Channel estimation scheme for 3.9G wireless communication systems using RLS algorithm

Main challenges for a terminal implementation are efficient realization of the receiver, especially for channel estimation (CE) and equalization. In this paper, training based recursive least square (RLS) channel estimator technique is presented for a long term evolution (LTE) single carrier-frequency division multiple access (SC-FDMA) wireless communication system. This CE scheme uses adaptive RLS estimator which is able to update parameters of the estimator continuously, so that knowledge of channel and noise statistics are not required. Simulation results show that the RLS CE scheme with 500 Hz Doppler frequency has 3 dB better performances compared with 1.5 kHz Doppler frequency

Peak to average power ratio analysis for LTE systems

The 3rd generation partnership project (3GPP) long term evolution (LTE) standard uses single carrier frequency division multiple access (SCFDMA) scheme for the uplink transmissions and orthogonal frequency division multiplexing access (OFDMA) in downlink. SCFDMA uses DFT spreading prior to OFDMA modulation to map the signal from each user to a subset of the available subcarriers i.e., single carrier modulation. The efficiency of a power amplifier is determined by the peak to average power ratio (PAPR) of the modulated signal. In this paper, we analyze the PAPR in 3GPP LTE systems using root raised cosine based filter. Simulation results show that the SCFDMA subcarrier mapping has a significantly lower PAPR compared to OFDMA. Also comparing the three forms of SCFDMA subcarrier mapping, results show that interleave FDMA (IFDMA) subcarrier mapping with proposed root raised cosine filter reduced PAPR significantly than localized FDMA (LFDMA) and distributed (DFDMA) mapping. This improves its radio frequency (RF) power amplifier efficiency and also the mean power output from a battery driven mobile terminal.<br /

Low complexity MMSE based channel estimation technique for LTE OFDMA systems

Long term evolution (LTE) is designed for high speed data rate, higher spectral efficiency, and lower latency as well as high-capacity voice support. LTE uses single carrierfrequency division multiple access (SC-FDMA) scheme for the uplink transmission and orthogonal frequency division multiple access (OFDMA) in downlink. The one of the most important challenges for a terminal implementation are channel estimation (CE) and equalization. In this paper, a minimum mean square error (MMSE) based channel estimator is proposed for an OFDMA systems that can avoid the ill-conditioned least square (LS) problem with lower computational complexity. This channel estimation technique uses knowledge of channel properties to estimate the unknown channel transfer function at non-pilot subcarriers.<br /

Channel Estimation And Correction Methods For Ofdma Based Lte Downlink System

In present era, cellular communication plays a vital role for communicating over long distance. The number of mobile subscribers is increasing tremendously day by day. 3GPP LTE is the evolution of the UMTS in response to ever-increasing demands for high quality multimedia services according to users\u27 expectations. The average data consumption exceeds hundreds of Megabytes per subscriber per month. To introduce, summarize and get acquainted with this new technology LTE is one of the main objectives of my thesis. The Downlink is always considered an important factor in terms of coverage and capacity aspects in between Downlink and Uplink factors for cellular communication. Orthogonal Frequency Division Multiple Access (OFDMA) and Multiple Input Multiple Output (MIMO) are the new technologies which enhance the performance of the traditional wireless communication experience for downlink. In this thesis, we considered the downlink system for channel estimation by using different algorithms and interpolation methods. Channel Estimation algorithms such as Least Squares Estimation (LSE) and Minimum Mean Square Error (MMSE) have been evaluated for different channel models. The interpolation method used in algorithms is Linear, Piecewise constant, Averaged and Pilot averaged. I measured the performance of these algorithms in terms of Bit Error Rate (BER) and Symbol Error Rate (SER). The results are presented to illustrate the salient concept of the LTE communication system

Low-power Physical-layer Design for LTE Based Very NarrowBand IoT (VNB - IoT) Communication

abstract: With the new age Internet of Things (IoT) revolution, there is a need to connect a wide range of devices with varying throughput and performance requirements. In this thesis, a wireless system is proposed which is targeted towards very low power, delay insensitive IoT applications with low throughput requirements. The low cost receivers for such devices will have very low complexity, consume very less power and hence will run for several years. Long Term Evolution (LTE) is a standard developed and administered by 3rd Generation Partnership Project (3GPP) for high speed wireless communications for mobile devices. As a part of Release 13, another standard called narrowband IoT (NB-IoT) was introduced by 3GPP to serve the needs of IoT applications with low throughput requirements. Working along similar lines, this thesis proposes yet another LTE based solution called very narrowband IoT (VNB-IoT), which further reduces the complexity and power consumption of the user equipment (UE) while maintaining the base station (BS) architecture as defined in NB-IoT. In the downlink operation, the transmitter of the proposed system uses the NB-IoT resource block with each subcarrier modulated with data symbols intended for a different user. On the receiver side, each UE locks to a particular subcarrier frequency instead of the entire resource block and operates as a single carrier receiver. On the uplink, the system uses a single-tone transmission as specified in the NB-IoT standard. Performance of the proposed system is analyzed in an additive white Gaussian noise (AWGN) channel followed by an analysis of the inter carrier interference (ICI). Relationship between the overall filter bandwidth and ICI is established towards the end.Dissertation/ThesisMasters Thesis Electrical Engineering 201

Channel estimation in massive MIMO systems

Last years were characterized by a great demand for high data throughput, good quality and spectral efficiency in wireless communication systems. Consequently, a revolution in cellular networks has been set in motion towards to 5G. Massive multiple-input multiple-output (MIMO) is one of the new concepts in 5G and the idea is to scale up the known MIMO systems in unprecedented proportions, by deploying hundreds of antennas at base stations. Although, perfect channel knowledge is crucial in these systems for user and data stream separation in order to cancel interference. The most common way to estimate the channel is based on pilots. However, problems such as interference and pilot contamination (PC) can arise due to the multiplicity of channels in the wireless link. Therefore, it is crucial to define techniques for channel estimation that together with pilot contamination mitigation allow best system performance and at same time low complexity. This work introduces a low-complexity channel estimation technique based on Zadoff-Chu training sequences. In addition, different approaches were studied towards pilot contamination mitigation and low complexity schemes, with resort to iterative channel estimation methods, semi-blind subspace tracking techniques and matrix inversion substitutes. System performance simulations were performed for the several proposed techniques in order to identify the best tradeoff between complexity, spectral efficiency and system performance