Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases

[EN] The first generation of Terrestrial Digital Television(DTV) has been in service for over a decade. In 2013, several countries have already completed the transition from Analog to Digital TV Broadcasting, most of which in Europe. In South America, after several studies and trials, Brazil adopted the Japanese standard with some innovations. Japan and Brazil started Digital Terrestrial Television Broadcasting (DTTB) services in December 2003 and December 2007 respectively, using Integrated Services Digital Broadcasting - Terrestrial (ISDB-T), also known as ARIB STD-B31. In June 2005 the Committee for the Information Technology Area (CATI) of Brazilian Ministry of Science and Technology and Innovation MCTI approved the incorporation of the IC-Brazil Program, in the National Program for Microelectronics (PNM) . The main goals of IC-Brazil are the formal qualification of IC designers, support to the creation of semiconductors companies focused on projects of ICs within Brazil, and the attraction of semiconductors companies focused on the design and development of ICs in Brazil. The work presented in this thesis originated from the unique momentum created by the combination of the birth of Digital Television in Brazil and the creation of the IC-Brazil Program by the Brazilian government. Without this combination it would not have been possible to make these kind of projects in Brazil. These projects have been a long and costly journey, albeit scientifically and technologically worthy, towards a Brazilian DTV state-of-the-art low complexity Integrated Circuit, with good economy scale perspectives, due to the fact that at the beginning of this project ISDB-T standard was not adopted by several countries like DVB-T. During the development of the ISDB-T receiver proposed in this thesis, it was realized that due to the continental dimensions of Brazil, the DTTB would not be enough to cover the entire country with open DTV signal, specially for the case of remote localizations far from the high urban density regions. Then, Eldorado Research Institute and Idea! Electronic Systems, foresaw that, in a near future, there would be an open distribution system for high definition DTV over satellite, in Brazil. Based on that, it was decided by Eldorado Research Institute, that would be necessary to create a new ASIC for broadcast satellite reception. At that time DVB-S2 standard was the strongest candidate for that, and this assumption still stands nowadays. Therefore, it was decided to apply to a new round of resources funding from the MCTI - that was granted - in order to start the new project. This thesis discusses in details the Architecture and Algorithms proposed for the implementation of a low complexity Intermediate Frequency(IF) ISDB-T Receiver on Application Specific Integrated Circuit (ASIC) CMOS. The Architecture proposed here is highly based on the COordinate Rotation Digital Computer (CORDIC) Algorithm, that is a simple and efficient algorithm suitable for VLSI implementations. The receiver copes with the impairments inherent to wireless channels transmission and the receiver crystals. The thesis also discusses the Methodology adopted and presents the implementation results. The receiver performance is presented and compared to those obtained by means of simulations. Furthermore, the thesis also presents the Architecture and Algorithms for a DVB-S2 receiver targeting its ASIC implementation. However, unlike the ISDB-T receiver, only preliminary ASIC implementation results are introduced. This was mainly done in order to have an early estimation of die area to prove that the project in ASIC is economically viable, as well as to verify possible bugs in early stage. As in the case of ISDB-T receiver, this receiver is highly based on CORDIC algorithm and it was prototyped in FPGA. The Methodology used for the second receiver is derived from that used for the ISDB-T receiver, with minor additions given the project characteristics.[ES] La primera generación de Televisión Digital Terrestre(DTV) ha estado en servicio por más de una década. En 2013, varios países completaron la transición de transmisión analógica a televisión digital, la mayoría de ellas en Europa. En América del Sur, después de varios estudios y ensayos, Brasil adoptó el estándar japonés con algunas innovaciones. Japón y Brasil comenzaron a prestar el servicio de Difusión de Televisión Digital Terrestre (DTTB) en diciembre de 2003 y diciembre de 2007 respectivamente, utilizando Radiodifusión Digital de Servicios Integrados Terrestres (ISDB-T), también conocida como ARIB STD-B31. En junio de 2005, el Comité del Área de Tecnología de la Información (CATI) del Ministerio de Ciencia, Tecnología e Innovación de Brasil - MCTI aprobó la incorporación del Programa CI-Brasil, en el Programa Nacional de Microelectrónica (PNM). Los principales objetivos de la CI-Brasil son la formación de diseñadores de CIs, apoyar la creación de empresas de semiconductores enfocadas en proyectos de circuitos integrados dentro de Brasil, y la atracción de empresas de semiconductores interesadas en el diseño y desarrollo de circuitos integrados. El trabajo presentado en esta tesis se originó en el impulso único creado por la combinación del nacimiento de la televisión digital en Brasil y la creación del Programa de CI-Brasil por el gobierno brasileño. Sin esta combinación no hubiera sido posible realizar este tipo de proyectos en Brasil. Estos proyectos han sido un trayecto largo y costoso, aunque meritorio desde el punto de vista científico y tecnológico, hacia un Circuito Integrado brasileño de punta y de baja complejidad para DTV, con buenas perspectivas de economía de escala debido al hecho que al inicio de este proyecto, el estándar ISDB-T no fue adoptado por varios países como DVB-T. Durante el desarrollo del receptor ISDB-T propuesto en esta tesis, se observó que debido a las dimensiones continentales de Brasil, la DTTB no sería suficiente para cubrir todo el país con la señal de televisión digital abierta, especialmente para el caso de localizaciones remotas, apartadas de las regiones de alta densidad urbana. En ese momento, el Instituto de Investigación Eldorado e Idea! Sistemas Electrónicos, previeron que en un futuro cercano habría un sistema de distribución abierto para DTV de alta definición por satélite en Brasil. Con base en eso, el Instituto de Investigación Eldorado decidió que sería necesario crear un nuevo ASIC para la recepción de radiodifusión por satélite, basada el estándar DVB-S2. En esta tesis se analiza en detalle la Arquitectura y algoritmos propuestos para la implementación de un receptor ISDB-T de baja complejidad y frecuencia intermedia (IF) en un Circuito Integrado de Aplicación Específica (ASIC) CMOS. La arquitectura aquí propuesta se basa fuertemente en el algoritmo Computadora Digital para Rotación de Coordenadas (CORDIC), el cual es un algoritmo simple, eficiente y adecuado para implementaciones VLSI. El receptor hace frente a las deficiencias inherentes a las transmisiones por canales inalámbricos y los cristales del receptor. La tesis también analiza la metodología adoptada y presenta los resultados de la implementación. Por otro lado, la tesis también presenta la arquitectura y los algoritmos para un receptor DVB-S2 dirigido a la implementación en ASIC. Sin embargo, a diferencia del receptor ISDB-T, se introducen sólo los resultados preliminares de implementación en ASIC. Esto se hizo principalmente con el fin de tener una estimación temprana del área del die para demostrar que el proyecto en ASIC es económicamente viable, así como para verificar posibles errores en etapa temprana. Como en el caso de receptor ISDB-T, este receptor se basa fuertemente en el algoritmo CORDIC y fue un prototipado en FPGA. La metodología utilizada para el segundo receptor se deriva de la utilizada para el re[CA] La primera generació de Televisió Digital Terrestre (TDT) ha estat en servici durant més d'una dècada. En 2013, diversos països ja van completar la transició de la radiodifusió de televisió analògica a la digital, i la majoria van ser a Europa. A Amèrica del Sud, després de diversos estudis i assajos, Brasil va adoptar l'estàndard japonés amb algunes innovacions. Japó i Brasil van començar els servicis de Radiodifusió de Televisió Terrestre Digital (DTTB) al desembre de 2003 i al desembre de 2007, respectivament, utilitzant la Radiodifusió Digital amb Servicis Integrats de (ISDB-T), coneguda com a ARIB STD-B31. Al juny de 2005, el Comité de l'Àrea de Tecnologia de la Informació (CATI) del Ministeri de Ciència i Tecnologia i Innovació del Brasil (MCTI) va aprovar la incorporació del programa CI Brasil al Programa Nacional de Microelectrònica (PNM). Els principals objectius de CI Brasil són la qualificació formal dels dissenyadors de circuits integrats, el suport a la creació d'empreses de semiconductors centrades en projectes de circuits integrats dins del Brasil i l'atracció d'empreses de semiconductors centrades en el disseny i desenvolupament de circuits integrats. El treball presentat en esta tesi es va originar en l'impuls únic creat per la combinació del naixement de la televisió digital al Brasil i la creació del programa Brasil CI pel govern brasiler. Sense esta combinació no hauria estat possible realitzar este tipus de projectes a Brasil. Estos projectes han suposat un viatge llarg i costós, tot i que digne científicament i tecnològica, cap a un circuit integrat punter de baixa complexitat per a la TDT brasilera, amb bones perspectives d'economia d'escala perquè a l'inici d'este projecte l'estàndard ISDB-T no va ser adoptat per diversos països, com el DVB-T. Durant el desenvolupament del receptor de ISDB-T proposat en esta tesi, va resultar que, a causa de les dimensions continentals de Brasil, la DTTB no seria suficient per cobrir tot el país amb el senyal de TDT oberta, especialment pel que fa a les localitzacions remotes allunyades de les regions d'alta densitat urbana.. En este moment, l'Institut de Recerca Eldorado i Idea! Sistemes Electrònics van preveure que, en un futur pròxim, no hi hauria a Brasil un sistema de distribució oberta de TDT d'alta definició a través de satèl¿lit. D'acord amb això, l'Institut de Recerca Eldorado va decidir que seria necessari crear un nou ASIC per a la recepció de radiodifusió per satèl¿lit. basat en l'estàndard DVB-S2. En esta tesi s'analitza en detall l'arquitectura i els algorismes proposats per l'execució d'un receptor ISDB-T de Freqüència Intermèdia (FI) de baixa complexitat sobre CMOS de Circuit Integrat d'Aplicacions Específiques (ASIC). L'arquitectura ací proposada es basa molt en l'algorisme de l'Ordinador Digital de Rotació de Coordenades (CORDIC), que és un algorisme simple i eficient adequat per implementacions VLSI. El receptor fa front a les deficiències inherents a la transmissió de canals sense fil i els cristalls del receptor. Esta tesi també analitza la metodologia adoptada i presenta els resultats de l'execució. Es presenta el rendiment del receptor i es compara amb els obtinguts per mitjà de simulacions. D'altra banda, esta tesi també presenta l'arquitectura i els algorismes d'un receptor de DVB-S2 de cara a la seua implementació en ASIC. No obstant això, a diferència del receptor ISDB-T, només s'introdueixen resultats preliminars d'implementació en ASIC. Això es va fer principalment amb la finalitat de tenir una estimació primerenca de la zona de dau per demostrar que el projecte en ASIC és econòmicament viable, així com per verificar possibles errors en l'etapa primerenca. Com en el cas del receptor ISDB-T, este receptor es basa molt en l'algorisme CORDIC i va ser un prototip de FPGA. La metodologia utilitzada per al segon receptor es deriva de la utilitzada per al receptor IRodrigues De Lima, E. (2016). Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/61967TESI

Analog Baseband Filters and Mixed Signal Circuits for Broadband Receiver Systems

Data transfer rates of communication systems continue to rise fueled by aggressive demand for voice, video and Internet data. Device scaling enabled by modern lithography has paved way for System-on-Chip solutions integrating compute intensive digital signal processing. This trend coupled with demand for low power, battery-operated consumer devices offers extensive research opportunities in analog and mixed-signal designs that enable modern communication systems. The first part of the research deals with broadband wireless receivers. With an objective to gain insight, we quantify the impact of undesired out-band blockers on analog baseband in a broadband radio. We present a systematic evaluation of the dynamic range requirements at the baseband and A/D conversion boundary. A prototype UHF receiver designed using RFCMOS 0.18[mu]m technology to support this research integrates a hybrid continuous- and discrete-time analog baseband along with the RF front-end. The chip consumes 120mW from a 1.8V/2.5V dual supply and achieves a noise figure of 7.9dB, an IIP3 of -8dBm (+2dbm) at maximum gain (at 9dB RF attenuation). High linearity active RC filters are indispensable in wireless radios. A novel feed-forward OTA applicable to active RC filters in analog baseband is presented. Simulation results from the chip prototype designed in RFCMOS 0.18[mu]m technology show an improvement in the out-band linearity performance that translates to increased dynamic range in the presence of strong adjacent blockers. The second part of the research presents an adaptive clock-recovery system suitable for high-speed wireline transceivers. The main objective is to improve the jitter-tracking and jitter-filtering trade-off in serial link clock-recovery applications. A digital state-machine that enables the proposed mixed-signal adaptation solution to achieve this objective is presented. The advantages of the proposed mixed-signal solution operating at 10Gb/s are supported by experimental results from the prototype in RFCMOS 0.18[mu]m technology

Timing and Carrier Synchronization in Wireless Communication Systems: A Survey and Classification of Research in the Last 5 Years

Timing and carrier synchronization is a fundamental requirement for any wireless communication system to work properly. Timing synchronization is the process by which a receiver node determines the correct instants of time at which to sample the incoming signal. Carrier synchronization is the process by which a receiver adapts the frequency and phase of its local carrier oscillator with those of the received signal. In this paper, we survey the literature over the last 5 years (2010–2014) and present a comprehensive literature review and classification of the recent research progress in achieving timing and carrier synchronization in single-input single-output (SISO), multiple-input multiple-output (MIMO), cooperative relaying, and multiuser/multicell interference networks. Considering both single-carrier and multi-carrier communication systems, we survey and categorize the timing and carrier synchronization techniques proposed for the different communication systems focusing on the system model assumptions for synchronization, the synchronization challenges, and the state-of-the-art synchronization solutions and their limitations. Finally, we envision some future research directions

Digitally-Assisted Mixed-Signal Wideband Compressive Sensing

Digitizing wideband signals requires very demanding analog-to-digital conversion (ADC) speed and resolution specifications. In this dissertation, a mixed-signal parallel compressive sensing system is proposed to realize the sensing of wideband sparse signals at sub-Nqyuist rate by exploiting the signal sparsity. The mixed-signal compressive sensing is realized with a parallel segmented compressive sensing (PSCS) front-end, which not only can filter out the harmonic spurs that leak from the local random generator, but also provides a tradeoff between the sampling rate and the system complexity such that a practical hardware implementation is possible. Moreover, the signal randomization in the system is able to spread the spurious energy due to ADC nonlinearity along the signal bandwidth rather than concentrate on a few frequencies as it is the case for a conventional ADC. This important new property relaxes the ADC SFDR requirement when sensing frequency-domain sparse signals. The mixed-signal compressive sensing system performance is greatly impacted by the accuracy of analog circuit components, especially with the scaling of CMOS technology. In this dissertation, the effect of the circuit imperfection in the mixed-signal compressive sensing system based on the PSCS front-end is investigated in detail, such as the finite settling time, the timing uncertainty and so on. An iterative background calibration algorithm based on LMS (Least Mean Square) is proposed, which is shown to be able to effectively calibrate the error due to the circuit nonideal factors. A low-speed prototype built with off-the-shelf components is presented. The prototype is able to sense sparse analog signals with up to 4 percent sparsity at 32 percent of the Nqyuist rate. Many practical constraints that arose during building the prototype such as circuit nonidealities are addressed in detail, which provides good insights for a future high-frequency integrated circuit implementation. Based on that, a high-frequency sub-Nyquist rate receiver exploiting the parallel compressive sensing is designed and fabricated with IBM90nm CMOS technology, and measurement results are presented to show the capability of wideband compressive sensing at sub-Nyquist rate. To the best of our knowledge, this prototype is the first reported integrated chip for wideband mixed-signal compressive sensing. The proposed prototype achieves 7 bits ENOB and 3 GS/s equivalent sampling rate in simulation assuming a 0.5 ps state-of-art jitter variance, whose FOM beats the FOM of the high speed state-of-the-art Nyquist ADCs by 2-3 times. The proposed mixed-signal compressive sensing system can be applied in various fields. In particular, its applications for wideband spectrum sensing for cognitive radios and spectrum analysis in RF tests are discussed in this work

High Speed Integrated Circuits for High Speed Coherent Optical Communications

With the development of (sub) THz transistor technologies, high speed integrated circuits up to sub-THz frequencies are now feasible. These high speed and wide bandwidth ICs can improve the performance of optical components, coherent optical fiber communication, and imaging systems. In current optical systems, electrical ICs are used primarily as driving amplifiers for optical modulators, and in receiver chains including TIAs, AGCs, LPFs, ADCs and DSPs. However, there are numerous potential applications in optics using high speed ICs, and different approaches may be required for more efficient, compact and flexible optical systems.This dissertation will discuss three different approaches for optical components and communication systems using high speed ICs: a homodyne optical phase locked loop (OPLL), a heterodyne OPLL, and a new WDM receiver architecture.The homodyne OPLL receiver is designed for short-link optical communication systems using coherent modulation for high spectral efficiency. The phase-locked coherent receiver can recover the transmitted data without requiring complex back-end digital signal processing to recover the phase of the received optical carrier. The main components of the homodyne OPLL are a photonic IC (PIC), an electrical IC (EIC), and a loop filter. One major challenge in OPLL development is loop bandwidth; this must be of order 1 GHz in order for the loop to adequately track and suppress the phase fluctuations of the locked laser, yet a 1 GHz loop bandwidth demands small (<100 ps) propagation delays if the loop is to be stable. Monolithic integration of the high-speed loop components into one electrical and one photonic IC decreases the total loop delay. We have designed and demonstrated an OPLL with a compact size of 10 × 10 mm2, stably operating with a loop bandwidth of 1.1 GHz, a loop delay of 120 ps, a pull-in time of 0.55 μs and lock time of <10 ns. The coherent receiver can receive 40 Gb/s BPSK data with a bit error rate (BER) of <10-7, and operates up to 35 Gb/s with BER 10-12.The thesis also describes heterodyne OPLLs. These can be used to synthesize optical wavelengths of a broad bandwidth (optical wavelength synthesis) with narrow linewidth and with fast frequency switching. There are many applications of such narrow linewidth optical signal sources, including low phase noise mm-wave and THz-signal sources, wavelength-division-multiplexed optical transmitters, and coherent imaging and sensor systems. The heterodyne OPLL also has the same stability issues (loop delay and sensitivity) as the homodyne OPLL. In the EIC, a single sideband mixer operating using digital design principles (DSSBM) enables precisely controlled sweeping of the frequency of the locked laser, with control of the sign of the frequency offset. The loop's phase and frequency difference detector (PFD) uses digital design techniques to make the OPLL loop parameters only weakly sensitive to optical signal levels or optical or electrical component gains. The heterodyne OPLL operates stably with a loop bandwidth of 550 MHz and loop delay of <200 ps. An initial OPLL design exhibited optical frequency (wavelength) synthesis from -6 GHz to -2 GHz and from 2 GHz to 9 GHz. An improved OPLL reached frequency tuning up to 25 GHz. The homodyne OPLL exhibits -110 dBc/Hz phase noise at 10 MHz offset and -80 dBc/Hz at 5 kHz offset.Finally, the thesis describes a new WDM receiver architecture using broadband electrical ICs. In the proposed WDM receiver, a set of received signals at different optical wavelengths are mixed against a single optical local oscillator. This mixing converts the WDM channels to electrical signals in the receiver photocurrent, with each WDM signal being converted to an RF sub-carrier of different frequency. An electrical IC then separately converts each sub-carrier signal to baseband using single-sideband mixers and quadrature local oscillators. The proposed receiver needs less complex hardware than the arrays of wavelength-sensitive receivers now used for WDM, and can readily adjust to changes in the WDM channel frequencies. The proposed WDM receiver concept was demonstrated through several system experiments. Image rejection of greater than 25 dB, adjacent channel suppression of greater than 20 dB, operation with gridless channels, and six-channel data reception at a total 15 Gb/s (2.5 Gb/s BPSK × 6-channels) were demonstrated

Third International Symposium on Space Mission Operations and Ground Data Systems, part 1

Under the theme of 'Opportunities in Ground Data Systems for High Efficiency Operations of Space Missions,' the SpaceOps '94 symposium included presentations of more than 150 technical papers spanning five topic areas: Mission Management, Operations, Data Management, System Development, and Systems Engineering. The papers focus on improvements in the efficiency, effectiveness, productivity, and quality of data acquisition, ground systems, and mission operations. New technology, techniques, methods, and human systems are discussed. Accomplishments are also reported in the application of information systems to improve data retrieval, reporting, and archiving; the management of human factors; the use of telescience and teleoperations; and the design and implementation of logistics support for mission operations

Analysis and Design of Energy Efficient Frequency Synthesizers for Wireless Integrated Systems

Advances in ultra-low power (ULP) circuit technologies are expanding the IoT applications in our daily life. However, wireless connectivity, small form factor and long lifetime are still the key constraints for many envisioned wearable, implantable and maintenance-free monitoring systems to be practically deployed at a large scale. The frequency synthesizer is one of the most power hungry and complicated blocks that not only constraints RF performance but also offers subtle scalability with power as well. Furthermore, the only indispensable off-chip component, the crystal oscillator, is also associated with the frequency synthesizer as a reference. This thesis addresses the above issues by analyzing how phase noise of the LO affect the frequency modulated wireless system in different aspects and how different noise sources in the PLL affect the performance. Several chip prototypes have been demonstrated including: 1) An ULP FSK transmitter with SAR assisted FLL; 2) A ring oscillator based all-digital BLE transmitter utilizing a quarter RF frequency LO and 4X frequency multiplier; and 3) An XO-less BLE transmitter with an RF reference recovery receiver. The first 2 designs deal with noise sources in the PLL loop for ultimate power and cost reduction, while the third design deals with the reference noise outside the PLL and explores a way to replace the XO in ULP wireless edge nodes. And at last, a comprehensive PN theory is proposed as the design guideline.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/153420/1/chenxing_1.pd

Shuttle Communications and Tracking Systems Modeling and TDRSS Link Simulations Studies

An analytical simulation package (LinCsim) which allows the analytical verification of data transmission performance through TDRSS satellites was modified. The work involved the modeling of the user transponder, TDRS, TDRS ground terminal, and link dynamics for forward and return links based on the TDRSS performance specifications (4) and the critical design reviews. The scope of this effort has recently been expanded to include the effects of radio frequency interference (RFI) on the bit error rate (BER) performance of the S-band return links. The RFI environment and the modified TDRSS satellite and ground station hardware are being modeled in accordance with their description in the applicable documents