Low-Leakage ESD Power Supply Clamps in General Purpose 65 nm CMOS Technology

Electrostatic discharge (ESD) is a well-known contributor that reduces the reliability and yield of the integrated circuits (ICs). As ICs become more complex, they are increasingly susceptible to such failures due to the scaling of physical dimensions of devices and interconnect on a chip [1]. These failures are caused by excessive electric field and/or excessive current densities and result in the dielectric breakdown, electromigration of metal lines and contacts. ESD can affect the IC in its different life stages, from wafer fabrication process to failure in the field. Furthermore, ESD events can damage the integrated circuit permanently (hard failure), or cause a latent damage (soft failure) [2]. ESD protection circuits consisting of I/O protection and ESD power supply clamps are routinely used in ICs to protect them against ESD damage. The main objective of the ESD protection circuit is to provide a low-resistive discharge path between any two pins of the chip to harmlessly discharge ESD energy without damaging the sensitive circuits. The main target of this thesis is to design ESD power supply clamps that have the lowest possible leakage current without degrading the ESD protection ability in general purpose TSMC 65 nm CMOS technology. ESD clamps should have a very low-leakage current and should be stable and immune to the power supply noise under the normal operating conditions of the circuit core. Also, the ESD clamps must be able to handle high currents under an ESD event. All designs published in the general purpose 65 nm CMOS technology have used the SCR as the clamping element since the SCR has a higher current carrying capability compared to an MOS transistor of the same area [3]. The ESD power supply clamp should provide a low-resistive path in both directions to be able to deal with both PSD and NDS zapping modes. The SCR based design does not provide the best ESD protection for the NDS zapping mode (positive ESD stress at VSS with grounded VDD node) since it has two parasitic resistances (RNwell and RPsub) and one parasitic diode (the collector to base junction diode of the PNP transistor) in the path from the VSS to VDD. Furthermore, SCR-based designs are not suitable for application that exposed to hot switching or ionizing radiation [2]. In GP process, the gate oxide thickness of core transistors is reduced compared with LP process counterpart to achieve higher performance designs for high-frequency applications using 1 V core transistors and 2.5 V I/O option. The thinner gate oxide layer results in higher leakage current due to gate tunneling [4]. Therefore, using large thin oxide MOS transistors as clamping elements will result in a huge leakage. In this thesis, four power supply ESD clamps are proposed in which thick oxide MOS transistors are used as the main clamping element. Therefore, the low-leakage current feature is achieved without significantly degrading the ESD performance. In addition, the parasitic diode of the MOS transistors provides the protection against NSD-mode. In this thesis, two different ESD power supply clamp architectures are proposed: standalone ESD power supply clamps and hybrid ESD power supply clamps. Two standalone clamps are proposed: a transient PMOS based ESD clamp with thyristor delay element (PTC), and a static diode triggered power supply (DTC). The standalone clamps were designed to protect the circuit core against ±125 V CDM stress by limiting the voltage between the two power rails to less than the oxide breakdown voltage of the core transistors, BVOXESD = 5 V. The large area of this architecture was the price for maintaining the low-leakage current and an adequate ESD protection. The hybrid clamp architecture was proposed to provide a higher ESD protection, against ±300 V CDM stress, while reducing the layout area and maintaining the low-leakage feature. In the hybrid clamp structure, two clamps are connected in parallel between the two power supply rails, a static clamp, and a transient clamp. The static clamp triggers first and starts to sink the ESD energy and then an RC network triggers the primary transient clamp to sink most of the ESD stress. Two hybrid designs were proposed: PMOS ESD power supply clamp with thyristor delay element and diodes (PTDC), and NMOS ESD power supply clamp with level shifter delay element and diode (NLDC). Simulation results show that the proposed clamps are capable of protecting the circuit core against ±1.5 kV HBM and at least against ±125 V CDM stresses. The measurement results show that all of the proposed clamps are immune against false triggering, and transient induced latch-up. Furthermore, all four designs have responded favorably to the 4 V ESD-like pulse voltage under both chip powered and not powered conditions and after the stress ends the designs turned off. Finally, TLP measurement results show that all four proposed designs meet the minimum design requirement of the ESD protection circuit in the 65 nm CMOS technology (i.e. HBM protection level of ±1.5 kV )

Design, Simulation and Characterization of Novel Electrostatic Discharge Protection Devices and Circuits in Advanced Silicon Technologies

Electrostatic Discharge (ESD) has been one of the major reliability concerns in the advanced silicon technologies and it becomes more important with technology scaling. It has been reported that more than 35% of the failures in integrated circuits (ICs) are ESD induced. ESD event is a phenomenon that a finite amount of charges transfer between two objects with different potential in a quite short time. Such event contains a large energy and the ICs without proper ESD protection could be destroyed easily, so ESD protection solutions are essential to semiconductor industry. ESD protection design consists of on-chip and off-chip ESD protection design, and the research works in this dissertation are all conducted in on-chip level, which incorporate the ESD protection devices and circuits into the microchip, to provide with basic ESD protection from manufacturing to customer use. The basic idea of ESD protection design is to provide a path with low impedance which directs most of the ESD current to flow through itself instead of the core circuit, and the ESD protection path must be robust enough to make sure that it does not fail before the core circuit. In this way, proper design on protection devices and circuits should be considered carefully. To assist the understanding and design of ESD protection, the ESD event in real world has been classified into a few ESD model including Human Body Model (HBM), Machine Model (MM), Charged Device Model (CDM), etc. Some mainstream testing method and industry standard are also introduced, including Transmission Line Pulse (TLP), and IEC 61000-4-2. ESD protection devices including diode, Gate-Grounded N-type MOSFET (GGNMOS), Silicon Controlled Rectifier (SCR) are basic elements for ESD protection design. In this dissertation, the device characteristics in ESD event and their applications are introduced. From the perspective of the whole chip ESD protection design, the concept of circuit level ESD protection and the ESD clamps are also briefly introduced. Technology Computer Aided Design (TCAD) and Simulation Program with Integrated Circuit Emphasis (SPICE) simulation is widely used in ESD protection design. In this dissertation, TCAD and SPICE simulation are carried out for a few times for both of pre-tapeout evaluation on characteristics of the proposed device and circuit and post-tapeout analysis on structure operating mechanism. Automotive electronics has been a popular subject in semiconductor industry, and due to the special requirement of the automotive applications like the capacitive pins, the ESD protection device used in such applications need to be specially designed. In this dissertation, a few SCRs without snapback are discussed in detail. To avoid core circuit damages caused the displacement current induced by the large snapback in conventional SCR, an eliminated/minimized snapback is preferred in a selection of the protection device. Two novel SCRs are proposed for High Voltage (HV), Medium Voltage (MV), and Low Voltage (LV) automotive ESD protection. The typical operating temperature for ICs is up to 125°C, however in automotive applications, the operating temperature may extend up to 850°C. In this way, the characteristics of the ESD protection device under the elevated temperatures will be an essential part to investigate for automotive ESD protection design. In this dissertation, the high temperature characteristics of ESD protection devices including diode and a few SCRs is measured and discussed in detail. TCAD simulation are also conducted to explain the underlying physical mechanism. This work provides with a useful insight and information to ESD protection design in high temperature applications. Besides the high temperature environment, ESD protection are also highly needed for electronics working in other extreme environment like the space. Space is an environment that contains kinds of radiation source and at the same time can generate abundant ESD. The ESD adhering to the space systems could be a potential threat to the space electronics. At the same time, the characteristics of the ESD protection part especially the basic protection device used in the space electronics could be influenced after the irradiation in the space. Therefore, the investigation of the radiation effects on ESD protection devices are necessary. In this dissertation, the total ionizing dose (TID) effects on ESD protection devices are investigated. The devices are irradiated with 1.5 MeV He+ and characterized with TLP tester. The pre- and post-irradiation characteristics are compared and the variation on key ESD parameters are analyzed and discussed. This work offers a useful insight on ESD devices\u27 operation under TID and help with the device designing on ESD protection devices for space electronics. Single ESD protection devices are essential part constructing the ESD protection network, however the optimization on ESD clamp circuit design is also important on building an efficient whole chip ESD protection network. In this dissertation, the design and simulation of a novel voltage triggered ESD detection circuit are introduced. The voltage triggered ESD detection circuit is proposed in a 0.18 um CMOS technology. Comparing with the conventional RC based detection circuit, the proposed circuit realizes a higher triggering efficiency with a much smaller footprint, and is immune to false triggering under fast power-up events. The proposed circuit has a better sensitivity to ESD event and is more reliable in ESD protection applications. The leakage current has been a concern with the scaling down of the thickness of the gate oxide. Therefore, a proper design of the ESD clamp for power rail ESD protection need to be specially considered. In this dissertation, a design of a novel ESD clamp with low leakage current is analyzed. The proposed clamp realized a pretty low leakage current up to 12 nA, and has a smaller footprint than conventional design. It also has a long hold-on time under ESD event and a quick turn-off mechanism for false triggering. SPICE simulation is carried out to evaluate the operation of the proposed ESD clamp

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Advances in Solid State Circuit Technologies

This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields

NASA Tech Briefs, September 1995

A special focus for this issue is Sensors. Topics covered include : Electronic Components and Circuits; Electronic Systems; Physical Sciences; Materials; Life Sciences; Mechanics; Machinery; Fabrication Technology; and Mathematics and Information Sciences. A section of Laser Tech Briefs is included