within reasonable limits. This article presents an overview of the main sources of variability and surveys variation-tolerant circuit and microarchitectural approaches.Peer ReviewedPostprint (published version

High-Performance low-vcc in-order core

Power density grows in new technology nodes, thus requiring Vcc to scale especially in mobile platforms where energy is critical. This paper presents a novel approach to decrease Vcc while keeping operating frequency high. Our mechanism is referred to as immediate read after write (IRAW) avoidance. We propose an implementation of the mechanism for an Intel® SilverthorneTM in-order core. Furthermore, we show that our mechanism can be adapted dynamically to provide the highest performance and lowest energy-delay product (EDP) at each Vcc level. Results show that IRAW avoidance increases operating frequency by 57% at 500mV and 99% at 400mV with negligible area and power overhead (below 1%), which translates into large speedups (48% at 500mV and 90% at 400mV) and EDP reductions (0.61 EDP at 500mV and 0.33 at 400mV).Peer ReviewedPostprint (published version

Energy-efficient processor design using multiple clock domains with dynamic voltage and frequency scaling

Journal ArticleAs clock frequency increases and feature size decreases, clock distribution and wire delays present a growing challenge to the designers of singly-clocked, globally synchronous systems. We describe an alternative approach, which we call a Multiple Clock Domain (MCD) processor in which the chip is divided into several (coarse-grained) clock domains, within which independent voltage and frequency scaling can be performed. Boundaries between domains are chosen to exploit existing queues, thereby minimizing inter-domain synchronization costs. We propose four clock domains, corresponding to the front end (including LI instruction cache), integer units, floating point units, and load-store units (including Ll data cache and L2 cache). We evaluate this design using a simulation infrastructure based on SimpleScalar and Wattch. In an attempt to quantify potential energy savings independent of any particular on-line control strategy, we use of-line analysis of traces from a single-speed run of each of our benchmark applications to identify profitable reconfiguration points for a subsequent dynamic scaling run. Dynamic runs incorporate a detailed model of inter-domain synchronization delays, with latencies for intra-domain scaling similar to the whole-chip scaling latencies of Intel XScale and Transmeta LongRun technologies. Using applications from the MediaBench, Olden, and SPEC2000 benchmark suites, we obtain an average energy-delay product improvement of 20% with MCD compared to a modest 3% savings from voltage scaling a single clock and voltage system

Exceeding Conservative Limits: A Consolidated Analysis on Modern Hardware Margins

Modern large-scale computing systems (data centers, supercomputers, cloud and edge setups and high-end cyber-physical systems) employ heterogeneous architectures that consist of multicore CPUs, general-purpose many-core GPUs, and programmable FPGAs. The effective utilization of these architectures poses several challenges, among which a primary one is power consumption. Voltage reduction is one of the most efficient methods to reduce power consumption of a chip. With the galloping adoption of hardware accelerators (i.e., GPUs and FPGAs) in large datacenters and other large-scale computing infrastructures, a comprehensive evaluation of the safe voltage reduction levels for each different chip can be employed for efficient reduction of the total power. We present a survey of recent studies in voltage margins reduction at the system level for modern CPUs, GPUs and FPGAs. The pessimistic voltage guardbands inserted by the silicon vendors can be exploited in all devices for significant power savings. On average, voltage reduction can reach 12% in multicore CPUs, 20% in manycore GPUs and 39% in FPGAs.Comment: Accepted for publication in IEEE Transactions on Device and Materials Reliabilit