Improved Spectrum Usage with Multi-RF Channel Aggregation Technologies for the Next-Generation Terrestrial Broadcasting

[EN] Next-generation terrestrial broadcasting targets at enhancing spectral efficiency to overcome the challenges derived from the spectrum shortage as a result of the progressive allocation of frequencies - the so-called Digital Dividend - to satisfy the growing demands for wireless broadband capacity. Advances in both transmission standards and video coding are paramount to enable the progressive roll-out of high video quality services such as HDTV (High Definition Televison) or Ultra HDTV. The transition to the second generation European terrestrial standard DVB-T2 and the introduction of MPEG-4/AVC video coding already enables the transmission of 4-5 HDTV services per RF (Radio Frequency) channel. However, the impossibility to allocate higher bit-rate within the remaining spectrum could jeopardize the evolution of the DTT platforms in favour of other high-capacity systems such as the satellite or cable distribution platforms. Next steps are focused on the deployment of the recently released High Efficiency Video Coding (HEVC) standard, which provides more than 50% coding gain with respect to AVC, with the next-generation terrestrial standards. This could ensure the competitiveness of the DTT. This dissertation addresses the use of multi-RF channel aggregation technologies to increase the spectral efficiency of future DTT networks. The core of the Thesis are two technologies: Time Frequency Slicing (TFS) and Channel Bonding (CB). TFS and CB consist in the transmission of the data of a TV service across multiple RF channels instead of using a single channel. CB spreads data of a service over multiple classical RF channels (RF-Mux). TFS spreads the data by time-slicing (slot-by-slot) across multiple RF channels which are sequentially recovered at the receiver by frequency hopping. Transmissions using these features can benefit from capacity and coverage gains. The first one comes from a more efficient statistical multiplexing (StatMux) for Variable Bit Rate (VBR) services due to a StatMux pool over a higher number of services. Furthermore, CB allows increasing service data rate with the number of bonded RF channels and also advantages when combined with SVC (Scalable Video Coding). The coverage gain comes from the increased RF performance due to the reception of the data of a service from different RF channels rather that a single one that could be, eventually, degraded. Robustness against interferences is also improved since the received signal does not depend on a unique potentially interfered RF channel. TFS was firstly introduced as an informative annex in DVB-T2 (not normative) and adopted in DVB-NGH (Next Generation Handheld). TFS and CB are proposed for inclusion in ATSC 3.0. However, they have never been implemented. The investigations carried out in this dissertation employ an information-theoretical approach to obtain their upper bounds, physical layer simulations to evaluate the performance in real systems and the analysis of field measurements that approach realistic conditions of the network deployments. The analysis report coverage gains about 4-5 dB with 4 RF channels and high capacity gains already with 2 RF channels. This dissertation also focuses on implementation aspects. Channel bonding receivers require one tuner per bonded RF channel. The implementation of TFS with a single tuner demands the fulfilment of several timing requirements. However, the use of just two tuners would still allow for a good performance with a cost-effective implementation by the reuse of existing chipsets or the sharing of existing architectures with dual tuner operation such as MIMO (Multiple Input Multiple Output).[ES] La televisión digital terrestre (TDT) de última generación está orientada a una necesaria mejora de la eficiencia espectral con el fin de abordar los desafíos derivados de la escasez de espectro como resultado de la progresiva asignación de frecuencias - el llamado Dividendo Digital - para satisfacer la creciente demanda de capacidad para la banda ancha inalámbrica. Los avances tanto en los estándares de transmisión como de codificación de vídeo son de suma importancia para la progresiva puesta en marcha de servicios de alta calidad como la televisión de Ultra AD (Alta Definición). La transición al estándar europeo de segunda generación DVB-T2 y la introducción de la codificación de vídeo MPEG-4 / AVC ya permite la transmisión de 4-5 servicios de televisión de AD por canal RF (Radiofrecuencia). Sin embargo, la imposibilidad de asignar una mayor tasa de bit sobre el espectro restante podría poner en peligro la evolución de las plataformas de TDT en favor de otros sistemas de alta capacidad tales como el satélite o las distribuidoras de cable. El siguiente paso se centra en el despliegue del reciente estándar HEVC (High Efficiency Video Coding), que ofrece un 50% de ganancia de codificación con respecto a AVC, junto con los estándares terrestres de próxima generación, lo que podría garantizar la competitividad de la TDT en un futuro cercano. Esta tesis aborda el uso de tecnologías de agregación de canales RF que permitan incrementar la eficiencia espectral de las futuras redes. La tesis se centra en torno a dos tecnologías: Time Frequency Slicing (TFS) y Channel Bonding (CB). TFS y CB consisten en la transmisión de los datos de un servicio de televisión a través de múltiples canales RF en lugar de utilizar un solo canal. CB difunde los datos de un servicio a través de varios canales RF convencionales formando un RF-Mux. TFS difunde los datos a través de ranuras temporales en diferentes canales RF. Los datos son recuperados de forma secuencial en el receptor mediante saltos en frecuencia. La implementación de estas técnicas permite obtener ganancias en capacidad y cobertura. La primera de ellas proviene de una multiplexación estadística (StatMux) de servicios de tasa variable (VBR) más eficiente. Además, CB permite aumentar la tasa de pico de un servicio de forma proporcional al número de canales así como ventajas al combinarla con codificación de vídeo escalable. La ganancia en cobertura proviene de un mejor rendimiento RF debido a la recepción de los datos de un servicio desde diferentes canales en lugar uno sólo que podría estar degradado. Del mismo modo, es posible obtener una mayor robustez frente a interferencias ya que la recepción o no de un servicio no depende de si el canal que lo alberga está o no interferido. TFS fue introducido en primer lugar como un anexo informativo en DVB-T2 (no normativo) y posteriormente fue adoptado en DVB-NGH (Next Generation Handheld). TFS y CB han sido propuestos para su inclusión en ATSC 3.0. Aún así, nunca han sido implementados. Las investigaciones llevadas a cabo en esta Tesis emplean diversos enfoques basados en teoría de la información para obtener los límites de ganancia, en simulaciones de capa física para evaluar el rendimiento en sistemas reales y en el análisis de medidas de campo. Estos estudios reportan ganancias en cobertura en torno a 4-5 dB con 4 canales e importantes ganancias en capacidad aún con sólo 2 canales RF. Esta tesis también se centra en los aspectos de implementación. Los receptores para CB requieren un sintonizador por canal RF agregado. La implementación de TFS con un solo sintonizador exige el cumplimiento de varios requisito temporales. Sin embargo, el uso de dos sintonizadores permitiría un buen rendimiento con una implementación más rentable con la reutilización de los actuales chips o su introducción junto con las arquitecturas existentes que operan con un doble sintonizador tales como[CA] La televisió digital terrestre (TDT) d'última generació està orientada a una necessària millora de l'eficiència espectral a fi d'abordar els desafiaments derivats de l'escassetat d'espectre com a resultat de la progressiva assignació de freqüències - l'anomenat Dividend Digital - per a satisfer la creixent demanda de capacitat per a la banda ampla sense fil. Els avanços tant en els estàndards de transmissió com de codificació de vídeo són de la màxima importància per a la progressiva posada en marxa de serveis d'alta qualitat com la televisió d'Ultra AD (Alta Definició). La transició a l'estàndard europeu de segona generació DVB-T2 i la introducció de la codificació de vídeo MPEG-4/AVC ja permet la transmissió de 4-5 serveis de televisió d'AD per canal RF (Radiofreqüència). No obstant això, la impossibilitat d'assignar una major taxa de bit sobre l'espectre restant podria posar en perill l'evolució de les plataformes de TDT en favor d'altres sistemes d'alta capacitat com ara el satèl·lit o les distribuïdores de cable. El següent pas se centra en el desplegament del recent estàndard HEVC (High Efficiency Vídeo Coding), que oferix un 50% de guany de codificació respecte a AVC, junt amb els estàndards terrestres de pròxima generació, la qual cosa podria garantir la competitivitat de la TDT en un futur pròxim. Aquesta tesi aborda l'ús de tecnologies d'agregació de canals RF que permeten incrementar l'eficiència espectral de les futures xarxes. La tesi se centra entorn de dues tecnologies: Time Frequency Slicing (TFS) i Channel Bonding (CB). TFS i CB consistixen en la transmissió de les dades d'un servei de televisió a través de múltiples canals RF en compte d'utilitzar un sol canal. CB difon les dades d'un servei a través d'uns quants canals RF convencionals formant un RF-Mux. TFS difon les dades a través de ranures temporals en diferents canals RF. Les dades són recuperades de forma seqüencial en el receptor per mitjà de salts en freqüència. La implementació d'aquestes tècniques permet obtindre guanys en capacitat i cobertura. La primera d'elles prové d'una multiplexació estadística (StatMux) de serveis de taxa variable (VBR) més eficient. A més, CB permet augmentar la taxa de pic d'un servei de forma proporcional al nombre de canals així com avantatges al combinar-la amb codificació de vídeo escalable. El guany en cobertura prové d'un millor rendiment RF a causa de la recepció de les dades d'un servei des de diferents canals en lloc de només un que podria estar degradat. De la mateixa manera, és possible obtindre una major robustesa enfront d'interferències ja que la recepció o no d'un servei no depén de si el canal que l'allotja està o no interferit. TFS va ser introduït en primer lloc com un annex informatiu en DVB-T2 (no normatiu) i posteriorment va ser adoptat en DVB-NGH (Next Generation Handheld). TFS i CB han sigut proposades per a la seva inclusió en ATSC 3.0. Encara així, mai han sigut implementades. Les investigacions dutes a terme en esta Tesi empren diverses vessants basades en teoria de la informació per a obtindre els límits de guany, en simulacions de capa física per a avaluar el rendiment en sistemes reals i en l'anàlisi de mesures de camp. Aquestos estudis reporten guanys en cobertura entorn als 4-5 dB amb 4 canals i importants guanys en capacitat encara amb només 2 canals RF. Esta tesi també se centra en els aspectes d'implementació. Els receptors per a CB requerixen un sintonitzador per canal RF agregat. La implementació de TFS amb un sol sintonitzador exigix el compliment de diversos requisit temporals. No obstant això, l'ús de dos sintonitzadors permetria un bon rendiment amb una implementació més rendible amb la reutilització dels actuals xips o la seua introducció junt amb les arquitectures existents que operen amb un doble sintonitzador com ara MIMO (Multiple Input Multiple Output).Giménez Gandia, JJ. (2015). Improved Spectrum Usage with Multi-RF Channel Aggregation Technologies for the Next-Generation Terrestrial Broadcasting [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/52520TESI

5G New Radio for Terrestrial Broadcast: A Forward-Looking Approach for NR-MBMS

"© 2019 IEEE. Personal use of this material is permitted. Permissíon from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertisíng or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works."[EN] 3GPP LTE eMBMS release (Rel-) 14, also referred to as further evolved multimedia broadcast multicast service (FeMBMS) or enhanced TV (EnTV), is the first mobile broadband technology standard to incorporate a transmission mode designed to deliver terrestrial broadcast services from conventional high power high tower (HPHT) broadcast infrastructure. With respect to the physical layer, the main improvements in FeMBMS are the support of larger inter-site distance for single frequency networks (SFNs) and the ability to allocate 100% of a carrier's resources to the broadcast payload, with self-contained signaling in the downlink. From the system architecture perspective, a receive-only mode enables free-to-air (FTA) reception with no need for an uplink or SIM card, thus receiving content without user equipment registration with a network. These functionalities are only available in the LTE advanced pro specifications as 5G new radio (NR), standardized in 3GPP from Rel-15, has so far focused entirely on unicast. This paper outlines a physical layer design for NR-MBMS, a system derived, with minor modifications, from the 5G-NR specifications, and suitable for the transmission of linear TV and radio services in either single-cell or SFN operation. This paper evaluates the NR-MBMS proposition and compares it to LTE-based FeMBMS in terms of flexibility, performance, capacity, and coverage.This work was supported in part by the European Commission through the 5G-PPP Project 5G-Xcast (H2020-ICT-2016-2 call) under Grant 761498.Gimenez, JJ.; Carcel, JL.; Fuentes, M.; Garro, E.; Elliott, S.; Vargas, D.; Menzel, C.... (2019). 5G New Radio for Terrestrial Broadcast: A Forward-Looking Approach for NR-MBMS. IEEE Transactions on Broadcasting. 65(2):356-368. https://doi.org/10.1109/TBC.2019.291211735636865

Advanced OFDM systems for terrestrial multimedia links

Recently, there has been considerable discussion about new wireless technologies and standards able to achieve high data rates. Due to the recent advances of digital signal processing and Very Large Scale Integration (VLSI) technologies, the initial obstacles encountered for the implementation of Orthogonal Frequency Division Multiplexing (OFDM) modulation schemes, such as massive complex multiplications and high speed memory accesses, do not exist anymore. OFDM offers strong multipath protection due to the insertion of the guard interval; in particular, the OFDM-based DVB-T standard had proved to offer excellent performance for the broadcasting of multimedia streams with bitrates over ten megabits per second in difficult terrestrial propagation channels, for fixed and portable applications. Nevertheless, for mobile scenarios, improving the receiver design is not enough to achieve error-free transmission especially in presence of deep shadow and multipath fading and some modifications of the standard can be envisaged. To address long and medium range applications like live mobile wireless television production, some further modifications are required to adapt the modulated bandwidth and fully exploit channels up to 24MHz wide. For these reasons, an extended OFDM system is proposed that offers variable bandwidth, improved protection to shadow and multipath fading and enhanced robustness thanks to the insertion of deep time-interleaving coupled with a powerful turbo codes concatenated error correction scheme. The system parameters and the receiver architecture have been described in C++ and verified with extensive simulations. In particular, the study of the receiver algorithms was aimed to achieve the optimal tradeoff between performances and complexity. Moreover, the modulation/demodulation chain has been implemented in VHDL and a prototype system has been manufactured. Ongoing field trials are demonstrating the ability of the proposed system to successfully overcome the impairments due to mobile terrestrial channels, like multipath and shadow fading. For short range applications, Time-Division Multiplexing (TDM) is an efficient way to share the radio resource between multiple terminals. The main modulation parameters for a TDM system are discussed and it is shown that the 802.16a TDM OFDM physical layer fulfills the application requirements; some practical examples are given. A pre-distortion method is proposed that exploit the reciprocity of the radio channel to perform a partial channel inversion achieving improved performances with no modifications of existing receivers

On Transmission System Design for Wireless Broadcasting

This thesis considers aspects related to the design and standardisation of transmission systems for wireless broadcasting, comprising terrestrial and mobile reception. The purpose is to identify which factors influence the technical decisions and what issues could be better considered in the design process in order to assess different use cases, service scenarios and end-user quality. Further, the necessity of cross-layer optimisation for efficient data transmission is emphasised and means to take this into consideration are suggested. The work is mainly related terrestrial and mobile digital video broadcasting systems but many of the findings can be generalised also to other transmission systems and design processes. The work has led to three main conclusions. First, it is discovered that there are no sufficiently accurate error criteria for measuring the subjective perceived audiovisual quality that could be utilised in transmission system design. Means for designing new error criteria for mobile TV (television) services are suggested and similar work related to other services is recommended. Second, it is suggested that in addition to commercial requirements there should be technical requirements setting the frame work for the design process of a new transmission system. The technical requirements should include the assessed reception conditions, technical quality of service and service functionalities. Reception conditions comprise radio channel models, receiver types and antenna types. Technical quality of service consists of bandwidth, timeliness and reliability. Of these, the thesis focuses on radio channel models and errorcriteria (reliability) as two of the most important design challenges and provides means to optimise transmission parameters based on these. Third, the thesis argues that the most favourable development for wireless broadcasting would be a single system suitable for all scenarios of wireless broadcasting. It is claimed that there are no major technical obstacles to achieve this and that the recently published second generation digital terrestrial television broadcasting system provides a good basis. The challenges and opportunities of a universal wireless broadcasting system are discussed mainly from technical but briefly also from commercial and regulatory aspectSiirretty Doriast

Cross-Layer Optimization of DVB-T2 System for Mobile Services

Mobile broadcast services have experienced a strong boost in recent years through the standardization of several mobile broadcast systems such as DVB-H, ATSC-M/H, DMB-T/H, and CMMB. However, steady need for higher quality services is projected to surpass the capabilities of the existing mobile broadcast systems. Consequently, work on new generations of mobile broadcast technology is starting under the umbrella of different industry consortia, such as DVB. In this paper, we address the question of how DVB-T2 transmission can be optimized for improved mobile broadcast reception. We investigate cross-layer optimization techniques with a focus on the transport of scalable video (SVC) streams over DVB-T2 Physical Layer Pipes (PLP). Throughout the paper, we propose different optimization options and verify their utility

Design of a simulation platform to test next generation of terrestrial DVB

Digital Terrestrial Television Broadcasting (DTTB) is a member of our daily life routine, and nonetheless, according to new users’ necessities in the fields of communications and leisure, new challenges are coming up. Moreover, the current Standard is not able to satisfy all the potential requirements. For that reason, first of all, a review of the current Standard has been performed within this work. Then, it has been identified the needing of developing a new version of the standard, ready to support enhanced services, as for example broadcasting transmissions to moving terminals or High Definition Television (HDTV) transmissions, among others. The main objective of this project is the design and development of a physical layer simulator of the whole DVB-T standard, including both the complete transmission and reception procedures. The simulator has been developed in Matlab. A detailed description of the simulator both from a functional and an architectural point of view is included. The simulator is the base for testing any possible modifications that may be included into the DVB-T2 future standard. In fact, several proposed enhancements have already been carried out and their performance has been evaluated. Specifically, the use of higher order modulation schemes, and the corresponding modifications in all the system blocks, have been included and evaluated. Furthermore, the simulator will allow testing other enhancements as the use of more efficient encoders and interleavers, MIMO technologies, and so on. A complete set of numerical results showing the performance of the different parts of the system, are presented in order to validate the correctness of the implementation and to evaluate both the current standard performance and the proposed enhancements. This work has been performed within the context of a project called FURIA, which is a strategic research project funded by the Spanish Ministry of Industry, Tourism and Commerce. A brief description of this project and its consortium has been also included herein, together with an introduction to the current situation of the DTTB in Spain (called TDT in Spanish)

Design of a simulation platform to test next generation of terrestrial DVB

Digital Terrestrial Television Broadcasting (DTTB) is a member of our daily life routine, and nonetheless, according to new users’ necessities in the fields of communications and leisure, new challenges are coming up. Moreover, the current Standard is not able to satisfy all the potential requirements. For that reason, first of all, a review of the current Standard has been performed within this work. Then, it has been identified the needing of developing a new version of the standard, ready to support enhanced services, as for example broadcasting transmissions to moving terminals or High Definition Television (HDTV) transmissions, among others. The main objective of this project is the design and development of a physical layer simulator of the whole DVB-T standard, including both the complete transmission and reception procedures. The simulator has been developed in Matlab. A detailed description of the simulator both from a functional and an architectural point of view is included. The simulator is the base for testing any possible modifications that may be included into the DVB-T2 future standard. In fact, several proposed enhancements have already been carried out and their performance has been evaluated. Specifically, the use of higher order modulation schemes, and the corresponding modifications in all the system blocks, have been included and evaluated. Furthermore, the simulator will allow testing other enhancements as the use of more efficient encoders and interleavers, MIMO technologies, and so on. A complete set of numerical results showing the performance of the different parts of the system, are presented in order to validate the correctness of the implementation and to evaluate both the current standard performance and the proposed enhancements. This work has been performed within the context of a project called FURIA, which is a strategic research project funded by the Spanish Ministry of Industry, Tourism and Commerce. A brief description of this project and its consortium has been also included herein, together with an introduction to the current situation of the DTTB in Spain (called TDT in Spanish)