The Class-E/F Family of ZVS Switching Amplifiers

A new family of switching amplifiers, each member having some of the features of both class E and inverse F, is introduced. These class-E/F amplifiers have class-E features such as incorporation of the transistor parasitic capacitance into the circuit, exact truly switching time-domain solutions, and allowance for zero-voltage-switching operation. Additionally, some number of harmonics may be tuned in the fashion of inverse class F in order to achieve more desirable voltage and current waveforms for improved performance. Operational waveforms for several implementations are presented, and efficiency estimates are compared to class-E

Fully equipped half bridge building block for fast prototyping of switching power converters

P

A 6.0-mW 10.0-Gb/s Receiver With Switched-Capacitor Summation DFE

A low-power receiver with a one-tap decision feedback equalization (DFE) was fabricated in 90-nm CMOS technology. The speculative equalization is performed using switched-capacitor-based addition at the front-end sample-hold circuit. In order to further reduce the power consumption, an analog multiplexer is used in the speculation technique implementation. A quarter-rate-clocking scheme facilitates the use of low-power front-end circuitry and CMOS clock buffers. The receiver was tested over channels with different levels of ISI. The signaling rate with BER<10^-12 was significantly increased with the use of DFE for short- to medium-distance PCB traces. At 10-Gb/s data rate, the receiver consumes less than 6.0 mW from a 1.0-V supply. This includes the power consumed in all quarter-rate clock buffers, but not the power of a clock recovery loop. The input clock phase and the DFE taps are adjusted externally

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Transformer based front-end for a low power 2.4 GHz transceiver

A low power transceiver architecture for the 2.4 GHz ISM band using a 1.0 V supply is presented. It employs a transformer to convert the 100 Ω antenna impedance to almost 1 kΩ and so facilitates a low power transmitter and receiver. The simulated post-layout output power of the differential class-E power amplifier is 2.0 dBm with a drain efficiency of 28.4%. The direct-conversion receiver achieves a very low power consumption of 420 μW and a noise figure of 15.0 dB.Ministerio de Ciencia e Innovación TEC2009-08447Junta de Andalucía TIC-0281

A 10-bit Charge-Redistribution ADC Consuming 1.9 μW at 1 MS/s

This paper presents a 10 bit successive approximation ADC in 65 nm CMOS that benefits from technology scaling. It meets extremely low power requirements by using a charge-redistribution DAC that uses step-wise charging, a dynamic two-stage comparator and a delay-line-based controller. The ADC requires no external reference current and uses only one external supply voltage of 1.0 V to 1.3 V. Its supply current is proportional to the sample rate (only dynamic power consumption). The ADC uses a chip area of approximately 115--225 μm2. At a sample rate of 1 MS/s and a supply voltage of 1.0 V, the 10 bit ADC consumes 1.9 μW and achieves an energy efficiency of 4.4 fJ/conversion-step