Voltage and Time-Domain Analog Circuit Techniques for Scaled CMOS Technologies

CMOS technology scaling has resulted in reduced supply voltage and intrinsic voltage gain of the transistor. This presents challenges to the analog circuit designers due to lower signal swing and achievable signal to noise ratio (SNR), leading to increased power consumption. At the same time, device speed has increased in lower design nodes, which has not been directly beneficial for analog circuit design. This thesis presents voltage-domain and time-domain circuit scaling friendly circuit architectures that minimize the power consumption and benefit from the increasing transistor speeds. In the voltage-domain, an on-the-fly gain selection block is demonstrated as an alternative to the traditional MDAC architecture to enhance the input dynamic range of a medium-resolution medium-speed analog-to-digital converter (ADC) at reduced supply voltages. The proposed design also eliminates the need for a reference buffer, thus providing power savings. The measured prototype enhances the input dynamic range of a 12bit, 40MSPS ADC to 80.6dB at 1.2V supply voltage. In the time-domain, a generic circuit design approach is presented, followed by an in-depth analysis of Voltage-Controlled-Oscillator based Operational Transconductance Amplifiers (VCO-OTAs). A discrete-time-domain small-signal model based on the zero crossings of the internal VCOs is developed to predict the stability, the step response, and the frequency response of the circuit when placed in feedback. The model accurately predicts the circuit behavior for an arbitrary input frequency, even as the VCO free-running frequency approaches the unity-gain bandwidth of the closed-loop system, where other intuitive small-signal models available in the literature fail. Next, we present an application of VCO-OTA in designing a baseband trans-impedance amplifier (TIA) for current-mode receivers as a scaling-friendly and power-efficient alternative to the inverter-based OTA. We illustrate a design methodology for the choice of the VCO-OTA parameters in the context of a receiver design with an example of a 20MHz RF-channel-bandwidth receiver operating at 2GHz. Receiver simulation results demonstrate an improvement of up to 12dB in blocker 1dB compression point (B1dB) for slightly higher power consumption or up to 2.6x power reduction of the TIA resulting in up to 2x power reduction of the receiver for similar B1dB performance. Next, we present some examples of VCO-OTAs. We first illustrate the benefit of a VCO-OTA in a low-dropout-voltage regulator to achieve a dropout voltage of only100mV and operating down to 0.8V input supply, compared to the prototype based on traditional OTA with a minimum dropout voltage of 150mV, operating at a minimum of 1.2V supply. Both the capacitor-less prototypes can drive up to 1nF load capacitor and provide a current of 60mA. The next prototype showcases a method to reduce the power consumption of a VCO-OTA and spurs at the VCO frequency, with an application in the design of a fourth-order Butterworth filter at 4MHz. The thesis concludes with a design example of 0.2V VCO-OTA

Analog Baseband Filters and Mixed Signal Circuits for Broadband Receiver Systems

Data transfer rates of communication systems continue to rise fueled by aggressive demand for voice, video and Internet data. Device scaling enabled by modern lithography has paved way for System-on-Chip solutions integrating compute intensive digital signal processing. This trend coupled with demand for low power, battery-operated consumer devices offers extensive research opportunities in analog and mixed-signal designs that enable modern communication systems. The first part of the research deals with broadband wireless receivers. With an objective to gain insight, we quantify the impact of undesired out-band blockers on analog baseband in a broadband radio. We present a systematic evaluation of the dynamic range requirements at the baseband and A/D conversion boundary. A prototype UHF receiver designed using RFCMOS 0.18[mu]m technology to support this research integrates a hybrid continuous- and discrete-time analog baseband along with the RF front-end. The chip consumes 120mW from a 1.8V/2.5V dual supply and achieves a noise figure of 7.9dB, an IIP3 of -8dBm (+2dbm) at maximum gain (at 9dB RF attenuation). High linearity active RC filters are indispensable in wireless radios. A novel feed-forward OTA applicable to active RC filters in analog baseband is presented. Simulation results from the chip prototype designed in RFCMOS 0.18[mu]m technology show an improvement in the out-band linearity performance that translates to increased dynamic range in the presence of strong adjacent blockers. The second part of the research presents an adaptive clock-recovery system suitable for high-speed wireline transceivers. The main objective is to improve the jitter-tracking and jitter-filtering trade-off in serial link clock-recovery applications. A digital state-machine that enables the proposed mixed-signal adaptation solution to achieve this objective is presented. The advantages of the proposed mixed-signal solution operating at 10Gb/s are supported by experimental results from the prototype in RFCMOS 0.18[mu]m technology

A built-in self-test technique for high speed analog-to-digital converters

Fundação para a Ciência e a Tecnologia (FCT) - PhD grant (SFRH/BD/62568/2009

Design of frequency synthesizers for short range wireless transceivers

The rapid growth of the market for short-range wireless devices, with standards such as Bluetooth and Wireless LAN (IEEE 802.11) being the most important, has created a need for highly integrated transceivers that target drastic power and area reduction while providing a high level of integration. The radio section of the devices designed to establish communications using these standards is the limiting factor for the power reduction efforts. A key building block in a transceiver is the frequency synthesizer, since it operates at the highest frequency of the system and consumes a very large portion of the total power in the radio. This dissertation presents the basic theory and a design methodology of frequency synthesizers targeted for short-range wireless applications. Three different examples of synthesizers are presented. First a frequency synthesizer integrated in a Bluetooth receiver fabricated in 0.35μm CMOS technology. The receiver uses a low-IF architecture to downconvert the incoming Bluetooth signal to 2MHz. The second synthesizer is integrated within a dual-mode receiver capable of processing signals of the Bluetooth and Wireless LAN (IEEE 802.11b) standards. It is implemented in BiCMOS technology and operates the voltage controlled oscillator at twice the required frequency to generate quadrature signals through a divide-by-two circuit. A phase switching prescaler is featured in the synthesizer. A large capacitance is integrated on-chip using a capacitance multiplier circuit that provides a drastic area reduction while adding a negligible phase noise contribution. The third synthesizer is an extension of the second example. The operation range of the VCO is extended to cover a frequency band from 4.8GHz to 5.85GHz. By doing this, the synthesizer is capable of generating LO signals for Bluetooth and IEEE 802.11a, b and g standards. The quadrature output of the 5 - 6 GHz signal is generated through a first order RC - CR network with an automatic calibration loop. The loop uses a high frequency phase detector to measure the deviation from the 90° separation between the I and Q branches and implements an algorithm to minimize the phase errors between the I and Q branches and their differential counterparts

Power-efficient Circuit Architectures for Receivers Leveraging Nanoscale CMOS

Cellular and mobile communication markets, together with CMOS technology scaling, have made complex systems-on-chip integrated circuits (ICs) ubiquitous. Moving towards the internet of things that aims to extend this further requires ultra-low power and efficient radio communication that continues to take advantage of nanoscale CMOS processes. At the heart of this lie orthogonal challenges in both system and circuit architectures of current day technology. By enabling transceivers at center frequencies ranging in several tens of GHz, modern CMOS processes support bandwidths of up to several GHz. However, conventional narrowband architectures cannot directly translate or trade-off these speeds to lower power consumption. Pulse-radio UWB (PR-UWB), a fundamentally different system of communication enables this trade-off by bit-level duty-cycling i.e., power-gating and has emerged as an alternative to conventional narrowband systems to achieve better energy efficiency. However, system-level challenges in the implementation of transceiver synchronization and duty-cycling have remained an open challenge to realize the ultra-low power numbers that PR-UWB promises. Orthogonally, as CMOS scaling continues, approaching 28nm and 14nm in production digital processes, the key transistor characteristics have rapidly changed. Changes in supply voltage, intrinsic gain and switching speeds have rendered conventional analog circuit design techniques obsolete, since they do not scale well with the digital backend engines that dictate scaling. Consequently, circuit architectures that employ time-domain processing and leverage the faster switching speeds have become attractive. However, they are fundamentally limited by their inability to support linear domain-to-domain conversion and hence, have remained un-suited to high-performance applications. Addressing these requirements in different dimensions, two pulse-radio UWB receiver and a continuous-time filter silicon prototypes are presented in this work. The receiver prototypes focus on system level innovation while the filter serves as a demonstration vehicle for novel circuit architectures developed in this work. The PR-UWB receiver prototypes are implemented in a 65nm LP CMOS technology and are fully integrated solutions. The first receiver prototype is a compact UWB receiver front end operating at 4.85GHz that is aggressively duty-cycled. It occupies an active area of only 0.4 mm², thanks to the use of few inductors and RF G_m-C filters and incorporates an automatic-threshold-recovery-based demodulator for digitization. The prototype achieves a sensitivity of -88dBm at a data rate of 1Mbps (for a BER of 10^-3), while achieving the lowest energy consumption gradient (dP/df_data=450pJ/bit) amongst other receivers operating in the lower UWB band, for the same sensitivity. However, this prototype is limited by idle-time power consumption (e.g., bias) and lacks synchronization capability. A fully self-duty-cycled and synchronized UWB pulse-radio receiver SoC targeted at low-data-rate communication is presented as the second prototype. The proposed architecture builds on the automatic-threshold-recovery-based demodulator to achieve synchronization using an all-digital clock and data recovery loop. The SoC synchronizes with the incoming pulse stream from the transmitter and duty-cycles itself. The SoC prototype achieves a -79.5dBm, 1Mbps-normalized sensitivity for a >5X improvement over the state of the art in power consumption (375pJ/bit), thanks to aggressive signal path and bias circuit duty-cycling. The SoC is fully integrated to achieve RF-in to bit-out operation and can interface with off-chip, low speed digital components. Finally, switched-mode signal processing, a signal processing paradigm that enables the design of highly linear, power-efficient feedback amplifiers is presented. A 0.6V continuous-time filter prototype that demonstrates the advantages of this technique is presented in a 65nm GP CMOS process. The filter draws 26.2mW from the supply while operating at a full-scale that is 73% of the V_dd, a bandwidth of 70MHz and a peak signal-to-noise-and-distortion ratio (SNDR) of 55.8dB. This represents a 2-fold improvement in full-scale and a 10-fold improvement in the bandwidth over state-of-the-art filter implementations, while demonstrating excellent linearity and signal-to-noise ratio. To sum up, innovations spanning both system and circuit architectures that leverage the speeds of nanoscale CMOS processes to enable power-efficient solutions to next-generation wireless receivers are presented in this work

CMOS ASIC Design of Multi-frequency Multi-constellation GNSS Front-ends

With the emergence of the new global navigation satellite systems (GNSSs) such as Galileo, COMPASS and GLONASS, the US Global Positioning System (GPS) has new competitors. This multiplicity of constellations will offer new services and a much better satellite coverage. Public regulated service (PRS) is one of these new services that Galileo, the first global positioning service under civilian control, will offers. The PRS is a proprietary encrypted navigation designed to be more reliable and robust against jamming and provides premium quality in terms of position and timing and continuity of service, but it requires the use of FEs with extended capabilities. The project that this thesis starts from, aims to develop a dual frequency (E1 and E6) PRS receiver with a focus on a solution for professional applications that combines affordability and robustness. To limit the production cost, the choice of a monolithic design in a multi-purpose 0.18 µm complementary metal-oxide-semiconductor (CMOS) technology have been selected, and to reduce the susceptibility to interference, the targeted receiver is composed of two independent FEs. The first ASIC described here is such FEs bundle. Each FE is composed of a radio frequency (RF) chain that includes a low-noise amplifier (LNA), a quadrature mixer, a frequency synthesizer (FS), two intermediate frequency (IF) filters, two variable-gain amplifiers (VGAs) and two 6-bit flash analog-to-digital converters (ADCs). Each have an IF bandwidth of 50 MHz to accommodate the wide-band PRS signals. The FE achieves a 30 dB of dynamic gain control at each channel. The complete receivers occupies a die area of 11.5 mm2 while consuming 115 mW from a supply of a 1.8 V. The second ASIC that targets civilian applications, is a reconfigurable single-channel FE that permits to exploit the interoperability among GNSSs. The FE can operate in two modes: a ¿narrow-band mode¿, dedicated to Beidou-B1 with an IF bandwidth of 8 MHz, and a ¿wide-band mode¿ with an IF bandwidth of 23 MHz, which can accommodate simultaneous reception of Beidou-B1/GPS-L1/Galileo-E1. These two modes consumes respectively 22.85 mA and 28.45 mA from a 1.8 V supply. Developed with the best linearity in mind, the FE shows very good linearity with an input-referred 1 dB compression point (IP1dB) of better than -27.6 dBm. The FE gain is stepwise flexible from 39 dB and to a maximum of 58 dB. The complete FE occupies a die area of only 2.6 mm2 in a 0.18 µm CMOS. To also accommodate the wide-band PRS signals in the IF section of the FE, a highly selective wide-tuning-range 4th-order Gm-C elliptic low-pass filter is used. It features an innovative continuous tuning circuit that adjusts the bias current of the Gm cell¿s input stage to control the cutoff frequency. With this circuit, the power consumption is proportional to the cutoff frequency thus the power efficiency is achieved while keeping the linearity near constant. Thanks to a Gm switching technique, which permit to keep the signal path switchless, the filter shows an extended tuning of the cutoff frequency that covers continuously a range from 7.4 MHz to 27.4 MHz. Moreover the abrupt roll-off of up to 66 dB/octave, can mitigate out-of-band interference. The filter consumes 2.1 mA and 7.5 mA at its lowest and highest cutoff frequencies respectively, and its active area occupies, 0.23 mm2. It achieves a high input-referred third-order intercept point (IIP3) of up to -1.3 dBVRMS

High performance continuous-time filters for information transfer systems

Vast attention has been paid to active continuous-time filters over the years. Thus as the cheap, readily available integrated circuit OpAmps replaced their discrete circuit versions, it became feasible to consider active-RC filter circuits using large numbers of OpAmps. Similarly the development of integrated operational transconductance amplifier (OTA) led to new filter configurations. This gave rise to OTA-C filters, using only active devices and capacitors, making it more suitable for integration. The demands on filter circuits have become ever more stringent as the world of electronics and communications has advanced. In addition, the continuing increase in the operating frequencies of modern circuits and systems increases the need for active filters that can perform at these higher frequencies; an area where the LC active filter emerges. What mainly limits the performance of an analog circuit are the non-idealities of the used building blocks and the circuit architecture. This research concentrates on the design issues of high frequency continuous-time integrated filters. Several novel circuit building blocks are introduced. A novel pseudo-differential fully balanced fully symmetric CMOS OTA architecture with inherent common-mode detection is proposed. Through judicious arrangement, the common-mode feedback circuit can be economically implemented. On the level of system architectures, a novel filter low-voltage 4th order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled-inductors, thus providing bandwidth tuning with small passband ripple. As part of a direct conversion dual-mode 802.11b/Bluetooth receiver, a BiCMOS 5th order low-pass channel selection filter is designed. The filter operated from a single 2.5V supply and achieves a 76dB of out-of-band SFDR. A digital automatic tuning system is also implemented to account for process and temperature variations. As part of a Bluetooth transmitter, a low-power quadrature direct digital frequency synthesizer (DDFS) is presented. Piecewise linear approximation is used to avoid using a ROM look-up table to store the sine values in a conventional DDFS. Significant saving in power consumption, due to the elimination of the ROM, renders the design more suitable for portable wireless communication applications

Low jitter phase-locked loop clock synthesis with wide locking range

The fast growing demand of wireless and high speed data communications has driven efforts to increase the levels of integration in many communications applications. Phase noise and timing jitter are important design considerations for these communications applications. The desire for highly complex levels of integration using low cost CMOS technologies works against the minimization of timing jitter and phase noise for communications systems which employ a phase-locked loop for frequency and clock synthesis with on-chip VCO. This dictates an integrated CMOS implementation of the VCO with very low phase noise performance. The ring oscillator VCOs based on differential delay cell chains have been used successfully in communications applications, but thermal noise induced phase noise have to be minimized in order not to limit their applicability to some applications which impose stringent timing jitter and phase noise requirements on the PLL clock synthesizer. Obtaining lower timing jitter and phase noise at the PLL output also requires the minimization of noise in critical circuit design blocks as well as the optimization of the loop bandwidth of the PLL. In this dissertation the fundamental performance limits of CMOS PLL clock synthesizers based on ring oscillator VCOs are investigated. The effect of flicker and thermal noise in MOS transistors on timing jitter and phase noise are explored, with particular emphasis on source coupled NMOS differential delay cells with symmetric load elements. Several new circuit architectures are employed for the charge pump circuit and phase-frequency detector (PFD) to minimize the timing jitter due to the finite dead zone in the PFD and the current mismatch in the charge pump circuit. The selection of the optimum PLL loop bandwidth is critical in determining the phase noise performance at the PLL output. The optimum loop bandwidth and the phase noise performance of the PLL is determined using behavioral simulations. These results are compared with transistor level simulated results and experimental results for the PLL clock synthesizer fabricated in a 0.35 µm CMOS technology with good agreement. To demonstrate the proposed concept, a fully integrated CMOS PLL clock synthesizer utilizing integer-N frequency multiplier technique to synthesize several clock signals in the range of 20-400 MHz with low phase noise was designed. Implemented in a standard 0.35-µm N-well CMOS process technology, the PLL achieves a period jitter of 6.5-ps (rms) and 38-ps (peak-to-peak) at 216 MHz with a phase noise of -120 dBc/Hz at frequency offsets above 10 KHz. The specific research contributions of this work include (1) proposing, designing, and implementing a new charge pump circuit architecture that matches current levels and therefore minimizes one source of phase noise due to fluctuations in the control voltage of the VCO, (2) an improved phase-frequency detector architecture which has improved characteristics in lock condition, (3) an improved ring oscillator VCO with excellent thermal noise induced phase noise characteristics, (4) the application of selfbiased techniques together with fixed bias to CMOS low phase noise PLL clock synthesizer for digital video communications ,and (5) an analytical model that describes the phase noise performance of the proposed VCO and PLL clock synthesizer

System-level design and RF front-end implementation for a 3-10ghz multiband-ofdm ultrawideband receiver and built-in testing techniques for analog and rf integrated circuits

This work consists of two main parts: a) Design of a 3-10GHz UltraWideBand (UWB) Receiver and b) Built-In Testing Techniques (BIT) for Analog and RF circuits. The MultiBand OFDM (MB-OFDM) proposal for UWB communications has received significant attention for the implementation of very high data rate (up to 480Mb/s) wireless devices. A wideband LNA with a tunable notch filter, a downconversion quadrature mixer, and the overall radio system-level design are proposed for an 11-band 3.4-10.3GHz direct conversion receiver for MB-OFDM UWB implemented in a 0.25mm BiCMOS process. The packaged IC includes an RF front-end with interference rejection at 5.25GHz, a frequency synthesizer generating 11 carrier tones in quadrature with fast hopping, and a linear phase baseband section with 42dB of gain programmability. The receiver IC mounted on a FR-4 substrate provides a maximum gain of 67-78dB and NF of 5-10dB across all bands while consuming 114mA from a 2.5V supply. Two BIT techniques for analog and RF circuits are developed. The goal is to reduce the test cost by reducing the use of analog instrumentation. An integrated frequency response characterization system with a digital interface is proposed to test the magnitude and phase responses at different nodes of an analog circuit. A complete prototype in CMOS 0.35mm technology employs only 0.3mm2 of area. Its operation is demonstrated by performing frequency response measurements in a range of 1 to 130MHz on 2 analog filters integrated on the same chip. A very compact CMOS RF RMS Detector and a methodology for its use in the built-in measurement of the gain and 1dB compression point of RF circuits are proposed to address the problem of on-chip testing at RF frequencies. The proposed device generates a DC voltage proportional to the RMS voltage amplitude of an RF signal. A design in CMOS 0.35mm technology presents and input capacitance <15fF and occupies and area of 0.03mm2. The application of these two techniques in combination with a loop-back test architecture significantly enhances the testability of a wireless transceiver system

On-Chip Analog Circuit Design Using Built-In Self-Test and an Integrated Multi-Dimensional Optimization Platform

Nowadays, the rapid development of system-on-chip (SoC) market introduces tremendous complexity into the integrated circuit (IC) design. Meanwhile, the IC fabrication process is scaling down to allow higher density of integration but makes the chips more sensitive to the process-voltage-temperature (PVT) variations. A successful IC product not only imposes great pressure on the IC designers, who have to handle wider variations and enforce more design margins, but also challenges the test procedure, leading to more check points and longer test time. To relax the designers’ burden and reduce the cost of testing, it is valuable to make the IC chips able to test and tune itself to some extent. In this dissertation, a fully integrated in-situ design validation and optimization (VO) hardware for analog circuits is proposed. It implements in-situ built-in self-test (BIST) techniques for analog circuits. Based on the data collected from BIST, the error between the measured and the desired performance of the target circuit is evaluated using a cost function. A digital multi-dimensional optimization engine is implemented to adaptively adjust the analog circuit parameters, seeking the minimum value of the cost function and achieving the desired performance. To verify this concept, study cases of a 2nd/4th active-RC band-pass filter (BPF) and a 2nd order Gm-C BPF, as well as all BIST and optimization blocks, are adopted on-chip. Apart from the VO system, several improved BIST techniques are also proposed in this dissertation. A single-tone sinusoidal waveform generator based on a finite-impulse-response (FIR) architecture, which utilizes an optimization algorithm to enhance its spur free dynamic range (SFDR), is proposed. It achieves an SFDR of 59 to 70 dBc from 150 to 850 MHz after the optimization procedure. A low-distortion current-steering two-tone sinusoidal signal synthesizer based on a mixing-FIR architecture is also proposed. The two-tone synthesizer extends the FIR architecture to two stages and implements an up-conversion mixer to generate the two tones, achieving better than -68 dBc IM3 below 480 MHz LO frequency without calibration. Moreover, an on-chip RF receiver linearity BIST methodology for continuous and discrete-time hybrid baseband chain is proposed. The proposed receiver chain implements a charge-domain FIR filter to notch the two excitation signals but expose the third order intermodulation (IM3) tones. It simplifies the linearity measurement procedure–using a power detector is enough to analyze the receiver’s linearity. Finally, a low cost fully digital built-in analog tester for linear-time-invariant (LTI) analog blocks is proposed. It adopts a time-to-digital converter (TDC) to measure the delays corresponded to a ramp excitation signal and is able to estimate the pole or zero locations of a low-pass LTI system