Analysis and application of digital spectral warping in analog and mixed-signal testing

Spectral warping is a digital signal processing transform which shifts the frequencies contained within a signal along the frequency axis. The Fourier transform coefficients of a warped signal correspond to frequency-domain 'samples' of the original signal which are unevenly spaced along the frequency axis. This property allows the technique to be efficiently used for DSP-based analog and mixed-signal testing. The analysis and application of spectral warping for test signal generation, response analysis, filter design, frequency response evaluation, etc. are discussed in this paper along with examples of the software and hardware implementation

Measurement of interface pressure in interference fits

When components such as bearings or gears are pressed onto a shaft, the resulting interference induces a pressure at the interface. The size of this pressure is important as many components fail because fatigue initiates from press-fit stress concentrations. The aim of the present work was to develop ultrasound as a tool for non-destructive determination of press-fit contact pressures. An interference fit interface behaves like a spring. If the pressure is high, there are few air gaps, so it is very stiff and allows transmission of an ultrasonic wave. If the pressure is low, then interface stiffness is lower and most ultrasound is reflected. A spring model was used to determine maps of contact stiffness from interference-fit ultrasonic reflection data. A calibration procedure was then used to determine the pressure. The interface contact pressure has been determined for a number of different press- and shrink-fit cases. The results show a central region of approximately uniform pressure with edge stress at the contact sides. The magnitude of the pressure in the central region agrees well with the elastic Lamé analysis. In the more severe press-fit cases, the surfaces scuffed which led to anomalies in the reflected ultrasound. These anomalies were associated with regions of surface damage at the interface. The average contact pressure in a shrink-fit and press-fit joint were similar. However, in the shrink-fit joint more uneven contact pressure was observed with regions of poor conformity. This could be because the action of pressing on a sleeve plastically smooths out long wavelength roughness, leading to a more conforming surface

A Feature Learning Siamese Model for Intelligent Control of the Dynamic Range Compressor

In this paper, a siamese DNN model is proposed to learn the characteristics of the audio dynamic range compressor (DRC). This facilitates an intelligent control system that uses audio examples to configure the DRC, a widely used non-linear audio signal conditioning technique in the areas of music production, speech communication and broadcasting. Several alternative siamese DNN architectures are proposed to learn feature embeddings that can characterise subtle effects due to dynamic range compression. These models are compared with each other as well as handcrafted features proposed in previous work. The evaluation of the relations between the hyperparameters of DNN and DRC parameters are also provided. The best model is able to produce a universal feature embedding that is capable of predicting multiple DRC parameters simultaneously, which is a significant improvement from our previous research. The feature embedding shows better performance than handcrafted audio features when predicting DRC parameters for both mono-instrument audio loops and polyphonic music pieces.Comment: 8 pages, accepted in IJCNN 201

A Hybrid Parameterization Technique for Speaker Identification

Classical parameterization techniques for Speaker Identification use the codification of the power spectral density of raw speech, not discriminating between articulatory features produced by vocal tract dynamics (acoustic-phonetics) from glottal source biometry. Through the present paper a study is conducted to separate voicing fragments of speech into vocal and glottal components, dominated respectively by the vocal tract transfer function estimated adaptively to track the acoustic-phonetic sequence of the message, and by the glottal characteristics of the speaker and the phonation gesture. The separation methodology is based in Joint Process Estimation under the un-correlation hypothesis between vocal and glottal spectral distributions. Its application on voiced speech is presented in the time and frequency domains. The parameterization methodology is also described. Speaker Identification experiments conducted on 245 speakers are shown comparing different parameterization strategies. The results confirm the better performance of decoupled parameterization compared against approaches based on plain speech parameterization

Diesel engine fuel injection monitoring using acoustic measurements and independent component analysis

Air-borne acoustic based condition monitoring is a promising technique because of its intrusive nature and the rich information contained within the acoustic signals including all sources. However, the back ground noise contamination, interferences and the number of Internal Combustion Engine ICE vibro-acoustic sources preclude the extraction of condition information using this technique. Therefore, lower energy events; such as fuel injection, are buried within higher energy events and/or corrupted by background noise. This work firstly investigates diesel engine air-borne acoustic signals characteristics and the benefits of joint time-frequency domain analysis. Secondly, the air-borne acoustic signals in the vicinity of injector head were recorded using three microphones around the fuel injector (120° apart from each other) and an Independent Component Analysis (ICA) based scheme was developed to decompose these acoustic signals. The fuel injection process characteristics were thus revealed in the time-frequency domain using Wigner-Ville distribution (WVD) technique. Consequently the energy levels around the injection process period between 11 and 5 degrees before the top dead center and of frequency band 9 to 15 kHz are calculated. The developed technique was validated by simulated signals and empirical measurements at different injection pressure levels from 250 to 210 bars in steps of 10 bars. The recovered energy levels in the tested conditions were found to be affected by the injector pressure settings