Reconfigurable Signal Processing and DSP Hardware Generator for 5G Transmitters

To impose the reconfigurability and reusability of digital circuits for millimeterwave transmitter architectures, high-speed digital signal processing architectures are explored. The digital front-end of these next-generation transmitters can be implemented up to the maximum operating frequency to meet the requirements of the 5G NR FR2 frequency bands. This paper presents an efficient implementation of a reconfigurable digital signal processor (DSP) that contains programmable multistage multirate filters, operable up to 4 GHz, and a flexible generator for polar, outphasing, and multilevel outphasing modulation. The system achieves an excellent ACLR of 42 dB and EVM degradation of 1.61% with a 7-bit phase signal at a sampling frequency of 4 GHz for outphasing modulation. Digital synthesis of the circuit in a 22 nm FDSOI process results in a core area of 0.12 mm2and an estimated power consumption of 142 mW for a 200 MHz bandwidth 5G NR baseband signal.acceptedVersionPeer reviewe

Linearity of Outphasing Radio Transmitters

The outphasing transmitter is a promising technique, which can simultaneously achieve high linearity and power efficiency, thereby addressing the major design requirements of next generation transmitters. It employs highly non-linear power amplifier (PA) classes in a linear manner, in principle transmitting a distortion-free signal. Due to symmetric nature of the outphasing architecture, its linearity performance is constrained by any mismatches and non-linear effects encountered in the RF paths. This thesis analyzes the linearity performance of outphasing transmitters (in terms of ACLR specification) for LTE base station applications, under the non-linear effects and tolerances present in practical implementations. The system-level model, built in Matlab software, investigates the important non-linear effects present in outphasing transmitters, including gain and phase imbalance, IQ modulator mismatches, delay imbalance, and the non-linear effects of PAs and Chireix combiners. The path and delay mismatches result in only partial cancellation of the wideband quadrature signal, and thus create interference in both the in-band and out-of-band frequency regions. The misalignment in IQ modulators, such as gain/phase imbalance and carrier leakage, introduces amplitude and phase modulation in the outphased signals. The quadrature modulator mismatches, in conjunction with amplifier nonlinearity, result in spectral regrowth around the carrier frequency. The transmitter linearity performance is also affected by mismatches in the non-linear characteristics of the PAs. Realistic square-wave signals, exhibiting finite rise- and fall- time, also create spectral leakage for distinct rise/fall times in each outphasing branch. Furthermore, the Chireix combiner severely degrades the linearity of outphasing transmitters; it produces ACLR well below the specified limit for LTE base stations. This makes mandatory the compensation of Chireix combiner induced non-linearity in outphasing transmitters. The strict linearity requirements (for LTE downlink applications) present a small tolerance window for mismatches experienced in practical circuits. The relatively small tolerance margin indicates the need of linearization and compensation techniques in outphasing transmitters

Techniques for Wideband All Digital Polar Transmission

abstract: Modern Communication systems are progressively moving towards all-digital transmitters (ADTs) due to their high efficiency and potentially large frequency range. While significant work has been done on individual blocks within the ADT, there are few to no full systems designs at this point in time. The goal of this work is to provide a set of multiple novel block architectures which will allow for greater cohesion between the various ADT blocks. Furthermore, the design of these architectures are expected to focus on the practicalities of system design, such as regulatory compliance, which here to date has largely been neglected by the academic community. Amongst these techniques are a novel upconverted phase modulation, polyphase harmonic cancellation, and process voltage and temperature (PVT) invariant Delta Sigma phase interpolation. It will be shown in this work that the implementation of the aforementioned architectures allows ADTs to be designed with state of the art size, power, and accuracy levels, all while maintaining PVT insensitivity. Due to the significant performance enhancement over previously published works, this work presents the first feasible ADT architecture suitable for widespread commercial deployment.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Analysis and design of ΣΔ Modulators for Radio Frequency Switchmode Power Amplifiers

Power amplifiers are an integral part of every basestation, macrocell, microcell and mobile phone, enabling data to be sent over the distances needed to reach the receiver’s antenna. While linear operation is needed for transmitting WCDMA and OFDM signals, linear operation of a power amplifier is characterized by low power efficiency, and contributes to unwanted power dissipation in a transmitter. Recently, a switchmode power amplifier operation was considered for reducing power losses in a RF transmitter. A linear and efficient operation of a PA can be achieved when the transmitted RF signal is ΣΔ modu- lated, and subsequently amplified by a nonlinear device. Although in theory this approach offers linearity and efficiency reaching 100%, the use of ΣΔ modulation for transmitting wideband signals causes problems in practical implementation: it requires high sampling rate by the digital hardware, which is needed for shaping large contents of a quantization noise induced by the modulator but also, the binary output from the modulator needs an RF power amplifier operating over very wide frequency band. This thesis addresses the problem of noise shaping in a ΣΔ modulator and nonlinear distortion caused by broadband operation in switchmode power amplifier driven by a ΣΔ modulated waveform. The problem of sampling rate increase in a ΣΔ modulator is solved by optimizing structure of the modulator, and subsequent processing of an input signal’s samples in parallel. Independent from the above, a novel technique for reducing quan- tization noise in a bandpass ΣΔ modulator using single bit quantizer is presented. The technique combines error pulse shaping and 3-level quantization for improving signal to noise ratio in a 2-level output. The improvement is achieved without the increase of a digital hardware’s sampling rate, which is advantageous also from the perspective of power consumption. The new method is explored in the course of analysis, and verified by simulated and experimental results. The process of RF signal conversion from the Cartesian to polar form is analyzed, and a signal modulator for a polar transmitter with a ΣΔ-digitized envelope signal is designed and implemented. The new modulator takes an advantage of bandpass digital to analog conversion for simplifying the analog part of the modulator. A deformation of the pulsed RF signal in the experimental modulator is demonstrated to have an effect primarily on amplitude of the RF signal, which is correctable with simple predistortion

Concurrent Multi-Band Envelope Tracking Power Amplifiers for Emerging Wireless Communications

Emerging wireless communication is shifting toward data-centric broadband services, resulting in employment of sophisticated and spectrum efficient modulation and access techniques. This yields communication signals with large peak-to-average power ratios (PAPR) and stringent linearity requirements. For example, future wireless communication standard, such as long term evolution advanced (LTE-A) require adoption of carrier aggregation techniques to improve their effective modulation bandwidth. The carrier aggregation technique for LTE-A incorporates multiple carriers over a wide frequency range to create a wider bandwidth of up to 100MHz. This will require future power amplifiers (PAs) and transmitters to efficiently amplify concurrent multi-band signals with large PAPR, while maintaining good linearity. Different back-off efficiency enhancement techniques are available, such as envelope tracking (ET) and Doherty. ET has gained a lot of attention recently as it can be applied to both base station and mobile transmitters. Unfortunately, few publications have investigated concurrent multi-band amplification using ET PAs, mainly due to the limited bandwidth of the envelope amplifier. In this thesis, a novel approach to enable concurrent amplification of multi-band signals using a single ET PA will be presented. This thesis begins by studying the sources of nonlinearities in single-band and dual-band PAs. Based on the analysis, a design methodology is proposed to reduce the sources of memory effects in single-band and dual-band PAs from the circuit design stage and improve their linearizability. Using the proposed design methodology, a 45W GaN PA was designed. The PA was linearized using easy to implement, memoryless digital pre-distortion (DPD) with 8 and 28 coefficients when driven with single-band and dual-band signals, respectively. This analysis and design methodology will enable the design of PAs with reduced memory effects, which can be linearized using simple, power efficient linearization techniques, such as lookup table or memoryless polynomial DPD. Note that the power dissipation of the linearization engine becomes crucial as we move toward smaller base station cells, such as femto- and pico-cells, where complicated DPD models cannot be implemented due to their significant power overhead. This analysis is also very important when implementing a multi-band ET PA system, where the sources of memory effects in the PA itself are minimized through the proposed design methodology. Next, the principle of concurrent dual-band ET operation using the low frequency component (LFC) of the envelope of the dual-band signal is presented. The proposed dual-band ET PA modulates the drain voltage of the PA using the LFC of the envelope of the dual-band signal. This will enable concurrent dual-band operation of the ET PA without posing extra bandwidth requirements on the envelope amplifier. A detailed efficiency and linearity analysis of the dual-band ET PA is also presented. Furthermore, a new dual-band DPD model with supply dependency is proposed in this thesis, capable of capturing and compensating for the sources of distortion in the dual-band ET PA. To the best of our knowledge, concurrent dual-band operation of ET PAs using the LFC of the envelope of the dual-band signal is presented for the first time in the literature. The proposed dual-band ET operation is validated using the measurement results of two GaN ET PA prototypes. Lastly, the principle of concurrent dual-band ET operation is extended to multi-band signals using the LFC of the envelope of the multi-band signal. The proposed multi-band ET operation is validated using the measurement results of a tri-band ET PA. To the best of our knowledge, this is the first reported tri-band ET PA in literature. The tri-band ET PA is linearized using a new tri-band DPD model with supply dependency

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

Supply modulated GaN HEMT power amplifiers - From transistor to system

Power amplifiers (PAs) for mobile communication applications are required to fulfil stringent requirements concerning linearity while keeping a high efficiency over a wide power range and bandwidth. To achieve this, a number of advanced PA topologies have been developed, mostly based on either load modulation, such as Doherty PAs or load modulation balanced PAs, or on supply modulation such as envelope tracking or envelope elimination and restoration. Supply modulation has an advantage over other topologies as the power range of high efficiency can be realised over arbitrary bandwidths, only limited by the bandwidth of the PA. This does, however, come at the cost of a significantly more complicated voltage supply. Instead of a static supply voltage, the PA needs to be provided with one which is rapidly changing, requiring a supply modulator capable of powering the PA while modulating its supply voltage. This thesis investigates a number of challenges in supply modulated power amplifiers, ranging from the transistor itself to circuit design and system level considerations and focusses on power levels up to 10 W and frequencies between 1 GHz and 4 GHz. Transistors, as the centre-piece of a PA, determine how well the PA reacts to a changing supply voltage. In this work, the traits that make GaN HEMTs suitable for supply modulated PAs were investigated, and gain variation with changing supply voltage was established as an important parameter. This gain variation is described in detail and its impacts on PA performance are discussed. By comparing transistors in literature, gain variation has been demonstrated to be a prevalent characteristic in transistors with GaN HEMTs showing a very wide range of gain variation. Using a small-signal model based on measurements, the voltage dependent behaviour of the feedback capacitance CGD is, for the first time, identified as the origin of small-signal gain variation. This is traced down to the gate field plate which is commonly used to combat surface trapping effects in GaN HEMTs. With this in mind, two different ways of changing the transistor geometry to reduce the impact of gain variation and thus optimise the transistor for operation in supply modulated PAs are discussed and demonstrated using a 250 nm GaN HEMT. As a result of the non-linearity of the feedback and gate-source capacitances, the input impedance of GaN HEMTs changes with supply voltage and drive power. This prevents the transistor from being matched at all supply voltages and input powers and introduces phase distortion. Using simulation and measurement, the impact of input impedance on linearity and efficiency of supply modulated power amplifiers is demonstrated on a 2.9 GHz 10 W PA. Careful selection of the input impedance allows improvement of AM/PM distortion of a supply modulated PA with little cost in terms of AM/AM and PAE. I Supply modulators have a significant impact on efficiency and linearity of the ET system. One supply modulator topology with the potential to generate a supply voltage with a high modulation bandwidth is the RF modulator in which the input DC voltage is turned into an RF signal and rectified, resulting in an output voltage which depends on the excitation of the PA. While PAs are well understood in every detail, there are gaps in the understanding of RF rectifiers. Using active load-pull/source-pull measurements, intrinsic gate and drain waveforms of a GaN HEMT operated as a rectifier are demonstrated for the first time. This allows in-detail evaluation of the impact of the gate termination in self-synchronous rectifiers. It also allows detailed analysis of the loss mechanisms in rectifiers and formulation of the required impedances to realise efficient self-synchronous operation, resulting in efficiencies exceeding 90% over wide power ranges. Using waveform engineering, a new type of RF modulator, with potentially very high bandwidths, based on even harmonic generation/injection is proposed. The necessary operating conditions of the rectifier part of the modulator are emulated using an active load-pull/source-pull system to successfully demonstrate that the rectifier behaves as predicted. Using a simple demonstrator, preliminary measurements were conducted and the RF modulator was shown to work, reaching efficiencies up to 78%. As PA and supply modulator are combined, they present impedances to each other. These impedances have a significant impact on the behaviour of both sub-systems. A simple way to characterise both the impedance presented to the PA by the modulator and the impedance presented to the modulator by the PA is described. Using a state-of-the-art modulator, these impedances are measured, the modulator impedance is demonstrated to be close to the simulated value. These measurements also demonstrate that the impedances change significantly with the operating conditions