Robust fractional-order fast terminal sliding mode control with fixed-time reaching law for high-performance nanopositioning

Open Access via the Wiley Agreement ACKNOWLEDGEMENTS This work is supported by the China Scholarship Council under Grant No. 201908410107 and by the National Natural Science Foundation of China under Grant No. 51505133. The authors also thank the anonymous reviewers for their insightful and constructive comments.Peer reviewedPublisher PD

On-line estimation approaches to fault-tolerant control of uncertain systems

This thesis is concerned with fault estimation in Fault-Tolerant Control (FTC) and as such involves the joint problem of on-line estimation within an adaptive control system. The faults that are considered are significant uncertainties affecting the control variables of the process and their estimates are used in an adaptive control compensation mechanism. The approach taken involves the active FTC, as the faults can be considered as uncertainties affecting the control system. The engineering (application domain) challenges that are addressed are: (1) On-line model-based fault estimation and compensation as an FTC problem, for systems with large but bounded fault magnitudes and for which the faults can be considered as a special form of dynamic uncertainty. (2) Fault-tolerance in the distributed control of uncertain inter-connected systems The thesis also describes how challenge (1) can be used in the distributed control problem of challenge (2). The basic principle adopted throughout the work is that the controller has two components, one involving the nominal control action and the second acting as an adaptive compensation for significant uncertainties and fault effects. The fault effects are a form of uncertainty which is considered too large for the application of passive FTC methods. The thesis considers several approaches to robust control and estimation: augmented state observer (ASO); sliding mode control (SMC); sliding mode fault estimation via Sliding Mode Observer (SMO); linear parameter-varying (LPV) control; two-level distributed control with learning coordination

Semi-blind robust indentification and robust control approach to personalized anemia management.

The homeostatic blood hemoglobin (Hb) content of a healthy individual varies between the range of 14-18 g/dL for a male and 12-16 g/dL for a female. This quantity provides an estimate of red blood cell (RBC) count in circulation at any given moment. RBC is a protein carrying substance that transports oxygen from the lungs to other tissues in the body and is synthesized by the kidney through a process known as erythropoiesis where erythropoietin is secreted in response to hypoxia. In this regard, the kidneys act not only as a controller but also as a sensor in regulating RBC levels. Patients with chronic kidney diseases (CKD) have dysfunctional kidneys that compromise these fundamental kidney functions. Consequently, anemia is developed. Anemics of CKD have low levels of Hb that must be controlled and properly regulated to the appropriate therapeutic range. Until the discovery of recombinant human erythropoietin (EPO) over three decades ago, treatment procedure of anemia conditions primarily involved repeated blood transfusions–a process known to be associated with several other health related complications. This discovery resulted in a paradigm shift in anemia management from blood transfusions to dosage therapies. The main objective of anemia management with EPO is to increase patients’ hemoglobin level from low to a suitable therapeutic range as defined by the National Kidney Foundation-Kidney Disease Outcomes Quality Initiative (NKF-KDOI) to be in the range of 10 - 12 g/dL while avoiding response values beyond 14 g/dL to prevent other complications associated with EPO medication. It is therefore imperative that clinicians balance dosage efficacy and toxicity in anemia management therapies. At most treatment facilities, protocols are developed to conform to NKF-KDOI recommendations. These protocols are generally based on EPO packet inserts and the expected Hb responses from the average patient. The inevitable variability within the patient group makes this “one-size-fits-all” dosing scheme non-optimal, at best, and potentially dangerous for certain group of patients that do not adhere to the notion of expected “average” response. A dosing strategy that is tailored to the individual patients’ response to EPO medication could provide a better alternative to the current treatment methods. An objective of this work is to develop EPO dosing strategies tailored to the individual patients using robust identification techniques and modern feedback control methods. First, a unique model is developed based on Hb responses and dosage EPO of the individual patients using semi-blind robust identification techniques. This provides a nominal model and a quantitative information on model uncertainty that accounts for other possible patient’s dynamics not considered in the modeling process. This is in the framework of generalized interpolation theory. Then, from the derived nominal model and the associated uncertainty information, robust controller is designed via the =H1-synthesis methods to provide a new dosing strategies for the individual patients. The H1 control theory has a feature of minimizing the influence of some unknown worst case gain disturbance on a system. Finally, a framework is provided to strategize dosing protocols for newly admitted patients

Approximate Gaussian Conjugacy: Parametric Recursive Filtering Under Nonlinearity, Multimodal, Uncertainty, and Constraint, and Beyond

This is a post-peer-review, pre-copyedit version of an article published in Frontiers of Information Technology & Electronic Engineering. The final authenticated version is available online at: https://doi.org/10.1631/FITEE.1700379Since the landmark work of R. E. Kalman in the 1960s, considerable efforts have been devoted to time series state space models for a large variety of dynamic estimation problems. In particular, parametric filters that seek analytical estimates based on a closed-form Markov–Bayes recursion, e.g., recursion from a Gaussian or Gaussian mixture (GM) prior to a Gaussian/GM posterior (termed ‘Gaussian conjugacy’ in this paper), form the backbone for a general time series filter design. Due to challenges arising from nonlinearity, multimodality (including target maneuver), intractable uncertainties (such as unknown inputs and/or non-Gaussian noises) and constraints (including circular quantities), etc., new theories, algorithms, and technologies have been developed continuously to maintain such a conjugacy, or to approximate it as close as possible. They had contributed in large part to the prospective developments of time series parametric filters in the last six decades. In this paper, we review the state of the art in distinctive categories and highlight some insights that may otherwise be easily overlooked. In particular, specific attention is paid to nonlinear systems with an informative observation, multimodal systems including Gaussian mixture posterior and maneuvers, and intractable unknown inputs and constraints, to fill some gaps in existing reviews and surveys. In addition, we provide some new thoughts on alternatives to the first-order Markov transition model and on filter evaluation with regard to computing complexity

Highly redundant and fault tolerant actuator system: control, condition monitoring and experimental validation

This thesis is concerned with developing a control and condition monitoring system for a class of fault tolerant actuators with high levels of redundancy. The High Redundancy Actuator (HRA) is a concept inspired by biomimetics that aims to provide fault tolerance using relatively large numbers of actuation elements which are assembled in parallel and series configurations to form a single actuator. Each actuation element provides a small contribution to the overall force and displacement of the system. Since the capability of each actuation element is small, the effect of faults within the individual element of the overall system is also small. Hence, the HRA will gracefully degrade instead of going from fully functional to total failure in the presence of faults. Previous research on HRA using electromechanical technology has focused on a relatively low number of actuation elements (i.e. 4 elements), which were controlled with multiple loop control methods. The objective of this thesis is to expand upon this, by considering an HRA with a larger number of actuation elements (i.e. 12 elements). First, a mathematical model of a general n-by-m HRA is derived from first principles. This method can be used to represent any size of electromechanical HRA with actuation elements arranged in a matrix form. Then, a mathematical model of a 4-by-3 HRA is obtained from the general n-by-m model and verified experimentally using the HRA test rig. This actuator model is then used as a foundation for the controller design and condition monitoring development. For control design, two classical and control method-based controllers are compared with an H_infinity approach. The objective for the control design is to make the HRA track a position demand signal in both health and faulty conditions. For the classical PI controller design, the first approach uses twelve local controllers (1 per actuator) and the second uses only a single global controller. For the H_infinity control design, a mixed sensitivity functions is used to obtain good tracking performance and robustness to modelling uncertainties. Both of these methods demonstrate good tracking performance, with a slower response in the presence of faults. As expected, the H_infinity control method's robustness to modelling uncertainties, results in a smaller performance degradation in the presence of faults, compared with the classical designs. Unlike previous work, the thesis also makes a novel contribution to the condition monitoring of HRA. The proposed algorithm does not require the use of multiple sensors. The condition monitoring scheme is based on least-squares parameter estimation and fuzzy logic inference. The least-squares parameter estimation estimates the physical parameters of the electromechanical actuator based on input-output data collected from real-time experiments, while the fuzzy logic inference determines the health condition of the actuator based on the estimated physical parameters. Hence, overall, a new approach to both control and monitoring of an HRA is proposed and demonstrated on a twelve elements HRA test rig

Design of Energy Management Strategies for a Battery-Ultracapacitor Electric Vehicle

The battery pack is the most expensive component in electric vehicles. Electric vehicles are prone to accelerated battery degradation due to the high charging/discharging cycles and high peak power demand. One solution to this issue would be increasing the battery capacity to meet the high energy requests. However, increasing the battery size is not reasonable due to the high cost and volume. An alternative solution is integrating other energy storage systems into the vehicle powertrain. The additional energy storage system highlights an energy management strategy to distribute the power among onboard energy storage systems effectively. Energy management systems incorporate different strategies classified based on their computational time, implementability in real-time, and measurable performance to be optimized. This thesis considers the case study of Chevy Spark model year 2015 with a hybrid energy storage system including battery and ultracapacitor. First, an overview of diffrent energy storage systems is presented, followed by a review of different hybrid energy storage' configurations. Second, energy management strategies are categorized into three main classifications: rule-based, optimization-based, and data-based algorithms. Third, the selected vehicle model with an embedded rule-based energy management strategy is developed in MATLAB Simulink, and battery performance is validated against available real-world data. Optimal power distribution among battery and ultracapacitor is achieved through an offline global optimal algorithm in chapter 5 in a way to improve battery life. Finally, optimal results are used as a training dataset for an online data-based energy management strategy. Results prove the strategy's effectiveness by improving battery life by an average of 16% compared to the rule-based and 12% difference from the globally optimal strategy on various driving conditions. The proposed energy management strategy provides near-optimal performance while it is real-time implementable and does not need to have beforehand knowledge of driving cycles

Design and verification of Guidance, Navigation and Control systems for space applications

In the last decades, systems have strongly increased their complexity in terms of number of functions that can be performed and quantity of relationships between functions and hardware as well as interactions of elements and disciplines concurring to the definition of the system. The growing complexity remarks the importance of defining methods and tools that improve the design, verification and validation of the system process: effectiveness and costs reduction without loss of confidence in the final product are the objectives that have to be pursued. Within the System Engineering context, the modern Model and Simulation based approach seems to be a promising strategy to meet the goals, because it reduces the wasted resources with respect to the traditional methods, saving money and tedious works. Model Based System Engineering (MBSE) starts from the idea that it is possible at any moment to verify, through simulation sessions and according to the phase of the life cycle, the feasibility, the capabilities and the performances of the system. Simulation is used during the engineering process and can be classified from fully numerical (i.e. all the equipment and conditions are reproduced as virtual model) to fully integrated hardware simulation (where the system is represented by real hardware and software modules in their operational environment). Within this range of simulations, a few important stages can be defined: algorithm in the loop (AIL), software in the loop (SIL), controller in the loop (CIL), hardware in the loop (HIL), and hybrid configurations among those. The research activity, in which this thesis is inserted, aims at defining and validating an iterative methodology (based on Model and Simulation approach) in support of engineering teams and devoted to improve the effectiveness of the design and verification of a space system with particular interest in Guidance Navigation and Control (GNC) subsystem. The choice of focusing on GNC derives from the common interest and background of the groups involved in this research program (ASSET at Politecnico di Torino and AvioSpace, an EADS company). Moreover, GNC system is sufficiently complex (demanding both specialist knowledge and system engineer skills) and vital for whatever spacecraft and, last but not least the verification of its behavior is difficult on ground because strong limitations on dynamics and environment reproduction arise. Considering that the verification should be performed along the entire product life cycle, a tool and a facility, a simulator, independent from the complexity level of the test and the stage of the project, is needed. This thesis deals with the design of the simulator, called StarSim, which is the real heart of the proposed methodology. It has been entirely designed and developed from the requirements definition to the software implementation and hardware construction, up to the assembly, integration and verification of the first simulator release. In addition, the development of this technology met the modern standards on software development and project management. StarSim is a unique and self-contained platform: this feature allows to mitigate the risk of incompatibility, misunderstandings and loss of information that may arise using different software, simulation tools and facilities along the various phases. Modularity, flexibility, speed, connectivity, real time operation, fidelity with real world, ease of data management, effectiveness and congruence of the outputs with respect to the inputs are the sought-after features in the StarSim design. For every iteration of the methodology, StarSim guarantees the possibility to verify the behavior of the system under test thanks to the permanent availability of virtual models, that substitute all those elements not yet available and all the non-reproducible dynamics and environmental conditions. StarSim provides a furnished and user friendly database of models and interfaces that cover different levels of detail and fidelity, and supports the updating of the database allowing the user to create custom models (following few, simple rules). Progressively, pieces of the on board software and hardware can be introduced without stopping the process of design and verification, avoiding delays and loss of resources. StarSim has been used for the first time with the CubeSats belonging to the e-st@r program. It is an educational project carried out by students and researchers of the “CubeSat Team Polito” in which StarSim has been mainly used for the payload development, an Active Attitude Determination and Control System, but StarSim’s capabilities have also been updated to evaluate functionalities, operations and performances of the entire satellite. AIL, SIL, CIL, HIL simulations have been performed along all the phases of the project, successfully verifying a great number of functional and operational requirements. In particular, attitude determination algorithms, control laws, modes of operation have been selected and verified; software has been developed step by step and the bugs-free executable files have been loaded on the micro-controller. All the interfaces and protocols as well as data and commands handling have been verified. Actuators, logic and electrical circuits have been designed, built and tested and sensors calibration has been performed. Problems such as real time and synchronization have been solved and a complete hardware in the loop simulation test campaign both for A-ADCS standalone and for the entire satellite has been performed, verifying the satisfaction of a great number of CubeSat functional and operational requirements. The case study represents the first validation of the methodology with the first release of StarSim. It has been proven that the methodology is effective in demonstrating that improving the design and verification activities is a key point to increase the confidence level in the success of a space mission

Summary of Research 1994

The views expressed in this report are those of the authors and do not reflect the official policy or position of the Department of Defense or the U.S. Government.This report contains 359 summaries of research projects which were carried out under funding of the Naval Postgraduate School Research Program. A list of recent publications is also included which consists of conference presentations and publications, books, contributions to books, published journal papers, and technical reports. The research was conducted in the areas of Aeronautics and Astronautics, Computer Science, Electrical and Computer Engineering, Mathematics, Mechanical Engineering, Meteorology, National Security Affairs, Oceanography, Operations Research, Physics, and Systems Management. This also includes research by the Command, Control and Communications (C3) Academic Group, Electronic Warfare Academic Group, Space Systems Academic Group, and the Undersea Warfare Academic Group