86 research outputs found
Design and control of a bio-inspired soft wearable robotic device for ankle-foot rehabilitation
Abstract We describe the design and control of a wearable robotic device powered by pneumatic artificial muscle actuators for use in ankle-foot rehabilitation. The design is inspired by the biological musculoskeletal system of the human foot and lower leg, mimicking the morphology and the functionality of the biological muscle-tendon-ligament structure. A key feature of the device is its soft structure that provides active assistance without restricting natural degrees of freedom at the ankle joint. Four pneumatic artificial muscles assist dorsiflexion and plantarflexion as well as inversion and eversion. The prototype is also equipped with various embedded sensors for gait pattern analysis. For the subject tested, the prototype is capable of generating an ankle range of motion of 27 âą (14 âą dorsiflexion and 13 âą plantarflexion). The controllability of the system is experimentally demonstrated using a linear time-invariant (LTI) controller. The controller is found using an identified LTI model of the system, resulting from the interaction of the soft orthotic device with a human leg, and model-based classical control design techniques. The suitability of the proposed control strategy is demonstrated with several angle-reference following experiments
Application of wearable sensors in actuation and control of powered ankle exoskeletons: a Comprehensive Review
Powered ankle exoskeletons (PAEs) are robotic devices developed for gait assistance, rehabilitation, and augmentation. To fulfil their purposes, PAEs vastly rely heavily on their sensor systems. Humanâmachine interface sensors collect the biomechanical signals from the human user to inform the higher level of the control hierarchy about the userâs locomotion intention and requirement, whereas machineâmachine interface sensors monitor the output of the actuation unit to ensure precise tracking of the high-level control commands via the low-level control scheme. The current article aims to provide a comprehensive review of how wearable sensor technology has contributed to the actuation and control of the PAEs developed over the past two decades. The control schemes and actuation principles employed in the reviewed PAEs, as well as their interaction with the integrated sensor systems, are investigated in this review. Further, the role of wearable sensors in overcoming the main challenges in developing fully autonomous portable PAEs is discussed. Finally, a brief discussion on how the recent technology advancements in wearable sensors, including environmentâmachine interface sensors, could promote the future generation of fully autonomous portable PAEs is provided
Pneumatic ergonomic crutches
Long-term crutch users utilize Lofstrand crutches for locomotion commonly using swing-through or reciprocal gait patterns. Repetitive high forces, hyperextension and ulnar deviation of the wrist, and excessive palmar pressure compressing the median nerve associated with crutch walking have reported to cause discomfort, joint pain, wrist strain, carpal tunnel syndrome and other serious injuries. To address these issues, we developed the pneumatic ergonomic crutches (PEC) that consisted of a pneumatic sleeve orthosis, an energy harvesting system and an energy storage system. The pneumatic sleeve orthosis utilized a soft pneumatic actuator, called fiber-reinforced elastomeric enclosure, coiled around the forearm and secured to the cuff. In the first study, sleeve orthosis performance was examined. Human subject testing indicated significantly improved wrist posture, increased loading sharing to the cuff, reduced and redirected palmar pressure while using the orthosis. In the second study, the fully-developed PEC was presented. The PEC utilized an energy harvesting piston pump to collect pneumatic energy during crutch gait. The collected pneumatic energy was stored into a pneumatic elastomeric accumulator (PEA) inside the crutch shaft, which can be used to inflate the sleeve orthosis to make a self-contained crutch system. We optimized dimensions and specifications of the piston pump and the PEA to minimize the number of gait cycles used to charge the PEA to a target pressure that can be used to fully charge the sleeve orthosis. Bench-top testing was conducted on the PEC and demonstrated the ability of charging the sleeve orthosis using air stored in the PEA after 38 gait cycles. Protocols for future human subject testing to evaluate the system performance of the PEC were also presented
Design and Evaluation of AIRGAIT Exoskeleton\u27s Leg Orthosis: Development of a Control Scheme and Strategy for a Noble Control of Antagonistic Mono- and Bi-Articular Actuators
èæ”Šć·„æ„性ćŠ201
Design Principles for FES Concept Development
© Cranfield University 2013. All rights reserved. No part of this
publication may be reproduced without the written permission of the
copyright owner.A variety of pathologies can cause injury to the spinal cord and hinder movement. A range of
equipment is available to help spinal injury sufferers move their affected limbs. One method of
rehabilitation is functional electrical stimulation (FES). FES is a technique where small electrical
currents are applied to the surface of the userâs legs to stimulate the muscles. Studies have
demonstrated the benefits of using this method and it has also been incorporated into a
number of devices.
The aim of the project was to produce a number of designs for a new device that uses FES
technology. The project was completed in conjunction with an industrial partner. A review of
the literature and consultation with industrial experts suggested a number of ways current
devices could be improved. These included encouraging the user to lean forwards while
walking and powering the device using a more ergonomic method.
A group of designers were used to produce designs that allowed the user to walk with a more
natural gait and avoided cumbersome power packs. The most effective of these designs were
combined to form one design that solved both problems. A 3-dimensional model of this design
was simulated using computer-aided design software.
Groups of engineers, scientists and consumers were also invited to provide input on how a
new device should function. Each of these groups provided a design that reflected their
specific needs, depending on their experience with similar technology. Low level prototypes
were produced of these designs.
A group of designers were also used to design concepts for a functional electrical stimulation
device based on an introduction given by industry experts.
Each of the designs was presented to experienced professionals to obtain feedback.
A set of guidelines were also produced during the project that instructed how to create the
designs
Physical human-robot collaboration: Robotic systems, learning methods, collaborative strategies, sensors, and actuators
This article presents a state-of-the-art survey on the robotic systems, sensors, actuators, and collaborative strategies for physical human-robot collaboration (pHRC). This article starts with an overview of some robotic systems with cutting-edge technologies (sensors and actuators) suitable for pHRC operations and the intelligent assist devices employed in pHRC. Sensors being among the essential components to establish communication between a human and a robotic system are surveyed. The sensor supplies the signal needed to drive the robotic actuators. The survey reveals that the design of new generation collaborative robots and other intelligent robotic systems has paved the way for sophisticated learning techniques and control algorithms to be deployed in pHRC. Furthermore, it revealed the relevant components needed to be considered for effective pHRC to be accomplished. Finally, a discussion of the major advances is made, some research directions, and future challenges are presented
- âŠ