Power loss minimization in electric cars by wheel force allocation

The need for lowering the emission levels has never been greater than now. In the vehicle industry, electrification seems to be an irreversible way ahead but user-related challenges such as limited range delay electricity as the primary energy source for personal transportation. Other control-related challenges are also introduced as electric cars are over-actuated, i.e. several actuators can be used for the same purpose. Over-actuation introduces the possibility to choose more freely which actuator to use when. Can this freedom of choice be used to improve energy efficiency of electric cars by e.g. minimizing power losses? In this thesis, two wheel force distribution algorithms have been developed with a method called control allocation. The algorithms minimize power losses in the electric drivetrain, transmission and tires. They were tested in a simulated city cycle in a Volvo V60 configuration with four electric motors, each connected to a wheel through a single speed transmission and coupling respectively. It was found that by using developed algorithms, up to 3.9% energy could be saved. In a next step, the transmission ratio on the front motors and rear motors were optimized in combination with one of the algorithms. By using a larger transmission ratio in the front than in the rear, the energy consumption reduced even further. With these development steps, up to 7.9% energy could be saved compared to the original vehicle

A fast and parametric torque distribution strategy for four-wheel-drive energy-efficient electric vehicles

Electric vehicles (EVs) with four individually controlled drivetrains are over-actuated systems, and therefore, the total wheel torque and yaw moment demands can be realized through an infinite number of feasible wheel torque combinations. Hence, an energy-efficient torque distribution among the four drivetrains is crucial for reducing the drivetrain power losses and extending driving range. In this paper, the optimal torque distribution is formulated as the solution of a parametric optimization problem, depending on the vehicle speed. An analytical solution is provided for the case of equal drivetrains, under the experimentally confirmed hypothesis that the drivetrain power losses are strictly monotonically increasing with the torque demand. The easily implementable and computationally fast wheel torque distribution algorithm is validated by simulations and experiments on an EV demonstrator, along driving cycles and cornering maneuvers. The results show considerable energy savings compared to alternative torque distribution strategies

Energy reduction by power loss minimisation through wheel torque allocation in electric vehicles: a simulation-based approach

As vehicles become increasingly electrified, electrical machines for propulsion can be divided into many sources making the vehicle highly over-actuated. For over-actuated vehicles, the allocation of a propulsive force is an underdetermined process with respect to both the number of wheels and electrical machines. Hence, the allocation can be made to favour particular attributes such as energy consumption. In this study, a vehicle equipped with four identical electric motors with a fixed transmission ratio connected through a half-shaft and a coupling to one wheel respectively is driven a 2-h-long city cycle in the vicinity of G\uf6teborg. Two different control allocation methods are presented to distribute torque momentaneously based on driver request while minimising power losses in electric motor and inverter as well as tyres. One method is a quadratic programming optimisation and the other is an offline exhaustive search method resulting in a look-up table based on requested torque and actual speed. The two methods are compared to other torque distribution strategies based on fixed distribution ratio and equal tyre-to-road friction utilisation. It was found that using the developed optimisation algorithms, a reduction of up to 3.9% in energy consumption can be obtained

Energy efficient torque vectoring control

Tire forces are at the heart of the dynamic qualities of vehicles. With the advent of electric vehicles the precise and accurate control of the traction and braking forces at the individual wheel becomes a possibility and a reality outside test labs and virtual proving grounds. Benefits of individual wheel torque control, or torque-vectoring, in terms of vehicle dynamics behavior have been well documented in the literature. However, very few studies exist which analyze the individual wheel torque control integrated with vehicle efficiency considerations. This paper focuses on this aspect and discusses the possibilities and benefits of integrated, energy efficient torque vectoring control. Experiments with a four-wheel-drive electric vehicle show that considerable energy savings can be achieved by considering drivetrain and tire power losses through energy efficient torque vectoring control

Energy-efficient torque-vectoring control of electric vehicles with multiple drivetrains

The safety benefits of torque-vectoring control of electric vehicles with multiple drivetrains are well known and extensively discussed in the literature. Also, several authors analyze wheel torque control allocation algorithms for reducing the energy consumption while obtaining the wheel torque demand and reference yaw moment specified by the higher layer of a torque-vectoring controller. Based on a set of novel experimental results, this study demonstrates that further significant energy consumption reductions can be achieved through the appropriate tuning of the reference understeer characteristics. The effects of drivetrain power losses and tire slip power losses are discussed for the case of identical drivetrains at the four vehicle corners. Easily implementable yet effective rule-based algorithms are presented for the set-up of the energy-efficient reference yaw rate, feedforward yaw moment and wheel torque distribution of the torque-vectoring controller

고성능 한계 핸들링을 위한 인휠모터 토크벡터링 제어

학위논문(박사) -- 서울대학교대학원 : 공과대학 기계항공공학부, 2021.8. 이경수.지난 10년 동안 차량 자세 제어시스템(ESC)은 치명적인 충돌을 방지하기 위해 많은 상용 차량에서 비약적으로 발전되고 개발되고 있다. 특히, 차량 자세 제어 시스템은 악천후로 인한 미끄러운 도로와 같은 위험한 도로에서 불안정한 차량 주행 조건에서 사고를 피하는데 큰 역할을 한다. 그러나, 최근의 경우, 고성능 차량 또는 스포츠카 등의 경우 제동제어의 빈번한 개입은 운전의 즐거움을 감소시키는 불만도 존재한다. 최근 차량의 전동화와 함께, 자량 자세 제어시스템의 작동 영역인 한계 주행 핸들링 조건에서 각 휠의 독립적인 구동을 적용 할 수 있는 시스템 중 하나인 인휠 모터 시스템을 사용하여 차량의 종, 횡방향 특성을 제어 가능하게 하는 토크 벡터링 제어기술에 대한 연구가 활발하다. 따라서, 본 연구에서는 차량의 선회 한계 핸들링 조건에서 안정성과 주행 다이나믹 성능을 향상시킬 수 있는 토크 벡터링 제어기를 제안하고자 한다. 먼저, 차량의 비선형 주행 구간인 한계 핸들링 조건에 대한 자동 드리프트 제어 알고리즘을 제안한다. 이 알고리즘을 이용하여 토크벡터링제어에 차량의 다이나믹한 주행모드에 대한 통찰력을 제공하고 미끄러운 도로에서 차량의 높은 슬립 각도의 안정성 제어를 제공 할 수 있다. 또한, 인휠 모터 시스템을 차량의 전륜에 2개 모터로 사용하여 차량 고유의 특성인 차량 언더스티어 구배를 직접적 제어를 수행하여, 차량의 핸들링 성능을 향상시켰다. 제어기의 채터링 효과를 줄이고 빠른 응답을 얻기 위해 새로운 과도 매개 변수가 이용하여 수식화하여 구성하였으며, 차량의 정상 상태 및 과도 특성 향상을 검증하기 위하여 ISO 기반 시뮬레이션 및 차량 실험을 수행하였다. 마지막으로 요 제어기와 횡 슬립 각도 제어기로 구성된 MASMC (Multiple Adaptive Sliding Mode Control) 접근 방식을 사용하는 4륜 모터 시스템을 사용한 동적 토크벡터링 제어를 수행하였다. 높은 비선형 특성을 가진 차량의 전후륜 타이어의 코너링 강성은 적응제어기법을 이용하여 예측하였다. 따라서, 안전모드와 다이나믹 모드를 구성하여, 운전자로 하여금 원하는 주행의 조건에 맞게 선택할 수 있는 알고리즘을 구현하였다. 이 MASMC 알고리즘은 향후 전동화 차량에 주행안정성 향상과 다이나믹한 주행의 즐거움을 주는 기술로써, 전차량 시뮬레이션을 이용하여 검증하였다.In the last ten decades, vehicle stability control systems have been dramatically developed and adapted in many commercial vehicles to avoid fatal crashes. Significantly, ESC (Electric Stability Control) system can help escape the accident from unstable driving conditions with dangerous roads such as slippery roads due to inclement weather conditions. However, for the high performed vehicle, frequent intervention from ESC reduces the pleasure of fun-to-drive. Recently, the development of traction control technologies has been taking place with that of the electrification of vehicles. The IWMs (In-Wheel Motor system), which is one of the systems that can apply independent drive of each wheel, for the limit handling characteristics, which are the operation areas of the ESC, is introduced for the control that enables the lateral characteristics of the vehicle dynamics. Firstly, the automated drift control algorithm can be proposed for the nonlinear limit handling condition of vehicles. This approach can give an insight of fun-to-drive mode to TV (Torque Vector) control scheme, but also the stability control of high sideslip angle of the vehicle on slippery roads. Secondly, using IWMs system with front two motors, understeer gradient of vehicle, which is the unique characteristics of vehicle can be used for the proposed control strategy. A new transient parameter is formulated to be acquired rapid response of controller and reducing chattering effects. Simulation and vehicle tests are conducted for validation of TV control algorithm with steady-state and transient ISO-based tests. Finally, dynamic torque vectoring control with a four-wheel motor system with Multiple Adaptive Sliding Mode Control (MASMC) approach, which is composed of a yaw rate controller and sideslip angle controller, is introduced. Highly nonlinear characteristics, cornering stiffnesses of front and rear tires are estimated by adaptation law with measuring data. Consequently, there are two types of driving modes, the safety mode and the dynamic mode. MASMC algorithm can be found and validated by simulation in torque vectoring technology to improve the handling performance of fully electric vehicles.Chapter 1 Introduction 7 1.1. Background and Motivation 7 1.2. Literature review 11 1.3. Thesis Objectives 15 1.4. Thesis Outline 15 Chapter 2 Vehicle dynamic control at limit handling 17 2.1. Vehicle Model and Analysis 17 2.1.1. Lateral dynamics of vehicle 17 2.1.2. Longitudinal dynamics of vehicle 20 2.2. Tire Model 24 2.3. Analysis of vehicle drift for fun-to-drive 28 2.4. Designing A Controller for Automated Drift 34 2.4.1. Lateral controller 35 2.4.2. Longitudinal Controller 37 2.4.3. Stability Analysis 39 2.4.4. Validation with simulation and test 40 Chapter 3 Torque Vectoring Control with Front Two Motor In-Wheel Vehicles 47 3.1. Dynamic Torque Vectoring Control 48 3.1.1. In-wheel motor system (IWMs) 48 3.1.2. Dynamic system modeling 49 3.1.3. Designing controller 53 3.2. Validation with Simulation and Experiment 59 3.2.1. Simulation 59 3.2.2. Vehicle Experiment 64 Chapter 4 Dynamic handling control for Four-wheel Drive In-Wheel platform 75 4.1. Vehicle System Modeling 76 4.2. Motion Control based on MASMC 78 4.2.1. Yaw motion controller for the inner ASMC 80 4.2.2. Sideslip angle controller for the outer ASMC 84 4.3. Optimal Torque Distribution (OTD) 88 4.3.1. Constraints of dynamics 88 4.3.2. Optimal torque distribution law 90 4.4. Validation with Simulation 91 4.4.1. Simulation setup 91 4.4.2. Simulation results 92 Chapter 5 Conclusion and Future works 104 5.1 Conclusion 104 5.2 Future works 106 Bibliography 108 Abstract in Korean 114박

NASA SBIR abstracts of 1990 phase 1 projects

The research objectives of the 280 projects placed under contract in the National Aeronautics and Space Administration (NASA) 1990 Small Business Innovation Research (SBIR) Phase 1 program are described. The basic document consists of edited, non-proprietary abstracts of the winning proposals submitted by small businesses in response to NASA's 1990 SBIR Phase 1 Program Solicitation. The abstracts are presented under the 15 technical topics within which Phase 1 proposals were solicited. Each project was assigned a sequential identifying number from 001 to 280, in order of its appearance in the body of the report. The document also includes Appendixes to provide additional information about the SBIR program and permit cross-reference in the 1990 Phase 1 projects by company name, location by state, principal investigator, NASA field center responsible for management of each project, and NASA contract number