Discussion of the technology and research in fuel injectors common rail system

Common rail is one of the most important components in a diesel and gasoline direct injection system. It features a high-pressure (100 bar) fuel rail feeding solenoid valves, as opposed to a low-pressure fuel pump feeding unit injectors. Third-generation common rail diesels now feature piezoelectric injectors for increased precision, with fuel pressures up to 2,500 bar. The purpose of this review paper is to investigate the technology and research in fuel injectors common rail system. This review paper focuses on component of common rail injection system, pioneer of common rail injection, characteristics of common rail injection system, method to reduce smoke and NOx emission simultaneously and impact of common rail injection system. Based on our research, it can be concluded that common rail injection gives many benefit such as good for the engine performance, safe to use, and for to reduce the emission of the vehicle. Fuel injection common rail system is the modern technology that must be developed. Nowadays, our earth is polluting by vehicle output such as smoke. If the common rail system is developed, it can reduce the pollution and keep our atmosphere clean and safe

A unified analysis of PWM converters in discontinuous modes

Three discontinuous operating modes of PWM (pulsewidth modulated) converters are considered: the discontinuous inductor current mode (DICM), the discontinuous capacitor voltage mode (DCVM), and a previously unidentified mode called the discontinuous quasi-resonant mode (DQRM). DC and small-signal AC analyses are applicable to all basic PWM converter topologies. Any particular topology is taken into account via its DC conversion ratio in the continuous conduction mode. The small-signal model is of the same order as the state-space averaged model for the continuous mode, and it offers improved predictions of the low-frequency dynamics of PWM converters in the discontinuous modes. It is shown that converters in discontinuous modes exhibit lossless damping similar to the effect of the current-mode programming

An Integral Battery Charger with Power Factor Correction for Electric Scooter

This paper presents an integral battery charger for an electric scooter with high voltage batteries and interior-permanent-magnet motor traction drive. The battery charger is derived from the power hardware of the scooter, with the ac motor drive that operates as three-phase boost rectifier with power factor correction capability. The control of the charger is also integrated into the scooter control firmware that is implemented on a fixed-point DSP controller. Current-controlled or voltage-controlled charge modes are actuated according to the requirements of the battery management system, that is embedded into the battery pack. With respect to previous integrated chargers, the ac current is absorbed at unitary power factor with no harmonic distortion. Moreover, no additional filtering is needed since the pulsewidth modulation ripple is minimized by means of phase interleaving. The feasibility of the integral charger with different ac motors (induction motor, surface-mounted phase modulation motor) is also discussed, by means of a general model purposely developed for three-phase ac machines. The effectiveness of the proposed battery charger is experimentally demonstrated on a prototype electric scooter, equipped with two Li-ion battery packs rated 260 V, 20 A

A comparative study of electric power distribution systems for spacecraft

The electric power distribution systems for spacecraft are compared concentrating on two interrelated issues: the choice between dc and high frequency ac, and the converter/inverter topology to be used at the power source. The relative merits of dc and ac distribution are discussed. Specific converter and inverter topologies are identified and analyzed in detail for the purpose of detailed comparison. Finally, specific topologies are recommended for use in dc and ac systems

Single-Stage Power Electronic Converters with Combined Voltage Step-Up/Step-Down Capability

Power electronic converters are typically either step-down converters that take an input voltage and produce an output voltage of low amplitude or step-up converters that take an input voltage and produce an output voltage of higher amplitude. There are, however, applications where a converter that can step-up voltage or step-down voltage can be very useful, such as in applications where a converter needs to operate under a wide range of input and output voltage conditions such as a grid-connected solar inverter. Such converters, however, are not as common as converters that can only step down or step up voltage because most applications require converters that need to only step down voltage or only step up voltage and such converters have better performance within a limited voltage range than do converters that are designed for very wide voltage ranges. Nonetheless, there are applications where converters with step-down and step-up capability can be used advantageously. The main objectives of this thesis are to propose new power electronic converters that can step up voltage and step down voltage and to investigate their characteristics. This will be done for two specific converter types: AC/DC single-stage converters and DC-AC inverters. In this thesis, two new AC/DC single-stage converters and a new three-phase converter are proposed and their operation and steady-state characteristics are examined in detail. The feasibility of each new converter is confirmed with results obtained from an experimental prototype and the feasibility of a control method for the inverter is confirmed with simulation work using commercially available software such as MATLAB and PSIM

Dynamic modeling of pwm and single-switch single-stage power factor correction converters

The concept of averaging has been used extensively in the modeling of power electronic circuits to overcome their inherent time-variant nature. Among various methods, the PWM switch modeling approach is most widely accepted in the study of closed-loop stability and transient response because of its accuracy and simplicity. However, a non-ideal PWM switch model considering conduction losses is not available except for converters operating in continuous conduction mode (CCM) and under small ripple conditions. Modeling of conductor losses under large ripple conditions has not been reported in the open literature, especially when the converter operates in discontinuous conduction mode (DCM). In this dissertation, new models are developed to include conduction losses in the non-ideal PWM switch model under CCM and DCM conditions. The developed model is verified through two converter examples and the effect of conduction losses on the steady state and dynamic responses of the converter is also studied. Another major constraint of the PWM switch modeling approach is that it heavily relies on finding the three-terminal PWM switch. This requirement severely limits its application in modeling single-switch single-stage power factor correction (PFC) converters, where more complex topological structures and switching actions are often encountered. In this work, we developed a new modeling approach which extends the PWM switch concept by identifying the charging and discharging voltages applied to the inductors. The new method can be easily applied to derive large-signal models for a large group of PFC converters and the procedure is elaborated through a specific example. Finally, analytical results regarding harmonic contents and power factors of various PWM converters in PFC applications are also presented here

A unified analysis of converters with resonant switches

Quasi-resonant converters are a recently introduced family of single-switch resonant converters featuring zero-current or zero-voltage switching. Recognition of the topological structure uniting these converters — and the PWM converters on which they are based — leads to general models of their dc and low-frequency ac behavior. An expression is derived that yields the dc conversion ratio of a quasi-resonant converter in terms of the well-known conversion ratio of the underlying PWM topology. A small-signal, low-frequency dynamic model is developed whose parameters also incorporate the PWM conversion ratio. The dc and ac models reveal that any quasi-resonant converter with a full-wave resonant switch has dc and low-frequency behavior identical to that of its PWM parent, with switching frequency control replacing duty ratio control. Converters with half-wave resonant switches act more like PWM converters under current programming or discontinuous conduction mode, exhibiting lossless damping in the small-signal model and output resistance at dc