Design consideration in low dropout voltage regulator for batteryless power management unit

Harvesting energy from ambient Radio Frequency (RF) source is a great deal toward batteryless Internet of Thing (IoT) System on Chip (SoC) application as green technology has become a future interest. However, the harvested energy is unregulated thus it is highly susceptible to noise and cannot be used efficiently. Therefore, a dedicated low noise and high Power Supply Ripple Rejection (PSRR) of Low Dropout (LDO) voltage regulator are needed in the later stages of system development to supply the desired load voltage. Detailed analysis of the noise and PSRR of an LDO is not sufficient. This work presents a design of LDO to generate a regulated output voltage of 1.8V from 3.3V input supply targeted for 120mA load application. The performance of LDO is evaluated and analyzed. The PSRR and noise in LDO have been investigated by applying a low-pass filter. The proposed design achieves the design specification through the simulation results by obtaining 90.85dB of open-loop gain, 76.39º of phase margin and 63.46dB of PSRR respectively. The post-layout simulation shows degradation of gain and maximum load current due to parasitic issue. The measurement of maximum load regulation is dropped to 96mA compared 140mA from post-layout. The proposed LDO is designed using 180nm Silterra CMOS process technology

Design of low-dropout regulator for ultra low power on-chip applications

Low Drop Out (LDO) voltage regulators are commonly used to supply low-voltage digital circuits such as microprocessor cores. These digital circuits normally are continuously changing from one mode of operation to another. Therefore, the load demand can change rapidly resulting in large voltage transients at the output of the regulator which can adversely affect the digital circuitry. In this Master's Thesis, design topologies and challenges of very low-power fully integrated On-Chip Low-Dropout (LDO) regulators have been analyzed. Instead of conventional LDO which makes use of a large external capacitor to have better dynamic response and stability, a CapacitorLess LDO (CL-LDO) is chosen on considerations of smaller area. The most challenging part of designing this kind of regulator is achieving high current efficiency by reducing the quiescent current while ensuring good stability response as well as good regulation performance. Thus, different circuit techniques must be carefully added in order to balance the lack of the large external capacitor having the minimum impact on system efficiency. This work focuses on designing a fully integrated low-dropout regulator with good dynamic performance, high regulation performance and ultra-low power consumption. The stability is achieved by the use of two pole-splitting techniques, namely Cascode and Nested-Miller compensation. The good dynamic response with low quiescent current are achieved by the use of an adaptive biasing circuit, a gm-boost circuit and adaptive power transistor architecture

Voltage and Time-Domain Analog Circuit Techniques for Scaled CMOS Technologies

CMOS technology scaling has resulted in reduced supply voltage and intrinsic voltage gain of the transistor. This presents challenges to the analog circuit designers due to lower signal swing and achievable signal to noise ratio (SNR), leading to increased power consumption. At the same time, device speed has increased in lower design nodes, which has not been directly beneficial for analog circuit design. This thesis presents voltage-domain and time-domain circuit scaling friendly circuit architectures that minimize the power consumption and benefit from the increasing transistor speeds. In the voltage-domain, an on-the-fly gain selection block is demonstrated as an alternative to the traditional MDAC architecture to enhance the input dynamic range of a medium-resolution medium-speed analog-to-digital converter (ADC) at reduced supply voltages. The proposed design also eliminates the need for a reference buffer, thus providing power savings. The measured prototype enhances the input dynamic range of a 12bit, 40MSPS ADC to 80.6dB at 1.2V supply voltage. In the time-domain, a generic circuit design approach is presented, followed by an in-depth analysis of Voltage-Controlled-Oscillator based Operational Transconductance Amplifiers (VCO-OTAs). A discrete-time-domain small-signal model based on the zero crossings of the internal VCOs is developed to predict the stability, the step response, and the frequency response of the circuit when placed in feedback. The model accurately predicts the circuit behavior for an arbitrary input frequency, even as the VCO free-running frequency approaches the unity-gain bandwidth of the closed-loop system, where other intuitive small-signal models available in the literature fail. Next, we present an application of VCO-OTA in designing a baseband trans-impedance amplifier (TIA) for current-mode receivers as a scaling-friendly and power-efficient alternative to the inverter-based OTA. We illustrate a design methodology for the choice of the VCO-OTA parameters in the context of a receiver design with an example of a 20MHz RF-channel-bandwidth receiver operating at 2GHz. Receiver simulation results demonstrate an improvement of up to 12dB in blocker 1dB compression point (B1dB) for slightly higher power consumption or up to 2.6x power reduction of the TIA resulting in up to 2x power reduction of the receiver for similar B1dB performance. Next, we present some examples of VCO-OTAs. We first illustrate the benefit of a VCO-OTA in a low-dropout-voltage regulator to achieve a dropout voltage of only100mV and operating down to 0.8V input supply, compared to the prototype based on traditional OTA with a minimum dropout voltage of 150mV, operating at a minimum of 1.2V supply. Both the capacitor-less prototypes can drive up to 1nF load capacitor and provide a current of 60mA. The next prototype showcases a method to reduce the power consumption of a VCO-OTA and spurs at the VCO frequency, with an application in the design of a fourth-order Butterworth filter at 4MHz. The thesis concludes with a design example of 0.2V VCO-OTA