Analysis and practical considerations in implementing multiple transmitters and receivers for wireless power transfer via coupled magnetic resonance

The technology to wirelessly power mobile devices has started to gain momentum especially in industry. Cables have started to become the thing of the past as both wireless power efficiency and communication speeds become viably attractive. The first part of this work gives analysis and practical considerations in implementing multiple transmitters for wireless power transfer via coupled magnetic resonance. Through the multiple transmitter scheme, there is an increase in gain and `diversity\u27 of the transmitted power according to the number of transmit coils. The effect of transmitter resonant coil coupling is also shown. Resonant frequency detuning due to nearby metallic objects is observed and the extent of how much tuning can be done is demonstrated. A practical power line synchronization technique is proposed to synchronize all transmit coils. This reduces additional dedicated synchronization wiring or the addition of an RF front end module. The second part of this study introduces a time division multiplexing (TDM) technique for tightly coupled receivers via the same method of coupled magnetic resonance. Two or more receivers can be powered simultaneously using a single transmit coil. In a tightly coupled receiver scenario, the received power is significantly reduced. Experimental and simulation results implementing TDM show vast improvements in received power in the tightly coupled case. Resonant frequency splitting is eliminated through synchronized detuning between receivers, which divide power equally between receivers at specific time slots. The last chapter gives insight on the capacity of a single-input single-output system at varying distances between receiver and transmitter. It is shown that the highest information rate is achieved at critical coupling

The impact of Nodes Distance on Wireless Energy Transfer System

Wireless energy transfer (WET) reemerges as the method for transmitting electric power without the necessity to deal with cable losses and an aesthetically pleasing environment. The problem with WET is how to maintain magnetic induction as the distance gets further. This paper investigates the impact of nodes distance on the WET system. The experimental results show that the most effective distance among transmitter, nodes, and receiver are 4 cm. The measurement is taken with and without load. The without load application give that for node 1; the results are 6 V, 110 mA, and 2.85 mT for voltage, current, and magnetic flux, respectively. At the application of 2 nodes, the voltage is 6.8 V, the current is 0.124 mA, and the magnetic flux is 3.83 mT, and at three nodes installation, it is 7 V, 134 mA, and 3.83 mT. During the application of 3-Watt and 5-Watt lamp, at 4 cm distance, the power received is 1.66 W and 3.66 W at 3-Watt and 5-Watt lamp for one node, 1.84 W, and 3.84 for two nodes, and 1.93 W and 3.93 for three nodes. The experimental results show that the transmitted signal can be prolonged by installing nodes. Even though this study shows that 4 cm is the most effective, it is possible to increase up to 20 cm to power a 3-Watt lamp and 5-Watt lamp

Wireless Power Transfer

Wireless power transfer techniques have been gaining researchers' and industry attention due to the increasing number of battery-powered devices, such as mobile computers, mobile phones, smart devices, intelligent sensors, mainly as a way to replace the standard cable charging, but also for powering battery-less equipment. The storage capacity of batteries is an extremely important element of how a device can be used. If we talk about battery-powered electronic equipment, the autonomy is one factor that may be essential in choosing a device or another, making the solution of remote powering very attractive. A distinction has to be made between the two forms of wireless power transmission, as seen in terms of how the transmitted energy is used at the receiving point: - Transmission of information or data, when it is essential for an amount of energy to reach the receiver to restore the transmitted information; - Transmission of electric energy in the form of electromagnetic field, when the energy transfer efficiency is essential, the power being used to energize the receiving equipment. The second form of energy transfer is the subject of this book

Frequency reliant wireless power transfer link for a applications of mWatts devices

In general, the resonant inductive wireless power transfer is superior in power efficiency consequently provides longer transfer range over inductive or capacitive wireless power transfer. For that reason, the theoretical analysis and simulation results of the series-to-series wireless power transfer topology were discussed in this paper. The study is conducted to analyze the effect of the coupling coefficient (k) of the coupling coils to the resonant frequency and input impedance of the transmitting circuit. The analysis is conducted by analyzing the equivalent circuit model by using circuit theory. The equivalent circuit model is developed by using the T-equivalent circuit. Further, the result is validated with the circuit simulation using the ISIS Proteus simulation package. The results of the analysis used in developing the highly efficient series-to-series wireless power transfer

High-performance wireless power and data transfer interface for implantable medical devices

D’importants progès ont été réalisés dans le développement des systèmes biomédicaux implantables grâce aux dernières avancées de la microélectronique et des technologies sans fil. Néanmoins, ces appareils restent difficiles à commercialier. Cette situation est due particulièrement à un manque de stratégies de design capable supporter les fonctionnalités exigées, aux limites de miniaturisation, ainsi qu’au manque d’interface sans fil à haut débit fiable et faible puissance capable de connecter les implants et les périphériques externes. Le nombre de sites de stimulation et/ou d’électrodes d’enregistrement retrouvés dans les dernières interfaces cerveau-ordinateur (IMC) ne cesse de croître afin d’augmenter la précision de contrôle, et d’améliorer notre compréhension des fonctions cérébrales. Ce nombre est appelé à atteindre un millier de site à court terme, ce qui exige des débits de données atteingnant facilement les 500 Mbps. Ceci étant dit, ces travaux visent à élaborer de nouvelles stratégies innovantes de conception de dispositifs biomédicaux implantables afin de repousser les limites mentionnées ci-dessus. On présente de nouvelles techniques faible puissance beaucoup plus performantes pour le transfert d’énergie et de données sans fil à haut débit ainsi que l’analyse et la réalisation de ces dernières grâce à des prototypes microélectroniques CMOS. Dans un premier temps, ces travaux exposent notre nouvelle structure multibobine inductive à résonance présentant une puissance sans fil distribuée uniformément pour alimenter des systèmes miniatures d’étude du cerveaux avec des models animaux en ilberté ainsi que des dispositifs médicaux implantbles sans fil qui se caractérisent par une capacité de positionnement libre. La structure propose un lien de résonance multibobines inductive, dont le résonateur principal est constitué d’une multitude de résonateurs identiques disposés dans une matrice de bobines carrées. Ces dernières sont connectées en parallèle afin de réaliser des surfaces de puissance (2D) ainsi qu’une chambre d’alimentation (3D). La chambre proposée utilise deux matrices de résonateurs de base, mises face à face et connectés en parallèle afin d’obtenir une distribution d’énergie uniforme en 3D. Chaque surface comprend neuf bobines superposées, connectées en parallèle et réailsées sur une carte de circuit imprimé deux couches FR4. La chambre dispose d’un mécanisme naturel de localisation de puissance qui facilite sa mise en oeuvre et son fonctionnement. En procédant ainsi, nous évitons la nécessité d’une détection active de l’emplacement de la charge et le contrôle d’alimentation. Notre approche permet à cette surface d’alimentation unique de fournir une efficacité de transfert de puissance (PTE) de 69% et une puissance délivrée à la charge (PDL) de 120 mW, pour une distance de séparation de 4 cm, tandis que le prototype de chambre complet fournit un PTE uniforme de 59% et un PDL de 100 mW en 3D, partout à l’intérieur de la chambre avec un volume de chambre de 27 × 27 × 16 cm3. Une étape critique avant d’utiliser un dispositif implantable chez les humains consiste à vérifier ses fonctionnalités sur des sujets animaux. Par conséquent, la chambre d’énergie sans fil conçue sera utilisée afin de caractériser les performances d’ une interface sans fil de transmisison de données dans un environnement réaliste in vivo avec positionement libre. Un émetteur-récepteur full-duplex (FDT) entièrement intégré qui se caractérise par sa faible puissance est conçu pour réaliser une interfaces bi-directionnelles (stimulation et enregistrement) avec des débits asymétriques: des taux de tramnsmission plus élevés sont nécessaires pour l’enregistrement électrophysiologique multicanal (signaux de liaison montante) alors que les taux moins élevés sont utilisés pour la stimulation (les signaux de liaison descendante). L’émetteur (TX) et le récepteur (RX) se partagent une seule antenne afin de réduire la taille de l’implant. L’émetteur utilise la radio ultra-large bande par impulsions (IR-UWB) basée sur l’approche edge combining et le RX utilise la bande ISM (Industrielle, Scientifique et Médicale) de fréquence central 2.4 GHz et la modulation on-off-keying (OOK). Une bonne isolation (> 20 dB) est obtenue entre le TX et le RX grâce à 1) la mise en forme les impulsions émises dans le spectre UWB non réglementée (3.1-7 GHz), et 2) le filtrage espace-efficace (évitant l’utilisation d’un circulateur ou d’un diplexeur) du spectre du lien de communication descendant directement au niveau de l’ amplificateur à faible bruit (LNA). L’émetteur UWB 3.1-7 GHz utilise un e modultion OOK ainsi qu’une modulation par déplacement de phase (BPSK) à seulement 10.8 pJ / bits. Le FDT proposé permet d’atteindre 500 Mbps de débit de données en lien montant et 100 Mbps de débit de données de lien descendant. Il est entièrement intégré dans un procédé TSMC CMOS 0.18 um standard et possède une taille totale de 0.8 mm2. La consommation totale d’énergie mesurée est de 10.4 mW (5 mW pour RX et 5.4 mW pour TX au taux de 500 Mbps).In recent years, there has been major progress on implantable biomedical systems that support most of the functionalities of wireless implantable devices. Nevertheless, these devices remain mostly restricted to be commercialized, in part due to weakness of a straightforward design to support the required functionalities, limitation on miniaturization, and lack of a reliable low-power high data rate interface between implants and external devices. This research provides novel strategies on the design of implantable biomedical devices that addresses these limitations by presenting analysis and techniques for wireless power transfer and efficient data transfer. The first part of this research includes our proposed novel resonance-based multicoil inductive power link structure with uniform power distribution to wirelessly power up smart animal research systems and implanted medical devices with high power efficiency and free positioning capability. The proposed structure consists of a multicoil resonance inductive link, which primary resonator array is made of several identical resonators enclosed in a scalable array of overlapping square coils that are connected in parallel and arranged in power surface (2D) and power chamber (3D) configurations. The proposed chamber uses two arrays of primary resonators, facing each other, and connected in parallel to achieve uniform power distribution in 3D. Each surface includes 9 overlapped coils connected in parallel and implemented into two layers of FR4 printed circuit board. The chamber features a natural power localization mechanism, which simplifies its implementation and eases its operation by avoiding the need for active detection of the load location and power control mechanisms. A single power surface based on the proposed approach can provide a power transfer efficiency (PTE) of 69% and a power delivered to the load (PDL) of 120 mW, for a separation distance of 4 cm, whereas the complete chamber prototype provides a uniform PTE of 59% and a PDL of 100 mW in 3D, everywhere inside the chamber with a chamber size of 27×27×16 cm3. The second part of this research includes our proposed novel, fully-integrated, low-power fullduplex transceiver (FDT) to support bi-directional neural interfacing applications (stimulating and recording) with asymmetric data rates: higher rates are required for recording (uplink signals) than stimulation (downlink signals). The transmitter (TX) and receiver (RX) share a single antenna to reduce implant size. The TX uses impulse radio ultra-wide band (IR-UWB) based on an edge combining approach, and the RX uses a novel 2.4-GHz on-off keying (OOK) receiver. Proper isolation (> 20 dB) between the TX and RX path is implemented 1) by shaping the transmitted pulses to fall within the unregulated UWB spectrum (3.1-7 GHz), and 2) by space-efficient filtering (avoiding a circulator or diplexer) of the downlink OOK spectrum in the RX low-noise amplifier (LNA). The UWB 3.1-7 GHz transmitter using OOK and binary phase shift keying (BPSK) modulations at only 10.8 pJ/bit. The proposed FDT provides dual band 500 Mbps TX uplink data rate and 100 Mbps RX downlink data rate. It is fully integrated on standard TSMC 0.18 nm CMOS within a total size of 0.8 mm2. The total power consumption measured 10.4 mW (5 mW for RX and 5.4 mW for TX at the rate of 500 Mbps)

Wireless Technologies for Implantable Devices

Wireless technologies are incorporated in implantable devices since at least the 1950s. With remote data collection and control of implantable devices, these wireless technologies help researchers and clinicians to better understand diseases and to improve medical treatments. Today, wireless technologies are still more commonly used for research, with limited applications in a number of clinical implantable devices. Recent development and standardization of wireless technologies present a good opportunity for their wider use in other types of implantable devices, which will significantly improve the outcomes of many diseases or injuries. This review briefly describes some common wireless technologies and modern advancements, as well as their strengths and suitability for use in implantable medical devices. The applications of these wireless technologies in treatments of orthopedic and cardiovascular injuries and disorders are described. This review then concludes with a discussion on the technical challenges and potential solutions of implementing wireless technologies in implantable devices

Secondary-Side Control in Dynamic Wireless Power Transfer Systems for Double-Sided Inductor-Capacitor-Capacitor and Series-Series Compensation Topologies

Electric Vehicles (EVs) are fast becoming a great alternative as future mode of transportation, due to their promise of low emissions. Nevertheless, EVs suffer from battery related problems such as large size, heavy weight, high price, long charging times and a short driving range. Dynamic wireless power transfer systems (DWPTSs) address the battery issue by providing power to the vehicle while in motion, and eliminate the need of plugging. However, unavoidable load and coupling coefficient variations cause degradation of power delivery and efficiency. Hence, a controller must be added to the dynamic charger for power conditioning and efficiency enhancement. This project is focused on the control stage of the DWPTS adopting a post-regulation scheme as control strategy. It proposes the integration of a secondary-side-only control under double-sided inductor-capacitor-capacitor (LCC) and series-series compensation topologies. A synchronous buck converter is used to step down the voltage to the maximum power transfer efficiency (MPTE) conditions and control the direct current (DC) link by adjusting the duty cycle of the control pulse. Averaged alternating current (AC) modelling is applied for designing the controller to smooth and speed the response of both systems. An estimation equation for coupling coefficient and a controller for the double-sided LCC compensation topology are introduced. A comparison study between these two topologies comprised of their characteristics and response to the controller is carried out

Frequency splitting elimination and cross-coupling rejection of wireless power transfer to multiple dynamic receivers

Simultaneous power transfer to multiple receiver (Rx) system is one of the key advantages of wireless power transfer (WPT) system using magnetic resonance. However, determining the optimal condition to uniformly transfer the power to a selected Rx at high efficiency is the challenging task under the dynamic environment. The cross-coupling and frequency splitting are the dominant issues present in the multiple Rx dynamic WPT system. The existing analysis is performed by considering any one issue present in the system; on the other hand, the cross coupling and frequency splitting issues are interrelated in dynamic Rx’s, which requires a comprehensive design strategy by considering both the problems. This paper proposes an optimal design of multiple Rx WPT system, which can eliminate cross coupling, frequency splitting issues and increase the power transfer efficiency (PTE) of selected Rx. The cross-coupling rejection, uniform power transfer is performed by adding an additional relay coil and independent resonance frequency tuning with capacitive compensation to each Rx unit. The frequency splitting phenomena are eliminated using non-identical transmitter (Tx) and Rx coil structure which can maintain the coupling between the coil under the critical coupling limit. The mathematical analysis of the compensation capacitance calculation and optimal Tx coil size identification is performed for the four Rx WPT system. Finite element analysis and experimental investigation are carried out for the proposed design in static and dynamic conditions