A Compact 1:4 Lossless T-Junction Power Divider Using Open Complementary Split Ring Resonator

This paper presents the size miniaturized and harmonic suppressed lossless 1:4 T-junction unequal power divider using an open complementary split ring resonator (OCSRR). By embedding the OCSRR structure in the microstrip transmission line, slow wave effect is introduced and thereby size reduction is achieved. The dimensions of OCSRR are optimized to reduce the length of high impedance and low impedance quarter-wavelength transmission lines. In our design high impedance line length is reduced to 58.6%, and low impedance line length is reduced to 12% when compared to the conventional quarter wavelength lines. The proposed power divider is having small dimensions of 0.18 λg × 0.33 λg and is 51.94% smaller than the conventional unequal power divider

Compact and Wide Stopband Lowpass Filter Using Open Complementary Split Ring Resonator and Defected Ground Structure

A compact (0.16 λg x 0.08 λg) and wide stop¬band lowpass filter design using open complementary split ring resonator (OCSRR) and defected ground structure (DGS) is presented in this paper. Low pass filter is con-structed using two cascaded stages of OCSRR. Since the rejection bandwidth of the OCSRR is narrow, tapered dumbbell shaped DGS section is placed under the OCSRR to enhance the bandwidth. The cutoff frequency (fc) of the proposed lowpass filter is 1.09 GHz. The rejection band¬width of the filter covers the entire ultra wideband spec¬trum. Hence the spurious passband suppression is achieved up to 10 fc. The designed filter has been fabri¬cated and validated by experimental result

Design of High Performance Microstrip Dual-Band Bandpass Filter

This paper presents a new design of dual-band bandpass filters using coupled stepped-impedance resonators for wireless systems. This architecture uses multiple couple stubs to tune the passband frequencies and the filter characteristics are improved using defected ground structure (DGS) technique. Measurement results show insertion losses of 0.93 dB and 1.13 dB for the central frequencies of 2.35 GHz and 3.61 GHz, respectively. This filter is designed, fabricated and measured and the results of the simulation and measurement are in good agreement

Compact near field wireless energy transfer systems using defected ground structures

Near-Field Wireless Power Transfer systems have attracted attention for their potential applications, such as implanted medical devices, radio frequency identification, and portable electronic devices in general. In this context, a compact model for short-range NF-WPT systems operating in ISM frequency bands is proposed, employing the concept of ground plane aperture resonators or Defected Ground Structures (DGS). This technique allows the miniaturization of the resonator, which leads to the development of compact NF-WPT systems. The model proposed in this work aims at possible applications that require simultaneous energy and data transfer. This model operates in dual band in 433 MHz and 900 MHz frequency bands and makes use of overlapping circular DGS in order to shrink the resonator device and obtain high values of Figure of Merit (FoM) commonly used in this research area. The proposed model was designed using the electromagnetic analysis and built using Rogers RO4003 dielectric material. The designed dual-band DGS resonators have a total area of 11.7 × 10.2 mm 2 and when placed at a distance of 15 mm between transmitter and receiver, they have measured FoM values of 0.71 and 1.07 at 440 MHz and 918 MHz, respectively. The results were compared with related works found in the literature, and indicate a ηWPT of 40.9% and 49.2 %

Wideband and UWB antennas for wireless applications. A comprehensive review

A comprehensive review concerning the geometry, the manufacturing technologies, the materials, and the numerical techniques, adopted for the analysis and design of wideband and ultrawideband (UWB) antennas for wireless applications, is presented. Planar, printed, dielectric, and wearable antennas, achievable on laminate (rigid and flexible), and textile dielectric substrates are taken into account. The performances of small, low-profile, and dielectric resonator antennas are illustrated paying particular attention to the application areas concerning portable devices (mobile phones, tablets, glasses, laptops, wearable computers, etc.) and radio base stations. This information provides a guidance to the selection of the different antenna geometries in terms of bandwidth, gain, field polarization, time-domain response, dimensions, and materials useful for their realization and integration in modern communication systems

Numerical synthesis of filtering antennas

Dizertační práce je zaměřena na kompletní metodiku návrhu tří a čtyř prvkových flíčkových anténních řad, které neobsahují žádné filtrující části a přesto se chovají jako filtrující antény (filtény). Návrhová metodika kombinuje přístup pro návrh filtrů s přístupem pro anténní řady a zahrnuje tvarování frekvenčních odezev činitele odrazu a normovaného realizovaného zisku. Směr hlavního laloku přes pracovní pásmo je kontrolován také. S cílem kontrolovat tvary uvedených charakteristik, nové gi koeficienty jsou představeny pro návrh filtrujících anténních řad. Návrhová metodika byla ověřena na tří a čtyř prvkové filtrující anténní řadě přes frekvenční pásmo od 4,8 GHz do 6,8 GHz, pro šířku pásma celé struktury od 7 % do 14 % a pro požadovanou úroveň činitele odrazu od –10 dB do –20 dB. Celá metodika byla podpořena výrobou a měřením šesti testovacích vzorků filtrujících anténních řad s rozdílnými konfiguracemi. Ve všech případech se simulované a naměřené výsledky dobře shodují.The dissertation thesis is focused on a complete design methodology of a three and four-element patch antenna arrays which are without any filtering parts and yet behave like a filtering antenna (filtenna). This design combines filter and antenna approaches and includes shaping the frequency response of the reflection coefficient and the modelling of the frequency response of the normalized realized gain. The frequency response of the main lobe direction is controlled as well. In order to control the shape of these responses, a set of gi coefficients for designing the filtering antenna array are obtained. The design methodology was verified on the three-element and four-element filtennas over the frequency range from 4.8 GHz to 6.8 GHz; for fractional bandwidth from 7 % to 14 % and for level of the reflection coefficient from –10 dB to –20 dB. The whole design methodology was supported by manufacturing and measuring six test cases of the filtering antenna array with different configurations. Simulated and measured results show a good agreement in all cases.

Review on the Design of the Isolation Techniques for UWB-MIMO Antennas

Ultra wide band - Multiple Input Multiple Output antenna technology provides higher data rates and the combination of the ultra wide band (UWB) and the multiple input multiple output (MIMO) technologies provides a solution for the demand of still higher data rates i.e. in excess of 3 Gb/sec in the future.  As the antenna technologies are improving, the size of the MIMO antenna is growing smaller and smaller. Placing the antenna elements in such close proximity increases the coupling between them. Various isolation techniques have to be introduced between the antenna elements to decrease the coupling and to improve the isolation. A study of the various isolation enhancement techniques have been made in this review. It analyses the various isolation enhancement methods such as using orthogonal polarization, parasitic elements, varied decoupling structures, defected ground structures (DGS), neutralization line (NL) and finally by using metamaterials. Metamaterials is a technology to perk up the isolation between the antenna elements. Split ring resonator (SRR) behaves as a metamaterial and it is used as an isolation mechanism in this study. The antennas are simulated and the results are compared. The method using parasitic elements gives the highest isolation of 35 dB and it is 5 dB better than the methods using orthogonal polarization and using the decoupling structure. The performance of all the antennas satisfies the conditions for minimum isolation. The envelope correlation coefficient is nearly zero in all the antennas and it implies good diversity performance. The diversity gain is also calculated for the various antennas and it satisfies good diversity performance. The bandwidth of the antennas is in the UWB frequency range and they have a fractional bandwidth above the required value of 1.09. The capacity loss for all the antennas is very low and the antennas using defected ground structure and the decoupling structure gives very low capacity loss

A Review on Different Techniques of Mutual Coupling Reduction Between Elements of Any MIMO Antenna. Part 1: DGSs and Parasitic Structures

This two-part article presents a review of different techniques of mutual coupling (MC) reduction. MC is a major issue when an array of antennas is densely packed. When the separation between the antennas i

Low-profile dual-band pixelated defected ground antenna for multistandard IoT devices.

A low-profile dual-band pixelated defected ground antenna has been proposed at 3.5 GHz and 5.8 GHz bands. This work presents a flexible design guide for achieving single-band and dual-band antenna using pixelated defected ground (PDG). The unique pixelated defected ground has been designed using the binary particle swarm optimization (BPSO) algorithm. Computer Simulation Technology Microwave Studio incorporated with Matlab has been utilized in the antenna design process. The PDG configuration provides freedom of exploration to achieve the desired antenna performance. Compact antenna design can be achieved by making the best use of designated design space on the defected ground (DG) plane. Further, a V-shaped transfer function based on BPSO with fast convergence allows us to efficiently implement the PDG technique. In the design procedure, pixelization is applied to a small rectangular region of the ground plane. The square pixels on the designated defected ground area of the antenna have been formed using a binary bit string, consisting of 512 bits taken during each iteration of the algorithm. The PDG method is concerned with the shape of the DG and does not rely on the geometrical dimension analysis used in traditional defected ground antennas. Initially, three single band antennas have been designed at 3.5 GHz, 5.2 GHz and 5.8 GHz using PDG technique. Finally, same PDG area has been used to design a dual-band antenna at 3.5 GHz and 5.8 GHz. The proposed antenna exhibits almost omnidirectional radiation performance with nearly 90% efficiency. It also shows dual radiation pattern property with similar patterns having different polarizations at each operational band. The antenna is fabricated on a ROGERS RO4003 substrate with 1.52 mm thickness. Reflection coefficient and radiation patterns are measured to validate its performance. The simulated and measured results of the antenna are closely correlated. The proposed antenna is suitable for different applications in Internet of Things