A power and time efficient radio architecture for LDACS1 air-to-ground communication

L-band Digital Aeronautical Communication System (LDACS) is an emerging standard that aims at enhancing air traffic management by transitioning the traditional analog aeronautical communication systems to the superior and highly efficient digital domain. The standard places stringent requirements on the communication channels to allow them to coexist with critical L-band systems, requiring complex processing and filters in baseband. Approaches based on cognitive radio are also proposed since this allows tremendous increase in communication capacity and spectral efficiency. This requires high computational capability in airborne vehicles that can perform the complex filtering and masking, along with tasks associated with cognitive radio systems like spectrum sensing and baseband adaptation, while consuming very less power. This paper proposes a radio architecture based on new generation FPGAs that offers advanced capabilities like partial reconfiguration. The proposed architecture allows non-concurrent baseband modules to be dynamically loaded only when they are required, resulting in improved energy efficiency, without sacrificing performance. We evaluate the case of non-concurrent spectrum sensing logic and transmission filters on our cognitive radio platform based on Xilinx Zynq, and show that our approach results in 28.3% reduction in DSP utilisation leading to lower energy consumption at run-time

Electronic dispersion precompensation of direct-detected NRZ using analog filtering

We demonstrate (in real-time) electrical dispersion compensation in direct detection links using analog transmit side filtering techniques. By this means, we extend the fiber reach using a low complexity solution while avoiding digital preprocessing and digital-to-analog converters (DACs) which are commonly used nowadays. Modulation is done using an IQ MachZehnder modulator (MZM) which allows straightforward compensation of the complex impulse response caused by chromatic dispersion in the fiber. A SiGe BiCMOS 5-tap analog complex finite impulse response (FIR) filter chip and/or a delay between both driving signals of the MZMs is proposed for the filter implementation. Several link experiments are conducted in C-band where transmission up to 60 km of standard single-mode fiber (SSMF) of direct detected 28Gb/s NRZ/OOK is demonstrated. The presented technique can be used in applications where low power consumption is critical

Integrated Transversal Equalizers in High-Speed Fiber-Optic Systems

Intersymbol interference (ISI) caused by intermodal dispersion in multimode fibers is the major limiting factor in the achievable data rate or transmission distance in high-speed multimode fiber-optic links for local area networks applications. Compared with optical-domain and other electrical-domain dispersion compensation methods, equalization with transversal filters based on distributed circuit techniques presents a cost-effective and low-power solution. The design of integrated distributed transversal equalizers is described in detail with focus on delay lines and gain stages. This seven-tap distributed transversal equalizer prototype has been implemented in a commercial 0.18-µm SiGe BiCMOS process for 10-Gb/s multimode fiber-optic links. A seven-tap distributed transversal equalizer reduces the ISI of a 10-Gb/s signal after 800 m of 50-µm multimode fiber from 5 to 1.38 dB, and improves the bit-error rate from about 10^-5 to less than 10^-12

High Performance, Continuously Tunable Microwave Filters using MEMS Devices with Very Large, Controlled, Out-of-Plane Actuation

Software defined radios (SDR) in the microwave X and K bands offer the promise of low cost, programmable operation with real-time frequency agility. However, the real world in which such radios operate requires them to be able to detect nanowatt signals in the vicinity of 100 kW transmitters. This imposes the need for selective RF filters on the front end of the receiver to block the large, out of band RF signals so that the finite dynamic range of the SDR is not overwhelmed and the desired nanowatt signals can be detected and digitally processed. This is currently typically done with a number of narrow band filters that are switched in and out under program control. What is needed is a small, fast, wide tuning range, high Q, low loss filter that can continuously tune over large regions of the microwave spectrum. In this paper we show how extreme throw MEMS actuators can be used to build such filters operating up to 15 GHz and beyond. The key enabling attribute of our MEMS actuators is that they have large, controllable, out-of-plane actuation ranges of a millimeter or more. In a capacitance-post loaded cavity filter geometry, this gives sufficient precisely controllable motion to produce widely tunable devices in the 4-15 GHz regime.Comment: 12 pages 14 figures 2 table

A Scalable Correlator Architecture Based on Modular FPGA Hardware, Reuseable Gateware, and Data Packetization

A new generation of radio telescopes is achieving unprecedented levels of sensitivity and resolution, as well as increased agility and field-of-view, by employing high-performance digital signal processing hardware to phase and correlate large numbers of antennas. The computational demands of these imaging systems scale in proportion to BMN^2, where B is the signal bandwidth, M is the number of independent beams, and N is the number of antennas. The specifications of many new arrays lead to demands in excess of tens of PetaOps per second. To meet this challenge, we have developed a general purpose correlator architecture using standard 10-Gbit Ethernet switches to pass data between flexible hardware modules containing Field Programmable Gate Array (FPGA) chips. These chips are programmed using open-source signal processing libraries we have developed to be flexible, scalable, and chip-independent. This work reduces the time and cost of implementing a wide range of signal processing systems, with correlators foremost among them,and facilitates upgrading to new generations of processing technology. We present several correlator deployments, including a 16-antenna, 200-MHz bandwidth, 4-bit, full Stokes parameter application deployed on the Precision Array for Probing the Epoch of Reionization.Comment: Accepted to Publications of the Astronomy Society of the Pacific. 31 pages. v2: corrected typo, v3: corrected Fig. 1