Design for pre-bond testability in 3D integrated circuits

In this dissertation we propose several DFT techniques specific to 3D stacked IC systems. The goal has explicitly been to create techniques that integrate easily with existing IC test systems. Specifically, this means utilizing scan- and wrapper-based techniques, two foundations of the digital IC test industry. First, we describe a general test architecture for 3D ICs. In this architecture, each tier of a 3D design is wrapped in test control logic that both manages tier test pre-bond and integrates the tier into the large test architecture post-bond. We describe a new kind of boundary scan to provide the necessary test control and observation of the partial circuits, and we propose a new design methodology for test hardcore that ensures both pre-bond functionality and post-bond optimality. We present the application of these techniques to the 3D-MAPS test vehicle, which has proven their effectiveness. Second, we extend these DFT techniques to circuit-partitioned designs. We find that boundary scan design is generally sufficient, but that some 3D designs require special DFT treatment. Most importantly, we demonstrate that the functional partitioning inherent in 3D design can potentially decrease the total test cost of verifying a circuit. Third, we present a new CAD algorithm for designing 3D test wrappers. This algorithm co-designs the pre-bond and post-bond wrappers to simultaneously minimize test time and routing cost. On average, our algorithm utilizes over 90% of the wires in both the pre-bond and post-bond wrappers. Finally, we look at the 3D vias themselves to develop a low-cost, high-volume pre-bond test methodology appropriate for production-level test. We describe the shorting probes methodology, wherein large test probes are used to contact multiple small 3D vias. This technique is an all-digital test method that integrates seamlessly into existing test flows. Our experimental results demonstrate two key facts: neither the large capacitance of the probe tips nor the process variation in the 3D vias and the probe tips significantly hinders the testability of the circuits. Taken together, this body of work defines a complete test methodology for testing 3D ICs pre-bond, eliminating one of the key hurdles to the commercialization of 3D technology.PhDCommittee Chair: Lee, Hsien-Hsin; Committee Member: Bakir, Muhannad; Committee Member: Lim, Sung Kyu; Committee Member: Vuduc, Richard; Committee Member: Yalamanchili, Sudhaka

Software-based and regionally-oriented traffic management in Networks-on-Chip

Since the introduction of chip-multiprocessor systems, the number of integrated cores has been steady growing and workload applications have been adapted to exploit the increasing parallelism. This changed the importance of efficient on-chip communication significantly and the infrastructure has to keep step with these new requirements. The work at hand makes significant contributions to the state-of-the-art of the latest generation of such solutions, called Networks-on-Chip, to improve the performance, reliability, and flexible management of these on-chip infrastructures

Analyses and design strategies for fundamental enabling building blocks: Dynamic comparators, voltage references and on-die temperature sensors

Dynamic comparators and voltage references are among the most widely used fundamental building blocks for various types of circuits and systems, such as data converters, PLLs, switching regulators, memories, and CPUs. As thermal constraints quickly emerged as a dominant performance limiter, on-die temperature sensors will be critical to the reliable operation of future integrated circuits. This dissertation investigates characteristics of these three enabling circuits and design strategies for improving their performances. One of the most critical specifications of a dynamic comparator is its input referred offset voltage, which is pivotal to achieving overall system performance requirements of many mixed-signal circuits and systems. Unlike offset voltages in other circuits such as amplifiers, the offset voltage in a dynamic comparator is extremely challenging to analyze and predict analytically due to its dependence on transient response and due to internal positive feedback and time-varying operating points in the comparator. In this work, a novel balanced method is proposed to facilitate the evaluation of time-varying operating points of transistors in a dynamic comparator. Two types of offsets are studied in the model: (1) static offset voltage caused by mismatches in mobilities, transistor sizes, and threshold voltages, and (2) dynamic offset voltage caused by mismatches in parasitic capacitors or loading capacitors. To validate the proposed method, dynamic comparators in two prevalent topologies are implemented in 0.25 μm and 40 nm CMOS technologies. Agreement between predicted results and simulated results verifies the effectiveness of the proposed method. The new method and the analytical models enable designers to identify the most dominant contributors to offset and to optimize the dynamic comparators\u27 performances. As an illustrating example, the Lewis-Gray dynamic comparator was analyzed using the balanced method and redesigned to minimize its offset voltage. Simulation results show that the offset voltage was easily reduced by 41% while maintaining the same silicon area. A bandgap voltage reference is one of the core functional blocks in both analog and digital systems. Despite the reported improvements in performance of voltage references, little attention has been focused on theoretical characterizations of non-ideal effects on the value of the output voltage, on the inflection point location and on the curvature of the reference voltage. In this work, a systematic approach is proposed to analytically determine the effects of two non-ideal elements: the temperature dependent gain-determining resistors and the amplifier offset voltage. The effectiveness of the analytical models is validated by comparing analytical results against Spectre simulation results. Research on on-die temperature sensor design has received rapidly increasing attention since component and power density induced thermal stress has become a critical factor in the reliable operation of integrated circuits. For effective power and thermal management of future multi-core systems, hundreds of sensors with sufficient accuracy, small area and low power are required on a single chip. This work introduces a new family of highly linear on chip temperature sensors. The proposed family of temperature sensors expresses CMOS threshold voltage as an output. The sensor output is independent of power supply voltage and independent of mobility values. It can achieve very high temperature linearity, with maximum nonlinearity around +/- 0.05oC over a temperature range of -20oC to 100oC. A sizing strategy based on combined analytical analysis and numerical optimization has been presented. Following this method, three circuits A, B and C have been designed in standard 0.18 ym CMOS technology, all achieving excellent linearity as demonstrated by Cadence Spectre simulations. Circuits B and C are the modified versions of circuit A, and have improved performance at the worst corner-low voltage supply and high threshold voltage corner. Finally, a direct temperature-to-digital converter architecture is proposed as a master-slave hybrid temperature-to-digital converter. It does not require any traditional constant reference voltage or reference current, it does not attempt to make any node voltage or branch current constant or precisely linear to temperature, yet it generates a digital output code that is very linear with temperature

Dynamic Digital Optical Tomography for Cancer Imaging and Therapy Monitoring

Diffuse optical tomography is a non-invasive imaging technique that uses near-infrared light to create three-dimensional images of tissue. This dissertation presents the design and validation of an instrument for rapid optical imaging using digital detection techniques. In addition to a detailed description of the instrument, three studies are presented: a clinical study detecting breast cancer using dynamic optical imaging; a pre-clinical study monitoring early tumor response to anti-angiogenic therapy; and a clinical study monitoring individual patient response to neoadjuvant chemotherapy. These studies show that diffuse optical tomography is a valuable imaging modality that can play an important role in cancer detection and treatment

Proceedings of the Mobile Satellite Conference

A satellite-based mobile communications system provides voice and data communications to mobile users over a vast geographic area. The technical and service characteristics of mobile satellite systems (MSSs) are presented and form an in-depth view of the current MSS status at the system and subsystem levels. Major emphasis is placed on developments, current and future, in the following critical MSS technology areas: vehicle antennas, networking, modulation and coding, speech compression, channel characterization, space segment technology and MSS experiments. Also, the mobile satellite communications needs of government agencies are addressed, as is the MSS potential to fulfill them