An Adaptive Iterative Learning Control for Robot Manipulator in Task Space

In this paper, adaptive iterative learning control (AILC) of uncertain robot manipulators in task space is considered for trajectory tracking in an iterative operation mode. The control scheme incluces a PD controller with a gain switching technique plus a learning feedforward term, is exploited to predict the desired actuator torque. By using Lyapunov method, an adaptive iterative learning control scheme is presented for robotic system with both structured and unstructured uncertainty, and the overall stability of the closed-loop system in the iterative domain is established. The validity of the scheme is confirmed through a numerical simulation

Hybrid iterative learning control of a flexible manipulator

This paper presents an investigation into the development of a hybrid control scheme with iterative learning for input tracking and end-point vibration suppression of a flexible manipulator system. The dynamic model of the system is derived using the finite element method. Initially, a collocated proportional-derivative (PD) controller using hub angle and hub velocity feedback is developed for control of rigid-body motion of the system. This is then extended to incorporate a non-collocated proportional-integral-derivative (PID) controller with iterative learning for control of vibration of the system. Simulation results of the response of the manipulator with the controllers are presented in the time and frequency domains. The performance of the hybrid iterative learning control scheme is assessed in terms of input tracking and level of vibration reduction in comparison to a conventionally designed PD-PID control scheme. The effectiveness of the control scheme in handling various payloads is also studied

Performance improvement of robots using a learning control scheme

Many applications of robots require that the same task be repeated a number of times. In such applications, the errors associated with one cycle are also repeated every cycle of the operation. An off-line learning control scheme is used here to modify the command function which would result in smaller errors in the next operation. The learning scheme is based on a knowledge of the errors and error rates associated with each cycle. Necessary conditions for the iterative scheme to converge to zero errors are derived analytically considering a second order servosystem model. Computer simulations show that the errors are reduced at a faster rate if the error rate is included in the iteration scheme. The results also indicate that the scheme may increase the magnitude of errors if the rate information is not included in the iteration scheme. Modification of the command input using a phase and gain adjustment is also proposed to reduce the errors with one attempt. The scheme is then applied to a computer model of a robot system similar to PUMA 560. Improved performance of the robot is shown by considering various cases of trajectory tracing. The scheme can be successfully used to improve the performance of actual robots within the limitations of the repeatability and noise characteristics of the robot

Reconstructing null-space policies subject to dynamic task constraints in redundant manipulators

We consider the problem of direct policy learning in situations where the policies are only observable through their projections into the null-space of a set of dynamic, non-linear task constraints. We tackle the issue of deriving consistent data for the learning of such policies and make two contributions towards its solution. Firstly, we derive the conditions required to exactly reconstruct null-space policies and suggest a learning strategy based on this derivation. Secondly, we consider the case that the null-space policy is conservative and show that such a policy can be learnt more easily and robustly by learning the underlying potential function and using this as our representation of the policy.

Experimental study of trajectory planning and control of a high precision robot manipulator

The kinematic and trajectory planning is presented for a 6 DOF end-effector whose design was based on the Stewart Platform mechanism. The end-effector was used as a testbed for studying robotic assembly of NASA hardware with passive compliance. Vector analysis was employed to derive a closed-form solution for the end-effector inverse kinematic transformation. A computationally efficient numerical solution was obtained for the end-effector forward kinematic transformation using Newton-Raphson method. Three trajectory planning schemes, two for fine motion and one for gross motion, were developed for the end-effector. Experiments conducted to evaluate the performance of the trajectory planning schemes showed excellent tracking quality with minimal errors. Current activities focus on implementing the developed trajectory planning schemes on mating and demating space-rated connectors and using the compliant platform to acquire forces/torques applied on the end-effector during the assembly task

Model-Based Iterative Learning Control Applied to an Industrial Robot with Elasticity

In this paper model-based Iterative Learning Control (ILC) is applied to improve the tracking accuracy of an industrial robot with elasticity. The ILC algorithm iteratively updates the reference trajectory for the robot such that the predicted tracking error in the next iteration is minimised. The tracking error is predicted by a model of the closed-loop dynamics of the robot. The model includes the servo resonance frequency, the first resonance frequency caused by elasticity in the mechanism and the variation of both frequencies along the trajectory. Experimental results show that the tracking error of the robot can be reduced, even at frequencies beyond the first elastic resonance frequency