Angle Control of a Pneumatically Driven Musculoskeletal Model Based on Coordination of Agonist-Antagonist Muscle

In recent years, researchers have been actively pursuing research into developing robots that can be useful in many fields of industry (e.g., service, medical, and aging care). Such robots must be safe and flexible so that they can coexist with people. Pneumatic actuators are useful for achieving this goal because they are lightweight units with natural compliance. Our research focuses on joint angle control for a pneumatically driven musculoskeletal model. In such a model, we use a one-degree-of-freedom joint model and a five-fingered robot hand as test beds. These models are driven by low pressure-driven pneumatic actuators, and mimic the mechanism of the human hand and musculoskeletal structure, which has an antagonistic muscle pair for each joint. We demonstrated a biologically inspired control method using the parameters antagonistic muscle ratio and antagonistic muscle activity. The concept of the method is based on coordination of an antagonistic muscle pair using these parameters. We have investigated the validity of the proposed method both theoretically and experimentally, developed a feedback control system, and conducted joint angle control by implementing the test beds.ArticleJournal of Mechanics Engineering and Automation. 2(12):709-719 (2012)journal articl

Remote-controlled ambidextrous robot hand actuated by pneumatic muscles: from feasibility study to design and control algorithms

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University LondonThis thesis relates to the development of the Ambidextrous Robot Hand engineered in Brunel University. Assigned to a robotic hand, the ambidextrous feature means that two different behaviours are accessible from a single robot hand, because of its fingers architecture which permits them to bend in both ways. On one hand, the robotic device can therefore behave as a right hand whereas, on another hand, it can behave as a left hand. The main contribution of this project is its ambidextrous feature, totally unique in robotics area. Moreover, the Ambidextrous Robot Hand is actuated by pneumatic artificial muscles (PAMs), which are not commonly used to drive robot hands. The type of the actuators consequently adds more originality to the project. The primary challenge is to reach an ambidextrous behaviour using PAMs designed to actuate non-ambidextrous robot hands. Thus, a feasibility study is carried out for this purpose. Investigating a number of mechanical possibilities, an ambidextrous design is reached with features almost identical for its right and left sides. A testbench is thereafter designed to investigate this possibility even further to design ambidextrous fingers using 3D printing and an asymmetrical tendons routing engineered to reduce the number of actuators. The Ambidextrous Robot Hand is connected to a remote control interface accessible from its website, which provides video streaming as feedback, to be eventually used as an online rehabilitation device. The secondary main challenge is to implement control algorithms on a robot hand with a range twice larger than others, with an asymmetrical tendons routing and actuated by nonlinear actuators. A number of control algorithms are therefore investigated to interact with the angular displacement of the fingers and the grasping abilities of the hand. Several solutions are found out, notably the implementations of a phasing plane switch control and a sliding-mode control, both specific to the architecture of the Ambidextrous Robot Hand. The implementation of these two algorithms on a robotic hand actuated by PAMs is almost as innovative as the ambidextrous design of the mechanical structure itself

Design and fabrication of a modularized humanoid arm with pneumatic artificial muscles

Capstone Project submitted to the Department of Engineering, Ashesi University in partial fulfillment of the requirements for the award of Bachelor of Science degree in Mechanical Engineering, May 2021With increase investment in the development of humanoids, there offers a window of opportunity to leverage the rapidly growing market of soft robotics in our strides towards more accurate biomimetic motion and study of humanoids and their applicatory areas. This project encompasses the systematic design, implementation and testing of a lightweight low-cost humanoid arm that utilizes Pneumatic Artificial Muscles (PAM). These muscles do not only exhibit twistable and bendable human-like muscle contractions but modularized in design to stand as a complete controllable unit which may be dissociated and mountable on a support frame on its own. This project achieves the design of a mobile arm unit with total weight of less than 2kg of which is distributed with one-third the weight being borne on the arm. The realized powerto- weight ratio of near 5W per kilogram, under an approximate 13.5 litre per minute rate of pressurization is of desired muscle force, and flex speeds. The McKibben tubing choice of PAM is experimentally validated under a linear fit for its force-contraction performance. This design makes considerable strides in cutting down weight, leveraging power, and being much cheaper than existing solutions. Comparable lightweight arm designs of which some are commercially available have weights of 38kg (Mitsubishi PA10arm), 14kg (KUKA lightweight arm), etc., with power-to-weight ratios of near 1W/kg. However, this project designs cuts down these weights drastically to about 2kg (without any sensory unit yet) and more than doubles the power to weight ratios mentioned.Ashesi Universit

Design and Control of the McKibben Artificial Muscles Actuated Humanoid Manipulator

The McKibben Pneumatic Artificial Muscles (PAMs) are expected to endow the advanced robots with the ability of coexisting and cooperating with humans. However, the application of PAMs is still severely hindered by some critical issues. Focusing on the bionic design issue, this chapter in detail presents the design of a 7-degree-of-freedom (DOF) human-arm-like manipulator. It takes the antagonized PAMs and Bowden cables to mimic the muscle-tendon-ligament structure of human arm by elaborately configuring the DOFs and flexibly deploying the routing of Bowden cables; as a result, the DOFs of the analog shoulder, elbow, and wrist of the robotic arm intersect at a point respectively and the motion of these DOFs is independent from each other for convenience of human-like motion. The model imprecision caused by the strong nonlinearity is universally acknowledged as a main drawback of the PAM systems. Focusing on this issue, this chapter views the model imprecision as an internal disturbance, and presents an approach that observe these disturbances with extended-state-observer (ESO) and compensate them with full-order-sliding-mode-controller (fSMC), via experiments validated the human-like motion performance with expected robustness and tracking accuracy. Finally, some variants of PAMs for remedying the drawbacks of the PAM systems are discussed

The design, analysis and evaluation of a humanoid robotic head

Where robots interact directly with humans on a ‘one-to-one’ basis, it is often quite important for them to be emotionally acceptable, hence the growing interesting in humanoid robots. In some applications it is important that these robots do not just resemble a human being in appearance, but also move like a human being too, to make them emotionally acceptable – hence the interest in biomimetic humanoid robotics. The research described in this thesis is concerned with the design, analysis and evaluation of a biomimetic humanoid robotic head. It is biomimetic in terms of physical design - which is based around a simulated cervical spine, and actuation, which is achieved using pneumatic air muscles (PAMS). The primary purpose of the research, however, and the main original contribution, was to create a humanoid robotic head capable of mimicking complex non-purely rotational human head movements. These include a sliding front-to-back, lateral movement, and a sliding, side-to-side lateral movement. A number of different approaches were considered and evaluated, before finalising the design. As there are no generally accepted metrics in the literature regarding the full range of human head movements, the best benchmarks for comparison are the angular ranges and speeds of humans in terms on pitch (nod), roll (tilt) and yaw (rotate) were used for comparison, and these they were considered desired ranges for the robot. These measured up well in comparison in terms of angular speed and some aspects of range of human necks. Additionally, the lateral movements were measured during the nod, tilt and rotate movements, and established the ability of the robot to perform the complex lateral movements seen in humans, thus proving the benefits of the cervical spine approach. Finally, the emotional acceptance of the robot movements was evaluated against another (commercially made) robot and a human. This was a blind test, in that the (human) evaluators had no way of knowing whether they were evaluation a human or a robot. The tests demonstrated that on scales of Fake/Natural, Machinelike/Humanlike and Unconcsious/Conscious the robot the robot scored similarly to the human

Manos Robóticas Antropomórficas: una revisión

This paper presents a review on main topic regarding to anthropomorphic robotic hands developed in the last years, taking into account the more important mechatronics designs submit on the literature, and making a comparison between them. The next chapters deepen on level of anthropomorphism and dexterity in advanced actuated hands and upper limbs prostheses, as well as a brief overview on issues such as grasping, transmission mechanisms, sensory and actuator system, and also a short introduction on under-actuated robotic hands is reported.Este artículo presenta una revisión de los principales desarrollos que se han hecho en los últimos años en manos robóticas antropomórficas. Las primeras secciones tratan temas como el grado de antropomorfismo y de destreza en las manos robóticas más avanzadas, incluyendo una comparación entre ellas. También se abordan temas como la capacidad de agarre de los efectores finales, los mecanismos de trasmisión, el sistema actuador y sensórico, así como una breve introducción al tema de manos robóticas sub-actuadas. Dirección de correspondencia: Carrera 11 # 101-80, Bogotá (Colombia)

A Study on Active/Passive Pneumatic Actuators for Assistive Systems

The need for intelligent assistive devices is growing. Due to advances in medicine, people are living longer and able to recover from severe neurological incidents, resulting in an increased population with neuromuscular weakness. In workplaces such as assembly lines, there is a high possibility of work-related fatigue or injury, such as when workers squat down or lift their arms during their work tasks. Assistive devices could help remedy loss of strength on their extremities as well as keep the work environment safe and productive, allowing these growing segments of the population in need of the devices to live more self-sufficient, productive, and higher-quality lives.In the design of assistive systems, an important design goal is prolonged operational time, which requires the minimum usage of energy. Energy consumption can be reduced by modifying the mechanical characteristics of assistive systems according to the dynamic characteristics of the human body, which vary considerably between tasks. This dissertation investigates 1) the design of actuators with adjustable mechanical impedance, 2) control strategies to search for, and adjust to, a suitable mechanical impedance for assistance and 3) sensing technologies for classifying the tasks in which the human engages.The first part of this dissertation characterizes a pneumatic variable stiffness actuator named an Active/Passive Pneumatic Actuator (AP2A). The actuator consists of an air cylinder and an array of solenoid valves. These valves and the corresponding switching algorithms tune the chamber pressures and make the AP2A function as a mechanical spring with desired stiffness. The actuator has a low mechanical impedance compared to geared motors, which enables it to achieve efficient interaction. Control strategies of an assistive system with the AP2A are discussed in the second part. This control framework utilizes the characteristics of the AP2A to provide assistance when necessary and to operate transparently (i.e., neither to assist nor to disturb the users) otherwise. Energy consumed by the AP2A and the assisted system is minimized by solving an optimal control problem. Finally, an estimator is introduced to detect assistive timing for the assistive system with the AP2A. This estimator utilizes physiological signals such as surface electromyogram and prior knowledge of a muscular model, classifying if the user is under the specified condition to be assisted by the AP2A. It demonstrates that the user's effort can be saved, also reducing the number of procedures to collect training data for the estimator before using assistive systems. The performance of the actuator, the controller, and the estimator proposed in this dissertation are verified through experiments.From the above, this dissertation contributes to developing the AP2A that provides assistance and saves energy usage of assistive systems by working as a mechanical spring with stiffness optimized for achieving effective interaction under specific conditions. This actuator supports assistive devices that can be deployed in the real world, properly assisting the users when needed

Wearable exoskeleton systems based-on pneumatic soft actuators and controlled by parallel processing

Human assistance innovation is essential in an increasingly aging society and one technology that may be applicable is exoskeletons. However, traditional rigid exoskeletons have many drawbacks. This research includes the design and implementation of upper-limb power assist and rehabilitation exoskeletons based on pneumatic soft actuators. A novel extensor-contractor pneumatic muscle has been designed and constructed. This new actuator has bidirectional action, allowing it to both extend and contract, as well as create force in both directions. A mathematical model has been developed for the new novel actuator which depicts the output force of the actuator. Another new design has been used to create a novel bending pneumatic muscle, based on an extending McKibben muscle and modelled mathematically according to its geometric parameters. This novel bending muscle design has been used to create two versions of power augmentation gloves. These exoskeletons are controlled by adaptive controllers using human intention. For finger rehabilitation a glove has been developed to bend the fingers (full bending) by using our novel bending muscles. Inspired by the zero position (straight fingers) problem for post-stroke patients, a new controllable stiffness bending actuator has been developed with a novel prototype. To control this new rehabilitation exoskeleton, online and offline controller systems have been designed for the hand exoskeleton and the results have been assessed experimentally. Another new design of variable stiffness actuator, which controls the bending segment, has been developed to create a new version of hand exoskeletons in order to achieve more rehabilitation movements in the same single glove. For Forearm rehabilitation, a rehabilitation exoskeleton has been developed for pronation and supination movements by using the novel extensor-contractor pneumatic muscle. For the Elbow rehabilitation an elbow rehabilitation exoskeleton was designed which relies on novel two-directional bending actuators with online and offline feedback controllers. Lastly for upper-limb joint is the wrist, we designed a novel all-directional bending actuator by using the moulding bladder to develop the wrist rehabilitation exoskeleton by a single all-directional bending muscle. Finally, a totally portable, power assistive and rehabilitative prototype has been developed using a parallel processing intelligent control chip