Indoor wireless communications and applications

Chapter 3 addresses challenges in radio link and system design in indoor scenarios. Given the fact that most human activities take place in indoor environments, the need for supporting ubiquitous indoor data connectivity and location/tracking service becomes even more important than in the previous decades. Specific technical challenges addressed in this section are(i), modelling complex indoor radio channels for effective antenna deployment, (ii), potential of millimeter-wave (mm-wave) radios for supporting higher data rates, and (iii), feasible indoor localisation and tracking techniques, which are summarised in three dedicated sections of this chapter

28 GHz and 73 GHz Millimeter-Wave Indoor Propagation Measurements and Path Loss Models

This paper presents 28 GHz and 73 GHz millimeter- wave propagation measurements performed in a typical office environment using a 400 Megachip-per-second broadband sliding correlator channel sounder and highly directional steerable 15 dBi (30 degrees beamwidth) and 20 dBi (15 degrees beamwidth) horn antennas. Power delay profiles were acquired for 48 transmitter-receiver location combinations over distances ranging from 3.9 m to 45.9 m with maximum transmit powers of 24 dBm and 12.3 dBm at 28 GHz and 73 GHz, respectively. Directional and omnidirectional path loss models and RMS delay spread statistics are presented for line-of-sight and non-line-of-sight environments for both co- and cross-polarized antenna configurations. The LOS omnidirectional path loss exponents were 1.1 and 1.3 at 28 GHz and 73 GHz, and 2.7 and 3.2 in NLOS at 28 GHz and 73 GHz, respectively, for vertically-polarized antennas. The mean directional RMS delay spreads were 18.4 ns and 13.3 ns, with maximum values of 193 ns and 288 ns at 28 GHz and 73 GHz, respectively.Comment: 7 pages, 9 figures, 2015 IEEE International Conference on Communications (ICC), ICC Workshop

5G 3GPP-like Channel Models for Outdoor Urban Microcellular and Macrocellular Environments

For the development of new 5G systems to operate in bands up to 100 GHz, there is a need for accurate radio propagation models at these bands that currently are not addressed by existing channel models developed for bands below 6 GHz. This document presents a preliminary overview of 5G channel models for bands up to 100 GHz. These have been derived based on extensive measurement and ray tracing results across a multitude of frequencies from 6 GHz to 100 GHz, and this document describes an initial 3D channel model which includes: 1) typical deployment scenarios for urban microcells (UMi) and urban macrocells (UMa), and 2) a baseline model for incorporating path loss, shadow fading, line of sight probability, penetration and blockage models for the typical scenarios. Various processing methodologies such as clustering and antenna decoupling algorithms are also presented.Comment: To be published in 2016 IEEE 83rd Vehicular Technology Conference Spring (VTC 2016-Spring), Nanjing, China, May 201

On the Frequency Dependency of Radio Channel's Delay Spread: Analyses and Findings From mmMAGIC Multi-frequency Channel Sounding

This paper analyzes the frequency dependency of the radio propagation channel's root mean square (rms) delay spread (DS), based on the multi-frequency measurement campaigns in the mmMAGIC project. The campaigns cover indoor, outdoor, and outdoor-to-indoor (O2I) scenarios and a wide frequency range from 2 to 86 GHz. Several requirements have been identified that define the parameters which need to be aligned in order to make a reasonable comparison among the different channel sounders employed for this study. A new modelling approach enabling the evaluation of the statistical significance of the model parameters from different measurements and the establishment of a unified model is proposed. After careful analysis, the conclusion is that any frequency trend of the DS is small considering its confidence intervals. There is statistically significant difference from the 3GPP New Radio (NR) model TR 38.901, except for the O2I scenario.Comment: This paper has been accepted to the 2018 12th European Conference on Antennas and Propagation (EuCAP), London, UK, April 201

Diversity textile antenna systems for firefighters

Off-body communication systems are valuable to improve the security of rescue workers by allowing them to transmit vital information collected by sensors. As rescue workers often work in indoor environments characterized by many obstructions, non line-of-sight propagation with multipath effects and shadowing compromises the performance of the wireless communication. The reliability is enhanced drastically by the use of diversity techniques. In the measurement campaign presented, the performance of such an off-body diversity system is compared for two antenna configurations: two dual-polarized antennas, versus four circularly polarized antennas. The actual data transmission confirms the marginal difference between the two configurations, suggesting the use of dual-polarized systems for reasons of user convenience and ease of practical implementation

Methods and criteria for performance analysis of multiantenna systems in mobile communications

Multiple-input multiple-output (MIMO) technique is one of the most promising solutions for increasing reliability and spectral efficiency of the radio connection in future mobile communication systems. The performance potential of MIMO systems is well established from theoretical point of view. However, much effort is still needed in the experimental verification of those systems using realistic antennas and channels. It is widely accepted that the antenna properties are of significant importance regarding the performance of single-input single-output (SISO) systems. However, the effect of the antennas on MIMO systems has not been thoroughly studied. Due to the complexity of MIMO systems, evaluation of MIMO antennas becomes increasingly cumbersome and time-consuming process in comparison to simpler systems. In the first part of this work an advanced antenna evaluation technique called experimental plane-wave based method (EPWBM) is generalized and validated to cover MIMO systems. This work is the extension of the previous work where the method has been used in the analysis of SISO systems. The EPWBM is based on the measured or simulated complex 3-D radiation patterns of the antennas and measured directional radio channel data. The EPWBM simplifies antenna evaluation process in comparison to traditional means since the same channel library can be utilized in the evaluation of several antenna systems without performing the same measurements for each prototype antennas separately. It is verified that the EPWBM is sufficiently reliable in comparing the performance of prototype antennas. In the second part of the work new quality factors for MIMO system evaluation enclosing traditional systems as special cases have been developed. The MIMO channel correlation matrix is formulated so that it reveals the ability of MIMO antenna systems to transfer signal power from a transmitter to a receiver and to utilize parallel spatial channels. It is also verified that correct normalization of the channel matrices is of significant importance in the MIMO antenna evaluation. This approach gives comprehensive framework for MIMO antenna evaluation, which takes into account both realistic antenna and channel properties. In the last part of the work insight into the performance of different antennas in different signal propagation environments is given. The performance of the antennas depends on the signal-to-noise-ratio and on the outage probability level considered. Although MIMO systems are based on the utilization of parallel spatial channels, the capability of the system to transfer signal power plays a significant role especially with small MIMO systems. In the realistic dynamic channels the capacity variation is larger than in the ideal channels, which are based on the identically and independently distributed (iid) channel assumption. Large performance variations occur in the realistic channels with directive antennas, when antennas are rotated in the usage environment, whereas omnidirectional ones are more robust but are difficult to realize in practice. The largest differences between the antennas are found at the low outage probability levels due to different radiation properties of the antennas. The systems with the cross-polarized antennas have smaller eigenvalue dispersion and are more robust in performance for the variations of the channel than the systems with co-polarized antennas. On the other hand, the co-polarized antennas possess better capability to transfer signal power and are more robust in performance for the antenna array orientation. From practical point of view, the dual-polarized antennas seem to be the most feasible candidates to be used in MIMO antenna systems due to compact structure, and indoor seems to be the most suitable for MIMO applications due to typically scatter-rich channel.Multiple-input multiple-output (MIMO) tekniika on yksi lupaavimmista ratkaisuista lisätä radioyhteyden luotettavuutta ja spektritehokkuutta tulevaisuuden matkaviestinjärjestelmissä. MIMO järjestelmien suorituskykypotentiaali on teoreettisesti todistettu. Paljon työtä tarvitaan kuitenkin vielä kokeelliseen järjestelmätestaukseen käyttäen realistisia antenneja ja kanavia. On laajasti hyväksyttyä että antennien ominaisuudet ovat merkityksellisiä single-input single-output (SISO) järjestelmien suorituskyvyn kannalta. Antennien vaikutusta MIMO-järjestelmiin ei ole kuitenkaan perusteellisesti tutkittu. MIMO-järjestelmien lisääntyneestä monimutkaisuudesta johtuen, verrattuna yksinkertaisempiin järjestelmiin, MIMO antennien suorituskyvyn arviointi hankaloituu ja vie enemmän aikaa. Työn ensimmäisessä osassa uusi antennien arviointitekniikka nimeltään kokeellinen tasoaaltoihin perustuva menetelmä (EPWBM) on yleistetty käsittämään MIMO järjestelmät ja sen tarkkuus on arvioitu. Tämä työ on laajennus aikaisempaan työhön jossa menetelmää on käytetty SISO-järjestelmien arviointiin. EPWBM perustuu mitattuihin tai simuloituihin antennien kompleksisiin 3-D suuntakuvioihin ja mitattuun suuntatiedon sisältämään kanavadataan. EPWBM yksinkertaistaa antennin suorituskyvyn arviointia perinteisiin menetelmiin verrattuna, koska sama kanavamittausaineisto voidaan hyödyntää usamman antennisysteemin arvioinnissa tekemättä samoja mittauksia jokaiselle antenniprototyypille erikseen. On osoitettu että EPWBM on suhteellisen luotettava prototyyppiantennien suorituskyvyn vertailussa. Työn toisessa osassa on kehitetty uusia hyvyyslukuja MIMO-järjestelmien suorituskyvyn arviointiin sisältäen perinteiset järjestelmät erikoistapauksina. MIMO-kanavamatriisi esitetään siten että se paljastaa MIMO-antennijärjestelmien kyvyn siirtää signaalitehoa lähettimen ja vastaanottimen välillä ja hyödyntää rinnakkaisia kanavia. On myös todistettu että oikeanlainen kanavamatriisien normalisointi on erittäin merkittävää MIMO-antennivertailussa. Tämä lähestymistapa antaa kattavat puitteet MIMO-antennien suorituskyvyn arviointiin ottaen huomioon todelliset antennien ja kanavan ominaisuudet. Työn viimeisessä osassa annetaan käsitys erilaisten antennien suorituskyvystä erilaisissa signaalin etenemisympäristöissä. Antennien suorituskyky riippuu signaalikohinasuhteesta ja tarkasteltavan signaalin luotettavuustasosta. Vaikka MIMO-järjestelmät perustuvat rinnakkaisten kanavien hyödyntämiseen järjestelmän signaalitehon siirto-ominaisuudet ovat merkittäviä erityisesti pienillä MIMO järjestelmillä. Realistisissa dynaamisissa kanavissa kapasiteetinvaihtelu on suurempaa kuin ideaalisissa kanavissa jotka perustuvat oletukseen että signaalit ovat riippumattomasti ja identtisesti jakautuneita (iid). Suurta suorituskykyn vaihtelua esiintyy realistissa kanavissa suuntaavilla antenneilla, kun antenneja pyöritetään käyttöympäristössä, kun taas ympärisäteilevät antennit olisivat jäykempiä suorituskyvyn kannalta mutta käytännössä vaikeampia toteuttaa. Suuremmat erot antennien välillä on löydettävissä matalalta signaalin luotettavuustasolta johtuen antennien erilaisista säteilyominaisuuksista. Kaksipolarisaatioantennijärjestelmillä on pienempi ominaisarvohaje ja niiden suorituskyky on jäykempi kanavan vaihteluille kuin yksipolarisaatioantennijärjestelmä. Toisaalta yksipolarisaatioantenneilla on paremmat signaalitehon siirto-ominaisuudet ja suorituskyky vaihtelee vähemmän antennin katselusuunnan funktiona. Käytännön näkökulmasta katsoen kaksipolarisaatioantennit näyttävät olevan kaikkein toteuttamiskelpoisin vaihtoehto käytettäväksi MIMO-systeemeissä johtuen niiden kompaktista rakenteesta, ja sisätila näyttää olevan sopivin ympäristö MIMO-sovelluksiin johtuen tyypillisesti sirontarikkaasta kanavasta.reviewe

Evaluation of performance of mobile terminal antennas

Fast development of new mobile communications equipment results in demand for fast and reliable evaluation methods to estimate the performance of mobile terminals because the performance of antennas located on the terminals varies in different multipath propagation environments. Two methods presented in this thesis provide new possibilities in antenna design because, from now on, the performance of new antennas can be tested already before a prototype antenna is constructed by using existing radio channel libraries and simulated radiation patterns of the antennas. The performance can be estimated by calculating the mean effective gain (MEG) of the antenna using the elevation power distribution or by a plane wave -based method using sets of incident plane waves and the radiation pattern of an antenna. In addition to different propagation environments, the effects of the user on performance can be included in the evaluation. In this thesis, estimating the MEG of different antennas using the elevation power distribution and the power patterns of the antennas is shown to be an accurate and fast method by comparing the results with direct radio channel measurements. The mean difference between the methods is −0.18 dB with standard deviation of 0.19 dB. The usefulness of the evaluation method is demonstrated by evaluating the performance of several antennas located on mobile terminals. The antenna evaluation provided important and unique knowledge of the effect of both the environment and the user on performance. Because in calculating the radiation efficiency of the antenna we assume uniform incident field, the efficiency can result in a performance estimation that does not correspond to real usage situations. Therefore, including the environmental effects in the evaluation procedure is important, although the effect of the antenna is more important than the effect of the environment on MEG. It was noticed with calculated Gaussian-shaped beams that tilting or changing the beamwidth of a mobile terminal antenna has an effect of about 2 dB on MEG in multipath environments. Matching the polarization of the antenna to that of the environment can improve the performance more. A novel incident plane wave -based tool has been developed for evaluating the performance of antenna configurations designed for diversity and Multiple-Input Multiple-Output (MIMO) systems. In this thesis, the instantaneous joint contribution of incident field consisting of a number of extracted plane waves and the complex three-dimensional radiation pattern of the antenna is shown to be accurate and extremely fast way to estimate the diversity advantages of different antenna configurations in time-variable radio channels. The difference between the diversity gains achieved by the plane wave -based method and by the direct radio channel measurements is on average less than 0.9 dB. Moreover, the radio channel can be exactly the same for all antenna configurations under test. Furthermore, this thesis includes evaluation of the performance of different MIMO antenna configurations. The studied antenna configurations have been selected from the 16×64 MIMO channel measurement data. A novel way of using one omnidirectional reference antenna in a normalization procedure is shown to be reasonable especially in cases of antenna arrays consisting of directive elements. Three different propagation environments are used as evaluation platforms. The azimuth orientation of mobile terminal antennas may influence the performance of a MIMO antenna configuration significantly. In MIMO configurations compact dual-polarized receiving antennas provide capacity performance almost equal to the arrays employing single polarization.reviewe

RMS delay spread vs. coherence bandwidth from 5G indoor radio channel measurements at 3.5 GHz band

Our society has become fully submersed in fourth generation (4G) technologies, setting constant connectivity as the norm. Together with self-driving cars, augmented reality, and upcoming technologies, the new generation of Internet of Things (IoT) devices is pushing the development of fifth generation (5G) communication systems. In 5G architecture, increased capacity, improved data rate, and decreased latency are the objectives. In this paper, a measurement campaign is proposed; we focused on studying the propagation properties of microwaves at a center frequency of 3.5 GHz, commonly used in 5G cellular networks. Wideband measurement data were gathered at various indoor environments with different dimensions and characteristics. A ray-tracing analysis showed that the power spectrum is dominated by the line of sight component together with reflections on two sidewalls, indicating the practical applicability of our results. Two wideband parameters, root mean square delay spread and coherence bandwidth, were estimated for the considered scenarios, and we found that they are highly dependent on the physical dimension of the environment rather than on furniture present in the room. The relationship between both parameters was also investigated to provide support to network planners when obtaining the bandwidth from the delay spread, easily computed by a ray-tracing tool