Burst-by-Burst Adaptive Decision Feedback Equalised TCM, TTCM and BICM for H.263-Assisted Wireless Video Telephony

Decision Feedback Equaliser (DFE) aided wideband Burst-by-Burst (BbB) Adaptive Trellis Coded Modulation (TCM), Turbo Trellis Coded Modulation (TTCM) and Bit-Interleaved Coded Modulation (BICM) assisted H.263-based video transceivers are proposed and characterised in performance terms when communicating over the COST 207 Typical Urban wideband fading channel. Specifically, four different modulation modes, namely 4QAM, 8PSK, 16QAM and 64QAM are invoked and protected by the above-mentioned coded modulation schemes. The TTCM assisted scheme was found to provide the best video performance, although at the cost of the highest complexity. A range of lower-complexity arrangements will also be characterised. Finally, in order to confirm these findings in an important practical environment, we have also investigated the adaptive TTCM scheme in the CDMA-based Universal Mobile Telecommunications System's (UMTS) Terrestrial Radio Access (UTRA) scenario and the good performance of adaptive TTCM scheme recorded when communicating over the COST 207 channels was retained in the UTRA environment

Near far resistant detection for CDMA personal communication systems.

The growth of Personal Communications, the keyword of the 90s, has already the signs of a technological revolution. The foundations of this revolution are currently set through the standardization of the Universal Mobile Telecommunication System (UMTS), a communication system with synergistic terrestrial and satellite segments. The main characteristic of the UMTS radio interface, is the provision of ISDN services. Services with higher than voice data rates require more spectrum, thus techniques that utilize spectrum as efficiently as possible are currently at the forefront of the research community interests. Two of the most spectrally efficient multiple access technologies, namely. Code Division Multiple Access (CDMA) and Time Division Multiple Access (TDMA) concentrate the efforts of the European telecommunity.This thesis addresses problems and. proposes solutions for CDMA systems that must comply with the UMTS requirements. Prompted by Viterbi's call for further extending the potential of CDMA through signal processing at the receiving end, we propose new Minimum Mean Square Error receiver architectures. MMSE detection schemes offer significant advantages compared to the conventional correlation based receivers as they are NEar FAr Resistant (NEFAR) over a wide range of interfering power levels. The NEFAR characteristic of these detectors reduces considerably the requirements of the power control loops currently found in commercial CDMA systems. MMSE detectors are also found, to have significant performance gains over other well established interference cancellation techniques like the decorrelating detector, especially in heavily loaded system conditions. The implementation architecture of MMSE receivers can be either Multiple-Input Multiple Output (MIMO) or Single-Input Single-Output. The later offers not only complexity that is comparable to the conventional detector, but also has the inherent advantage of employing adaptive algorithms which can be used to provide both the dispreading and the interference cancellation function, without the knowledge of the codes of interfering users. Furthermore, in multipath fading channels, adaptive MMSE detectors can exploit the multipath diversity acting as RAKE combiners. The later ability is distinctive to MMSE based receivers, and it is achieved in an autonomous fashion, without the knowledge of the multipath intensity profile. The communicator achieves its performance objectives by the synergy of the signal processor and the channel decoder. According to the propositions of this thesis, the form of the signal processor needs to be changed, in order to exploit the horizons of spread spectrum signaling. However, maximum likelihood channel decoding algorithms need not change. It is the way that these algorithms are utilized that needs to be revis ed. In this respect, we identify three major utilization scenarios and an attempt is made to quantify which of the three best matches the requirements of a UMTS oriented CDMA radio interface. Based on our findings, channel coding can be used as a mapping technique from the information bit to a more ''intelligent" chip, matching the ''intelligence" of the signal processor

A Mobile Wireless Channel State Recognition Algorihm: Introduction, Definition, and Verification - Sensing for Cognitive Environmental Awareness

This research includes mobile wireless systems limited by time and frequency dispersive channels. A blind mobile wireless channel (MWC) state recognition (CSR) algorithm that detects hidden coherent nonselective and noncoherent selective processes is verified. Because the algorithm is blind, it releases capacity based on current channel state that traditionally is fixed and reserved for channel gain estimation and distortion mitigation. The CSR algorithm enables cognitive communication system control including signal processing, resource allocation/deallocation, or distortion mitigation selections based on channel coherence states. MWC coherent and noncoherent states, ergodicity, stationarity, uncorrelated scattering, and Markov processes are assumed for each time block. Furthermore, a hidden Markov model (HMM) is utilized to represent the statistical relationships between hidden dispersive processes and observed receive waveform processes. First-order and second-order statistical extracted features support state hard decisions which are combined in order to increase the accuracy of channel state estimates. This research effort has architected, designed, and verified a blind statistical feature recognition algorithm capable of detecting coherent nonselective, single time selective, single frequency selective, or dual selective noncoherent states. A MWC coherence state model (CSM) was designed to represent these hidden dispersive processes. Extracted statistical features are input into a parallel set of trained HMMs that compute state sequence conditional likelihoods. Hard state decisions are combined to produce a single most likely channel state estimate for each time block. To verify the CSR algorithm performance, combinations of hidden state sequences are applied to the CSR algorithm and verified against input hidden state sequences. State sequence recognition accuracy sensitivity was found to be above 99% while specificity was determined to be above 98% averaged across all features, states, and sequences. While these results establish the feasibility of a MWC blind CSR algorithm, optimal configuration requires future research to further improve performance including: 1) characterizing the range of input signal configurations, 2) waveform feature block size reduction, 3) HMM parameter tracking, 4) HMM computational complexity and latency reduction, 5) feature soft decision combining, 6) recursive implementation, 7) interfacing with state based mobile wireless communication control processes, and 8) extension to wired or wireless waveform recognition

Self-concatenated coding for wireless communication systems

In this thesis, we have explored self-concatenated coding schemes that are designed for transmission over Additive White Gaussian Noise (AWGN) and uncorrelated Rayleigh fading channels. We designed both the symbol-based Self-ConcatenatedCodes considered using Trellis Coded Modulation (SECTCM) and bit-based Self- Concatenated Convolutional Codes (SECCC) using a Recursive Systematic Convolutional (RSC) encoder as constituent codes, respectively. The design of these codes was carried out with the aid of Extrinsic Information Transfer (EXIT) charts. The EXIT chart based design has been found an efficient tool in finding the decoding convergence threshold of the constituent codes. Additionally, in order to recover the information loss imposed by employing binary rather than non-binary schemes, a soft decision demapper was introduced in order to exchange extrinsic information withthe SECCC decoder. To analyse this information exchange 3D-EXIT chart analysis was invoked for visualizing the extrinsic information exchange between the proposed Iteratively Decoding aided SECCC and soft-decision demapper (SECCC-ID). Some of the proposed SECTCM, SECCC and SECCC-ID schemes perform within about 1 dB from the AWGN and Rayleigh fading channels’ capacity. A union bound analysis of SECCC codes was carried out to find the corresponding Bit Error Ratio (BER) floors. The union bound of SECCCs was derived for communications over both AWGN and uncorrelated Rayleigh fading channels, based on a novel interleaver concept.Application of SECCCs in both UltraWideBand (UWB) and state-of-the-art video-telephone schemes demonstrated its practical benefits.In order to further exploit the benefits of the low complexity design offered by SECCCs we explored their application in a distributed coding scheme designed for cooperative communications, where iterative detection is employed by exchanging extrinsic information between the decoders of SECCC and RSC at the destination. In the first transmission period of cooperation, the relay receives the potentially erroneous data and attempts to recover the information. The recovered information is then re-encoded at the relay using an RSC encoder. In the second transmission period this information is then retransmitted to the destination. The resultant symbols transmitted from the source and relay nodes can be viewed as the coded symbols of a three-component parallel-concatenated encoder. At the destination a Distributed Binary Self-Concatenated Coding scheme using Iterative Decoding (DSECCC-ID) was employed, where the two decoders (SECCC and RSC) exchange their extrinsic information. It was shown that the DSECCC-ID is a low-complexity scheme, yet capable of approaching the Discrete-input Continuous-output Memoryless Channels’s (DCMC) capacity.Finally, we considered coding schemes designed for two nodes communicating with each other with the aid of a relay node, where the relay receives information from the two nodes in the first transmission period. At the relay node we combine a powerful Superposition Coding (SPC) scheme with SECCC. It is assumed that decoding errors may be encountered at the relay node. The relay node then broadcasts this information in the second transmission period after re-encoding it, again, using a SECCC encoder. At the destination, the amalgamated block of Successive Interference Cancellation (SIC) scheme combined with SECCC then detects and decodes the signal either with or without the aid of a priori information. Our simulation results demonstrate that the proposed scheme is capable of reliably operating at a low BER for transmission over both AWGN and uncorrelated Rayleigh fading channels. We compare the proposed scheme’s performance to a direct transmission link between the two sources having the same throughput

Optimization of multidimensional equalizers based on MMSE criteria for multiuser detection

PhD ThesisThis thesis is about designing a multidimensional equalizer for uplink interleaved division multiple access (IDMA) transmission. Multidimensional equalizer can be classified into centralized and decentralized multidimensional equalizer. Centralized multidimensional equalizer (MDE) have been used to remove both inter-symbol interference (ISI) and multiaccess interference (MAI) effects from the received signal. In order to suppress MAI effects, code division multiple access (CDMA) has been used with MDE to minimize the correlation between users' signals. The MDE structure can be designed using linear equalizer (MLE) or decision feedback equalizer (MDFE). Previous studies on MDE employed adaptive algorithms to estimate filter co-effi cients during the training mode, i.e. the symbol equalization was not optimal, for two users. In our work, we applied MDE on IDMA receiver for multipath selective fading channels and also derived new equations to obtain the optimal filter taps for both types of MDE equalizers, i.e. MDFE and MLE, based on the minimum mean square error (MMSE) criterion. The optimal filter taps are calculated for more than two users. Moreover, we investigated the performance of the optimal MDFE using both IDMA (MDFE-IDMA) and CDMA (MDFE-CDMA) detectors. Generally, the MDE equalizer suffers from residual MAI interference effects at low signal-to-noise-ratios (SNR) due to the delay inherent in the convergence of the crossover filter taps. Therefore, a new decentralized multidimensional equalizer has been proposed to IDMA detector. Within design of decentralized equalizer, the convergence problem has been resolved by replacing the crossover filters with parallel interference canceler (PIC) for removing MAI dispersion. The proposed decentralized multidimensional equalizer shows a higher efficiency in removing MAI interference when compared with existing receivers in the literature. However, this is achieved at the expense of higher computational complexity compared to centralized multidimensional equalization

Investigation of coding and equalization for the digital HDTV terrestrial broadcast channel

Includes bibliographical references (p. 241-248).Supported by the Advanced Telecommunications Research Program.Julien J. Nicolas

Factor Graph Based Detection Schemes for Mobile Terrestrial DVB Systems with Long OFDM Blocks

This PhD dissertation analyzes the performance of second generation digital video broadcasting (DVB) systems in mobile terrestrial environments and proposes an iterative detection algorithm based on factor graphs (FG) to reduce the distortion caused by the time variation of the channel, providing error-free communication in very severe mobile conditions. The research work focuses on mobile scenarios where the intercarrier interference (ICI) is very high: high vehicular speeds when long orthogonal frequency-division multiplexing (OFDM) blocks are used. As a starting point, we provide the theoretical background on the main topics behind the transmission and reception of terrestrial digital television signals in mobile environments, along with a general overview of the main signal processing techniques included in last generation terrestrial DVB systems. The proposed FG-based detector design is then assessed over a simpli ed bit-interleaved coded modulation (BICM)-OFDM communication scheme for a wide variety of mobile environments. Extensive simulation results show the e ectiveness of the proposed belief propagation (BP) algorithm over the channels of interest in this research work. Moreover, assuming that low density parity-check (LDPC) codes are decoded by means of FG-based algorithms, a high-order FG is de ned in order to accomplish joint signal detection and decoding into the same FG framework, o ering a fully parallel structure very suitable when long OFDM blocks are employed. Finally, the proposed algorithms are analyzed over the physical layer of DVB-T2 speci cation. Two reception schemes are proposed which exploit the frequency and time-diversity inherent in time-varying channels with the aim of achieving a reasonable trade-o among performance, complexity and latency.Doktoretza tesi honek bigarren belaunaldiko telebista digitalaren eraginkortasuna aztertzen du eskenatoki mugikorrean, eta faktoreen grafoetan oinarritzen den hartzaile iteratibo bat proposatzen du denboran aldakorra den kanalak sortzen duen distortsioa leundu eta seinalea errorerik gabe hartzea ahalbidetzen duena. Proposatutako detektorea BICM-OFDM komunikazio eskema orokor baten gainean ebaluatu da lurreko broadcasting kanalaren baldintzak kontutan hartuz. Simulazio emaitzek algoritmo honen eraginkortasuna frogatzen dute Doppler frekuentzia handietan. Ikerketa lanaren bigarren zatian, faktoreen grafoetan oinarritutako detektorea eskema turbo zabalago baten baitan txertatu da LDPC dekodi katzaile batekin batera. Hartzaile diseinu honen abantaila nagusia da OFDM simbolo luzeetara ondo egokitzen dela. Azkenik, proposatutako algoritmoa DVB-T2 katearen baitan inplementatu da, bi hartzaile eskema proposatu direlarik seinaleak duen dibertsitate tenporal eta frekuentziala probesteko, beti ere eraginkortasunaren, konplexutasunaren eta latentziaren arteko konpromisoa mantenduz.Este trabajo de tesis analiza el rendimiento de la segunda generación de la televisión digital terreste en escenarios móviles y propone un algoritmo iterativo basado en grafos de factores para la detección de la señal y la reducción de la distorsión causada por la variación temporal del canal, permitiendo así recibir la señal libre de errores. El detector basado en grafos de factores propuesto es evaluado sobre un esquema de comunicaciones general BICM-OFDM en condiciones de transmisión propios de canales de difusión terrestres. Los resultados de simulación presentados muestran la e ciencia del algoritmo de detección propuesto en presencia de frecuencias Doppler muy altas. En una segunda parte del trabajo de investigación, el detector propuesto es incorporado a un esquema turbo junto con un decodi cador LDPC, dando lugar a un receptor iterativo que presenta características especialmente apropiadas para su implementación en sistemas OFDM con longitudes de símbolo elevadas. Por último, se analiza la implementación del algoritmo propuesto sobre la cadena de recepción de DVB-T2. Se presentan dos esquemas de recepción que explotan la diversidad temporal y frecuencial presentes en la señal afectada por canales variantes en el tiempo, consiguiendo un compromiso razonable entre rendimiento, complejidad y latencia

Doppler compensation algorithms for DSP-based implementation of OFDM underwater acoustic communication systems

In recent years, orthogonal frequency division multiplexing (OFDM) has gained considerable attention in the development of underwater communication (UWC) systems for civilian and military applications. However, the wideband nature of the communication links necessitate robust algorithms to combat the consequences of severe channel conditions such as frequency selectivity, ambient noise, severe multipath and Doppler Effect due to velocity change between the transmitter and receiver. This velocity perturbation comprises two scenarios; the first induces constant time scale expansion/compression or zero acceleration during the transmitted packet time, and the second is time varying Doppler-shift. The latter is an increasingly important area in autonomous underwater vehicle (AUV) applications. The aim of this thesis is to design a low complexity OFDM-based receiver structure for underwater communication that tackles the inherent Doppler effect and is applicable for developing real-time systems on a digital signal processor (DSP). The proposed structure presents a paradigm in modem design from previous generations of single carrier receivers employing computationally expensive equalizers. The thesis demonstrates the issues related to designing a practical OFDM system, such as channel coding and peak-to-average power ratio (PAPR). In channel coding, the proposed algorithms employ convolutional bit-interleaved coded modulation with iterative decoding (BICM-ID) to obtain a higher degree of protection against power fading caused by the channel. A novel receiver structure that combines an adaptive Doppler-shift correction and BICM-ID for multi-carrier systems is presented. In addition, the selective mapping (SLM) technique has been utilized for PAPR. Due to their time varying and frequency selective channel nature, the proposed systems are investigated via both laboratory simulations and experiments conducted in the North Sea off the UK’s North East coast. The results of the study show that the proposed systems outperform block-based Doppler-shift compensation and are capable of tracking the Doppler-shift at acceleration up to 1m /s2.EThOS - Electronic Theses Online ServiceIraqi Government's Ministry of Higher Education and Scientific ResearchGBUnited Kingdo

Iterative receivers and multichannel equalisation for time division multiple access systems

The thesis introduces receiver algorithms improving the performance of TDMA mobile radio systems. Particularly, we consider receivers utilising side information, which can be obtained from the error control coding or by having a priori knowledge of interference sources. Iterative methods can be applied in the former case and interference suppression techniques in the latter. Convolutional coding adds redundant information into the signal and thereby protects messages transmitted over a radio channel. In the coded systems the receiver is usually comprised of separate channel estimation, detection and channel decoding tasks due to complexity restrictions. This suboptimal solution suffers from performance degradation compared to the optimal solution achieved by optimising the joint probability of information bits, transmitted symbols and channel impulse response. Conventional receiver utilises estimated channel state information in the detection and detected symbols in the channel decoding to finally obtain information bits. However, the channel decoder provides also extrinsic information on the bit probabilities, which is independent of the received information at the equaliser input. Therefore it is beneficial to re-perform channel estimation and detection using this new extrinsic information together with the original input signal. We apply iterative receiver techniques mainly to Enhanced General Packet Radio System (EGPRS) using GMSK modulation for iterative channel estimation and 8-PSK modulation for iterative detection scheme. Typical gain for iterative detection is around 2 dB and for iterative channel estimation around 1 dB. Furthermore, we suggest two iteration rounds as a reasonable complexity/performance trade-off. To obtain further complexity reduction we introduce the soft trellis decoding technique that reduces the decoder complexity significantly in the iterative schemes. Cochannel interference (CCI) originates from the nearby cells that are reusing the same transmission frequency. In this thesis we consider CCI suppression by joint detection (JD) technique, which detects simultaneously desired and interfering signals. Because of the complexity limitations we only consider JD for two binary modulated signals. Therefore it is important to find the dominant interfering signal (DI) to achieve the best performance. In the presence of one strong DI, the JD provides major improvement in the receiver performance. The JD requires joint channel estimation (JCE) for the two signals. However, the JCE makes the implementation of the JD more difficult, since it requires synchronised network and unique training sequences with low cross-correlation for the two signals.reviewe